Soleus Air SG-WAC-15ESE Bedienungsanleitung

Electronic Window Air Conditioner

Operating Instructions

Models

SG-WAC-15ESE

SG-WAC-18ESE

SG-WAC-25ESE

Thank you for choosing a Soleus Air powered by Gree Air Conditioner. This owner’s manual will

provide you with valuable information necessary for the proper care and maintenance of your new

product. Please take a few moments to thoroughly read the instructions and familiarize yourself with

all the operational aspects of your new air conditioner.

For your own records, please attach a copy of your sales receipt to this manual. Also, write the store

name/location, date purchased, and serial number below:

Store Name: ____________________________________________________

Location: ______________________________________________________

Date Purchased: _________________________________________________

Serial Number (located on back of unit): ______________________________

IMPORTANT SAFETY INSTRUCTIONS

Before installing and using your air conditioner, please read this owner’s manual carefully. Store this

manual in a safe place for future reference. Your safety and the safety of others is very important to

us. Please pay attention to all safety messages outlined in this owner’s manual.

WARNING: To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow

the following basic precautions:

This is a safety alert symbol.

This symbol alerts you to potential hazards that can harm you or others or even cause

death.

All safety messages will directly follow the safety alert symbol and/or the words

“DANGER” or “WARNING”.

Failure to immediately follow these

instructions may cause serious injury

or even death.

All Safety messages alert you of potential hazards, how to reduce the chance of injury,

and what can happen if instructions are not followed correctly.

• Plug into a grounded 3 prong outlet.

• Do not remove the ground prong.

• Do not use a plug adapter.

• Do not use an extension cord.

• Unplug the air conditioner before servicing

• Use two or more people to move and install the air

conditioner

Wiring Requirement

Recommended Ground Method

For your personal safety, this air conditioner must be grounded. This air conditioner is equipped with a 3 prong power

supply cord with a grounded plug. To minimize the possibility of electrical shock, the cord must be plugged into a 3 prong

outlet and grounded in accordance with all local codes and ordinances. If a 3 prong outlet is not available, it is the cus-

tomer’s responsibility to have a properly grounded 3 prong outlet installed by a qualified electrician.

LCDI Power Cord and Plug

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord and plug as

required by US National Electric Code 440.65. This cord consists of a length of shielded flexible cord with no termination

on the load side and a LCDI attachment plug on the line side.

The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the nominal current

leakage between the cord shield and either load conductor exceeds a predetermined value. The cord will remain de-

energized until the devise has been manually reset. This is intended to reduce the risk of a fire in the power cord or

combustible materials nearby. The cord shields are not grounded and they must be considered a shock hazards if

exposed. The cord shield must not be connected to ground or to any exposed metal.

The test and reset buttons on the LCDI Plug are used to check if

the plug is functioning properly. To test the plug:

1. Plug power cord into a wall outlet

2. Press the TEST Button, the circuit should trip and cut all

power to the air conditioner

3. Press the RESET button for use

If a test is performed and the indicator light remains ON, the

current leakage has been detected. Do not use the air

conditioner or attempt to reset the LCDI Plug. Contact Customer

Service for troubleshooting recommendations.

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove the ground prong.

Do not use an adapter

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock

The electrical ratings for your air conditioner are listed on the model and serial

number label located on the front left side of the unit (when facing the front).

Specific electrical requirements are listed in the chart below. Follow the

requirements below for the type of plug on the power supply cord.

Power Supply Cord

It is the customer’s responsibility:

• To contact a qualified electrician

• To assure that the electrical installation is adequate

and in conformance with the National Electrical Code,

ANSI/NFPA 70 - latest edition, and all local codes and

ordinances.

Copies of the standards listed may be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, Massachusetts 02269

208~230 Volt (197.2 min. - 253 max.)

0-20 amps

20-amp time-delay fuse or

Use on single outlet circuit only

PARTS LIST

(on 25ESE models)

SEAL-BOTTOM RAIL TO UNIT

SIDE RETAINER

FRAME

ASSEMBLY

(LEFT)

WASHER HEAD

LOCKING SCREW

FOAM GASKET

TOP ANGLE

FRAME

ASSEMBLY

(RIGHT)

SAFETY LOCK AND

3/4"ROUND-HEAD

SCREW

1/2" LONG

SCREWS AND

LOCKNUTS

LOCKNUT

3/4" LONG

FLAT HEAD

BOLT

WINDOW SUPPORT

BRACKET

WINDOW SASH SEAL

SILLANGLE

BRACKET

TOOLS NEEDED

Large Flathead Screwdriver

Tape Measurer

Adjustable Wrench or Pliers

Pencil

Level

Socket Wrenches

Phillips Head Screwdriver

25ESE 15/18ESE

Non-Hardware Packing List

• Window Air Conditioner

• AAA Batteries (2) & Remote Control

• Top Mounting Rail

• Foam Top Mounting Rail Seal Strip

• Accordion Panels (2)

• Side Retainer (2)

• Window Sash Seal

• Foam Seal for Bottom Rail

• Owner’s Manual

25ESE 15/18ESE

7/8

ROUND HEAD

SPECIFICATIONS

• Noise level is measured at a distance of 3.28 ft away from the front of the unit in cooling mode.

• Power consumption is measured when the fan runs at the highest speed setting.

• These specifications are for reference only. For actual data, please refer to the rating label on the unit.

Model SG-WAC-15ESE

Power Supply (Ph/V/Hz) 1/115/60Hz

Dehumidifying Capacity (Pints/Day) 91.2

Rated Cooling Capacity (BTU/h) 15,000

Rated Heating Capacity (BTU/h) /

Cooling Power Input (Watts) 1400

Heating Power Input (Watts) /

Rated Current Cooling (Amperage) 12

Rated Current Heating (Amperage) /

EER/C.O.P 10.8

Noise Level db (A) Indoor/Outdoor 58/64

CFM 480

Design Pressure (PSIG) (H/L) /

Dimensions (W” x H” x D”) 23.63 x 17.78 x 25.44

Package Dimensions (W” x H” x D”)28.28 x 19.97x 26.09

Net/Gross Weight (Lbs) 110/129

Refrigerant Charge (Oz) 28.22

SG-WAC-18ESE

1/230-208/60Hz

129.6

18,000 /17,600

1680 /1650

8.1/8.8

10.7

59/64

480

23.63 x 17.78x 25.44

28.28 x19.97 x 26.09

110/125

28.75

SG-WAC-25ESE

1/230-208/60Hz

192

24,500/24,000

2600 /2550

11.6/12.6

9.4

59/64

400-490

26.54x 18.62x26.30

28.94x 20.1 x 31.69

135/152

40.56

INSTALLATION & ASSEMBLY INSTRUCTIONS

Window Preparation

Please read all instructions prior to installing your air conditioner. Two people are recommended to install this product. If

a new electrical outlet is required, have the outlet installed by a qualified electrician before installing the unit.

Before installing the unit, check the dimensions of your window to make sure the air conditioner will fit. This unit is made

to fit inside a standard double-hung window. Make sure the window is in good shape and able to firmly hold the needed

screws. If not, make repairs prior to installing the unit.

Storm Window Requirements

A storm window frame will not allow the air conditioner to tilt properly which in turn will keep it from draining properly. To

adjust for this, attach a board or piece of wood to the sill. The board or wood piece should have a depth of at least 1 1/2”.

Make sure the board or piece of wood is approximately 1/2” higher than the storm window frame. This will allow the air

conditioner to tilt enough for proper drainage. (See FIG. 1).

Prior to Installing the Air Conditioner

1. Check for anything that could block airflow. Check the area outside of the window for things such as shrubs, trees, or

awnings. Check the inside area to make sure curtains, drapes, or blinds will not prevent proper airflow.

2. Check the available electrical outlet. The power supply must be the same as shown on the unit serial nameplate

(located on the left side of the unit, near the front faceplate). Be sure the outlet is close enough for the power cord to

reach.

3. Carefully unpack the air conditioner. Remove all packing material and make sure the floor is protected when remov-

ing. Due to the large size of this air conditioner, two people should move the unit together.

Model SG-WAC-25ESE SG-WAC-15ESE / SG-WAC-18ESE

Unit Height 18 5/8” 17 5/8”

Unit Width 26 1/2” 23 1/2”

Min. Window Opening 19” 18 1/2”

Min. Window Width 31” 26 1/2”

Max Window Width 43” 40 1/2”

SASH

1 1/2” MIN

(38 mm)

STORM

WINDOW

FRAME

Board or wood

piece must be

approximately

1/2” higher

than the storm

window frame

for proper

drainage

FIG. 1

When handling the unit, be careful to avoid cuts from

the sharp metal edges and aluminum fins on the front

and rear coils.

INSTALLATION & ASSEMBLY INSTRUCTIONS - WINDOW MOUNTING

REMOVE CHASSIS

1. Pull down the front panel and remove the filter (FIG. 1 below)

2. Lift the front panel upwards to remove and place to the side.

3. Locate the four faceplate screws and remove. These screws will need to be re-installed prior to mounting the air con-

ditioner (FIG. 2 above)

4. After removing the screws, gently pull away the faceplate from the air conditioner cabinet (FIG. 3 & 4).

5. Remove the shipping screws from the top of the unit (SG-WAC-25ESE only) and both sides of the cabinet if in-

stalled.

6. Remove the two screws on the top of the chassis that hold the cabinet to the unit. Hold the cabinet while pulling on

the base of the chassis and remove the chassis from the cabinet (FIG. 5).

7. Add two foam inserts to the holes on top of the cabinet where the shipping screws were located.

8. There may be internal packing protection on the SG-WAC-25ESE. This packing material must be removed prior to

installation (FIG. 6)

FIG. 2

FIG. 1

FIG. 3 FIG. 4

FIG. 6

FIG. 5

ASSEMBLY & INSTALLATION (CONT.)

4. Install top angle side to cabinet as shown in FIG. 7.

5. Slide "I" section of window filler panel into side retainer.

Do both sides.

WINDOW FILLER PANEL

WINDOW FILLER

PANEL

SIDE RETAINER

FIG. 8a

FIG. 7

Foam Gasket and Top

Angle Rail

Top Angle Rail and Side Bracket Installation

1. Place the air conditioner on a hard flat surface.

2. Locate the foam gasket and top angle rail

3. Attach the foam gasket to the top angle rail.

7. Install side retainer to cabinet as shown in

FIG.8b-9.

(see FIG 8b-9)

. Insert top and bottom legs of window filler panel frame

into channel in the top

angle and bottom rail. Do both

sides

FIG.8b

PLASTIC

FRAME

WINDOW FILLER

PANEL

SIDE RETAINER

8. Once the window panelsarecorrectly installed, for 25K

insert the washer head locking screws on the top rail and

frame. Do not tighten all the way at this time. Allow the

bottom frame to slide freely.

Placing the Cabinet Inside the Window

1. Open the window and place the cabinet in the middle

of the window sill.

2. Make sure the bottom rail is seated over the window

sill as shown below. Bring the window down temporar-

ily behind the top angle rail to hold the cabinet in place.

3. Fasten cabinet to window sill using two 7/8” Round-

head screws (3/4” ROUND-Head screws on SG-WAC-

25ESE). Pre-drill holes if needed. Add the bottom rail

seal over the screws.

FIG. 9

TOP VIEW

SILL

BOTTOM

RAIL

ROUND-HEAD SCREW

3/4"for 25ESE

7/8"for 15/18ESE

ASSEMBLY & INSTALLATION (CONT.)

Install Support Brackets

1. Hold each support bracket flush against the outside of

the window sill. Tighten each bracket to the bottom of

the cabinet as shown below. Mark the brackets at top

lever of the window sill and then remove.

2. Assemble the sill angle brackets to the support brack-

ets at the marked position as shown above. Hand

tighten, but not all the way for any changes that may

need to be made later during installation.

3. Install the support brackets (with sill angle brackets

attached) to the bottom of the cabinet as shown below.

4. Tighten all 6 bolts securely.

Mark

Left

Right

1/2” Long Screws

and Locknuts

Sill Angle

Bracket

Flat Head Bolt

Locknut

1/2” long

screw and

locknuts

Extend the Accordion Panels

1. Carefully raise the window to expose the accordion

panel and panel frame. Loosen the locking screws so

the accordion panels slide easily.

2. Extend each panel to completely fill the width of the

3. Close window behind top angle.

Set a locking screw on both sides of the curtain as shown.

window. Tighten the locking screws when the panels

are fully extended.

Install the Window Lock and Sash Seal

1. Trim the sash seal to fit the width of the window. Insert

the sash seal into space between the upper and lower

sashes.

2. Attach the right angle safety lock as shown below.

Locking Screw

For 24K

3/4" Round-

Head Screw

for 14/18K

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Soleus Air Klimaanlage Handbücher

Soleus Air

Soleus Air PE2-09R-32 Bedienungsanleitung

Soleus Air

Soleus Air SG-PAC-10E5 Bedienungsanleitung

Soleus Air

Soleus Air PE3-12R-03 Bedienungsanleitung

Soleus Air

Soleus Air SPTAC-09H Bedienungsanleitung

Soleus Air

Soleus Air 000 BTU Evaporative Portable Air Conditioner and... Bedienungsanleitung

Soleus Air

Soleus Air KFHIP-09-OD Technisches Datenblatt

Soleus Air

Soleus Air TTW-SLG Bedienungsanleitung

Soleus Air

Soleus Air PH1-14R-03 Bedienungsanleitung

Soleus Air

Soleus Air air-condition Bedienungsanleitung

Soleus Air

Soleus Air 000/12 - BTU Multi-Room Heat/Cool Room Air... Bedienungsanleitung

Soleus Air

Soleus Air PH5 Series Bedienungsanleitung

Soleus Air

Soleus Air TM-PAC-08E3 Bedienungsanleitung

Soleus Air

Soleus Air WS1-05M2-02 Bedienungsanleitung

Soleus Air

Soleus Air KY-32H Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-18HCE Bedienungsanleitung

Soleus Air

Soleus Air PE6-10R-03 Bedienungsanleitung

Soleus Air

Soleus Air GM-WAC-25ESE-C Bedienungsanleitung

Soleus Air

Soleus Air HCC-C09HP-A Bedienungsanleitung

Soleus Air

Soleus Air PS08-01 Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-15ESE-C Bedienungsanleitung

Soleus Air

Soleus Air PH4-10R-01 Bedienungsanleitung

Soleus Air

Soleus Air WCM1-08E-01 Bedienungsanleitung

Soleus Air

Soleus Air WS4-06EW-201 Bedienungsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung

Carrier

Carrier 42HVM109303 Bedienungsanleitung