Soleus Air SG-WAC-06ESE Bedienungsanleitung

Thank you for choosing a Soleus Air powered by Gree Air Conditioner. This owner’s manual will

provide you with valuable information necessary for the proper care and maintenance of your new

product. Please take a few moments to thoroughly read the instructions and familiarize yourself with

all the operational aspects of your new air conditioner.

For your own records, please attach a copy of your sales receipt to this manual. Also, write the store

name/location, date purchased, and serial number below:

Store Name: ____________________________________________________

Location: ______________________________________________________

Date Purchased: _________________________________________________

Serial Number (located on back of unit): ______________________________

IMPORTANT SAFETY INSTRUCTIONS

Before installing and using your air conditioner, please read this owner’s manual carefully. Store this

manual in a safe place for future reference. Your safety and the safety of others is very important to

us. Please pay attention to all safety messages outlined in this owner’s manual.

WARNING: To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow

the following basic precautions:

This is a safety alert symbol.

This symbol alerts you to potential hazards that can harm you or others or even cause

death.

All safety messages will directly follow the safety alert symbol and/or the words

“DANGER” or “WARNING”.

Failure to immediately follow these

instructions may cause serious injury

or even death.

All Safety messages alert you of potential hazards, how to reduce the chance of injury,

and what can happen if instructions are not followed correctly.

• Plug into a grounded 3 prong outlet.

• Do not remove the ground prong.

• Do not use a plug adapter.

• Do not use an extension cord.

• Unplug the air conditioner before servicing

• Use two or more people to move and install the air

conditioner

Recommended Ground Method

For your personal safety, this air conditioner must be grounded. This air conditioner is equipped with a 3 prong power

supply cord with a grounded plug. To minimize the possibility of electrical shock, the cord must be plugged into a 3 prong

outlet and grounded in accordance with all local codes and ordinances. If a 3 prong outlet is not available, it is the cus-

tomer’s responsibility to have a properly grounded 3 prong outlet installed by a qualified electrician.

LCDI Power Cord and Plug

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord and plug as

required by US National Electric Code 440.65. This cord consists of a length of shielded flexible cord with no termination

on the load side and a LCDI attachment plug on the line side.

The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the nominal current

leakage between the cord shield and either load conductor exceeds a predetermined value. The cord will remain de-

energized until the devise has been manually reset. This is intended to reduce the risk of a fire in the power cord or

combustible materials nearby. The cord shields are not grounded and they must be considered a shock hazards if

exposed. The cord shield must not be connected to ground or to any exposed metal.

The test and reset buttons on the LCDI Plug are used to check if

the plug is functioning properly. To test the plug:

1. Plug power cord into a wall outlet

2. Press the TEST Button, the circuit should trip and cut all

power to the air conditioner

3. Press the RESET button for use

If a test is performed and the indicator light remains ON, the

current leakage has been detected. Do not use the air

conditioner or attempt to reset the LCDI Plug. Contact Customer

Service for troubleshooting recommendations.

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove the ground prong.

Do not use an adapter

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock

The electrical ratings for your air conditioner are listed on the model and serial

number label located on the front left side of the unit (when facing the front).

Specific electrical requirements are listed in the chart below. Follow the

requirements below for the type of plug on the power supply cord.

Power Supply Cord

• 115 volt (103.5 min.—126.5

max)

• 0-12 amps

• 15-amp time-delay fuse or

circuit breaker

• Use on single outlet circuit only

Wiring Requirements

It is the customer’s responsibility:

• To contact a qualified electrician

• To assure that the electrical installation is adequate

and in conformance with the National Electrical Code,

ANSI/NFPA 70 - latest edition, and all local codes and

ordinances.

Copies of the standards listed may be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, Massachusetts 02269

PACKING LIST

2/5”

Screw (4) Sash Lock (1)

3/4”

Screw (6)

Packing List:

• Window Air Conditioner

• Remote Control

• AAA Batteries (2)

• Top Mounting Rail

• Top Mounting Rail Seal Strip

• 2/5” Screw for Top Mounting Rail (4)

• Accordion Panels (Left & Right)

• Sash Lock (1)

• Window Sash Seal

• 3/4” Screw for Sash Lock & Accordion

Panels (6)

• Foam Top Window Gasket

• Owner’s Manual

SPECIFICATIONS

• Noise level is measured at a distance of 3.28 ft away from the front of the unit in cooling mode.

• Power consumption is measured when the fan runs at the highest speed setting.

• These specifications are for reference only. For actual data, please refer to the rating label on the unit.

Model SG-WAC-06SE

Power Supply (Ph/V/Hz) 1/115/60Hz

Dehumidifying Capacity (Pints/Day) 31.2

Rated Cooling Capacity (BTU/h) 6,000

Rated Heating Capacity (BTU/h) /

Cooling Power Input (Watts) 620

Heating Power Input (Watts) /

Rated Current Cooling (Amperage) 5.6

Rated Current Heating (Amperage) /

EER/C.O.P 9.7

Noise Level db (A) H/L 56/61

CFM 180

Design Pressure (PSIG) (H/L) /

Dimensions (W” x H” x D”) 18.59 x 12.75 x 15.72

Package Dimensions (W” x H” x D”) 21.84x 14.19 x 17.91

Net/Gross Weight (Lbs) 46/54

Refrigerant Charge (Oz) 12.35

SG-WAC-08ESE

1/115/60Hz

40.8

8,000

740

7.1

10.8

59/63

200

18.59 x 12.75 x 15.72

21.84x 14.19 x 17.91

49/56

16.58

Refrigerant Type R-410A R-410A

SG-WAC-06ESE

1/115/60Hz

6,300

590

5.3

10.7

56/61

180

18.59 x 12.75 x 15.72

21.84x 14.19 x 17.91

46/54

R-410A

13.05

INSTALLATION & ASSEMBLY INSTRUCTIONS

Some assembly is required for your new air conditioner. Please read and follow these instructions carefully.

1. This air conditioner is designed to be installed in a

standard double-hung window with a window width

between 21” and 38” .

2. The air conditioner can be installed without the

accordion panels to fit in a narrow window opening.

See the window dimensions.

3. The Lower Sash (the lower part of the window that

moves up and down) must allow for 13.5” of vertical

clearance when open. (See FIG. 1).

4. All supporting parts must be secured to firm wood,

masonry, or metal.

5. The electrical outlet must be within reach of the power

cord.

NOTE: Save the product packaging and installation instruc-

tions for future reference. Store the air conditioner in the

product box when not in use for an extended period of time.

FIG. 1

When handling the unit, be careful to avoid cuts from

the sharp metal edges and aluminum fins on the front

and rear coils.

21 38

13.5

ASSEMBLY & INSTALLATION (CONT.)

Storm Window Requirements

A storm window frame will not allow the air conditioner to

tilt properly which in turn will keep it from draining properly.

To adjust for this, attach a board or piece of wood to the

sill. The board or wood piece should have a depth of at

least 1 1/2”. Make sure the board or piece of wood is ap-

proximately 1/2” higher than the storm window frame. This

will allow the air conditioner to tilt enough for proper drain-

age. (See FIG. 2).

Placing the Unit Inside a Window

1. Place the air conditioner on the sill with the bottom

mounting rail against its back edge. Center the air con-

ditioner and close the window securely behind the top

mounting rail. The air conditioner should be slightly

tilted to the outside area. Use a level; about a 1/3 bub-

ble will be the correct case slant to the outside. (See

FIG. 5 & FIG. 6)

2. Once the air conditioner is placed, extend both the left

and right accordion panels to the width of the window.

Accordion Panel Installation

Now that you have installed the top rail, you can now install

the accordion panels on each side.

1. Place the air conditioner on a hard flat surface.

2. Locate the accordion panels in the box.

3. Gently pull the free end of the accordion panel (See

FIG. 2). Do this for both panels.

4. Slide the free end of the accordion panel into the side

panel of the air conditioner (See FIG. 3). Do this for

each side.

5. Once the accordion panels are slid into place adjust

the top and bottom rails of the accordion panels into

the top and bottom rails of the air conditioner (See FIG.

4).

SASH

1 1/2” MIN

(38 mm)

STORM

WINDOW

FRAME

Board or wood

piece must be

approximately

1/2” higher

than the storm

window frame

for proper

drainage

FIG. 2

FIG. 5

FIG. 6

FIG. 7

FIG. 3

FIG. 4

ASSEMBLY & INSTALLATION (CONT.)

3/4” Screws

Sash Lock

MOUNTING HARDWARE

Qty

Tools Needed:

Phillips Screw Driver

Drill (if plot holes are needed)

Sash Lock and Foam Seal Installation

1. Drive 3/4” screws into the top of the accordion panel

frame and the top rail to securely attach the window air

conditioner to the lower sash. (See FIG. 11/12)

3. To secure the lower sash into place, use the sash lock

and a 3/4” screw as shown below (See FIG. 12)

4. For added insulation, cut the supplied insulation foam to

the width of the window. Insert the foam between the

window sashes to prevent air and objects from getting

into the room. (See FIG. 13)

Removing the Air Conditioner from the

Window

1. Turn the air conditioner off, and disconnect the power

cord.

2. Remove the sash seal from between windows, and

unscrew sash lock.

3. Remove the screws installed through the frame and

frame lock.

4. Close (slide) the side panels into frame.

5. Keeping a firm grip on air conditioner, raise the sash

and carefully “rock” air conditioner backward to drain

any condensate water in base of unit. Be careful not to

spill any remaining water while lifting unit from window.

6. Store parts WITH the air conditioner in the box

FIG. 13

USING YOUR AIR CONDITIONER

Electronic Control Panel & Remote Control

1. Power Button: Turns the air conditioner on and

off

2. Digital Display: Displays the current room tem-

perature or the amount of time left on the timer.

Shows the Set Temp when setting the tempera-

ture. Shows the Timer Set when setting the timer.

The once the timer and/or temperature are set,

the display will change to show the current room

temperature. To see the set temperature again,

simply press either of the Temp/Delay ▲/▼

buttons.

3. Temperature Set: Use these buttons on the con-

trol panel and remote to increase or decrease the

Set Temperature (the desired room temperature)

in cooling or energy saver mode. The SET light

will light up when setting the temperature

4. Timer Set: Use these buttons on the control

panel and remote to set the Timer. Each press of

the Timer (DELAY) buttons will increase or de-

crease the timer. For timer instructions see #7.

5. Fan Speed & Auto Fan: Use the fan speed but-

tons to change the fan speed. Choose between

low, medium, high, and Auto. When using the re-

mote control, press the AUTO button to turn auto

mode on and the FAN+ and FAN– buttons to

select low, medium, or high fan speed.

6. Mode Button: Press the mode button to cycle

through the various modes: Cooling, Energy

Saver, and Fan only.

7. Auto-on Timer: When the air conditioner is off, it

can be set to automatically turn on in 1-24 hours

at the previous set mode and fan setting. To set

the Auto-on Timer, press the DELAY button on

the unit or remote control. Each touch of the ▲/▼

on the unit or the +/- buttons on the remote will

change the timer setting in 1 hour intervals. The

SET light will turn on while setting.

Auto-off Timer: When the air conditioner is on, it

can be set to automatically turn off in 1-24 hours.

To se the Auto-off Timer, press the DELAY button

on the unit or remote control. Each ouch of the ▲/

▼on the unit or the +/- buttons on the remote will

change the timer setting in 1 hour intervals. The

SET light will turn on while setting.

• To see the remaining time, press the DELAY

Button. To change the timer setting use the

▲/▼on the unit or the +/- buttons on the

remote.

• To cancel the timer, press the DELAY button

until the SET light turns off.

Air Conditioner Controls

Remote Control

This display always shows the room

temperature except when setting

the Set temperature or the Timer.

When the light is on the unit is in

temperature or timer set mode.

Light Indicates the

Timer is set.

Timer Increase

Auto Fan On

Increase Fan Speed

Power Button

1-24Hr Timer

Timer

Decrease

Mode Button

Decrease

Fan Speed

Increase/

Decrease

Temperature

Normal Operating Sounds

• You may hear a pinging noise caused by water

hitting the condenser, on rainy days, or when the

humidity is high. This design feature helps re-

move moisture and improve efficiency.

• You may hear the thermostat click when the com-

pressor cycles on and off.

• Water will collect in the base pan during rain or

days of high humidity. The water may overflow

and drip from the outside part of the unit.

• The fan may run even when the compressor is

not on.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Soleus Air Klimaanlage Handbücher

Soleus Air

Soleus Air MA-9000AH Bedienungsanleitung

Soleus Air

Soleus Air LX-140 Bedienungsanleitung

Soleus Air

Soleus Air MA-9000AH Bedienungsanleitung

Soleus Air

Soleus Air WM1-05M2-01 Bedienungsanleitung

Soleus Air

Soleus Air PH4-10R-01 Bedienungsanleitung

Soleus Air

Soleus Air KFHHP-22-ID Technisches Datenblatt

Soleus Air

Soleus Air PSR-06-01 Bedienungsanleitung

Soleus Air

Soleus Air SG-PAC-12E1 Bedienungsanleitung

Soleus Air

Soleus Air 000 BTU Evaporative Portable Air Conditioner and... Bedienungsanleitung

Soleus Air

Soleus Air PH4-13R-01 Bedienungsanleitung

Soleus Air

Soleus Air MAC-8000 Bedienungsanleitung

Soleus Air

Soleus Air WM1-06E-01 Bedienungsanleitung

Soleus Air

Soleus Air PE1-09R-30 Bedienungsanleitung

Soleus Air

Soleus Air TTW-SLG Bedienungsanleitung

Soleus Air

Soleus Air TTWM1-10-01 Bedienungsanleitung

Soleus Air

Soleus Air TTWM1-10-01 Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-18HCE Bedienungsanleitung

Soleus Air

Soleus Air WM1-05M-01 Bedienungsanleitung

Soleus Air

Soleus Air TM-PAC-08E3 Bedienungsanleitung

Soleus Air

Soleus Air iCongo PSQ-08-01 Bedienungsanleitung

Soleus Air

Soleus Air LX-140BL Bedienungsanleitung

Soleus Air

Soleus Air GM-WAC-15ESE-C Bedienungsanleitung

Soleus Air

Soleus Air LX-140 Bedienungsanleitung

Soleus Air

Soleus Air Soleus LX-100 LX-100 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung

Carrier

Carrier 42HVM109303 Bedienungsanleitung