Soleus Air SG-CAC-08ESE Bedienungsanleitung

Electronic Casement Window Air Conditioner

Operating Instructions

Model

SG-CAC-08ESE

SG-CAC-10SE

SG-CAC-12SE

Thank you for choosing a Soleus Air powered by Gree Air Conditioner. This owner’s manual will

provide you with valuable information necessary for the proper care and maintenance of your new

product. Please take a few moments to thoroughly read the instructions and familiarize yourself with

all the operational aspects of your new air conditioner.

For your own records, please attach a copy of your sales receipt to this manual. Also, write the store

name/location, date purchased, and serial number below:

Store Name: ____________________________________________________

Location: ______________________________________________________

Date Purchased: _________________________________________________

Serial Number (located on back of unit): ______________________________

IMPORTANT SAFETY INSTRUCTIONS

Before installing and using your air conditioner, please read this owner’s manual carefully. Store this

manual in a safe place for future reference. Your safety and the safety of others is very important to

us. Please pay attention to all safety messages outlined in this owner’s manual.

WARNING: To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow

the following basic precautions:

This is a safety alert symbol.

This symbol alerts you to potential hazards that can harm you or others or even cause

death.

All safety messages will directly follow the safety alert symbol and/or the words

“DANGER” or “WARNING”.

Failure to immediately follow these

instructions may cause serious injury

or even death.

All Safety messages alert you of potential hazards, how to reduce the chance of injury,

and what can happen if instructions are not followed correctly.

• Plug into a grounded 3 prong outlet.

• Do not remove the ground prong.

• Do not use a plug adapter.

• Do not use an extension cord.

• Unplug the air conditioner before servicing

• Use two or more people to move and install the air

conditioner

SPECIFICATIONS

• Noise level is measured at a distance of 3.28 ft away from the front of the unit in cooling mode.

• Power consumption is measured when the fan runs at the highest speed setting.

• These specifications are for reference only. For actual data, please refer to the rating label on the back of the unit.

Model SG-CAC-08ESE

Power Supply (Ph/V/Hz) 1/115/60

Dehumidifying Capacity (Pints/Day) 31.2

Rated Cooling Capacity (BTU/hr) 8,000

Cooling Power Input (Watts) 762

Rated Current Cooling (Amperage) 6.6

Cooling EER 10.5

Noise Level dB(A) (High/Med/Low) 56/54/52

CFM (High/Med/Low) 450/410/370

Power Plug Type NEMA 5-15P

Product Dimensions

(W” x D” x H” ) (Inches)

14.2” x 24.5” x 20.3”

Product Weight (Lbs) 72.8

Refrigerant R-410A

SG-CAC-10SE

1/115/60

10,000

1052

9.2

9.5

60/58/56

550/510/470

NEMA 5-15P

14.2” x 24.5” x 20.3”

TBA

R-410A

SG-CAC-12SE

1/115/60

38.4

12,000

1263

9.5

60/58/56

550/510/470

NEMA 5-15P

14.2” x 24.5” x 20.3”

TBA

R-410A

Energy Star Yes No No

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions before using this air conditioner

These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash, or installation in a

metal CASEMENT window. Modification may be necessary when installing in windows made differently than those

shown in these instructions.

MEETING ELECTRICAL REQUIREMENTS

OBSERVE ALL LOCAL GOVERNING CODES AND ORDINANCES.

DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE POWER SUPPLY CORD GROUNDING PRONG.

NOTE: If codes permit, and a separate grounding wire is used; it is recommended that a qualified electri-

cian determine that the grounding path is adequate and not interrupted by plastic, non-metallic gas-

kets, or other insulating materials.

RECEPTACLE WIRING

Receptacle wiring should be a minimum of 14 gauge. Use copper wire only. It is your responsibility to provide proper and

adequate receptacle wiring, installed by an electrician.

ELECTRICAL REQUIRMENTS

A 115 volt (103.5 minimum, 126.5 maximum), 60 Hertz, AC only, 15 ampere fused electrical supply is required. A time

delay fuse or time delay circuit breaker is also required. A separate circuit, serving only this appliance, MUST be pro-

vided.

WARNING: Electrical Shock and Personal Injury Hazard

• Electrical ground is required on this appliance.

• DO NOT ground to a gas line.

• If a cold water pipe is interrupted by plastic, non-metallic gaskets, or other insulating materials, DO NOT use for

grounding.

• Check with a qualified electrician if you are in doubt as to whether the appliance is properly grounded.

• DO NOT modify the power supply cord plug. If it does not fit the outlet, have the correct outlet installed by a qualified

electrician.

• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral, or grounding circuit could result in an

electrical shock.

• DO NOT use an extension cord with this appliance.

Failure to follow these instructions could result in electrical shock, serious injury or death.

ELECTRICAL CONNECTION

Electrical ground is required on this appliance.

Recommended grounding method:

For your personal safety, this appliance must be grounded. This air

conditioner includes a power supply cord with a 3-prong grounding

plug. To minimize possible electrical shock:

• The cord must be plugged into a mating 3-prong grounding-type

wall receptacle.

• Must be grounded in accordance with National Electrical Code

(ANSI/NFPA 70—Latest version) and

• All local codes and ordinances

If a mating 3-prong grounding-type receptacle is not available, it is the

responsibility of the consumer to have a properly grounded 3-prong

wall receptacle installed by a qualified electrician.

PREPARING FOR INSTALLATION

Installation Tips

For wood-frame casement windows: It may be necessary to construct a frame, using at least 1-inch thick wood, with a

15-1/2-inch wide opening.

For brick or cement building construction: It may be necessary to put a wood stool strip under AC, for mounting pur-

poses.

Tools Required:

• Flat-head screwdriver

• Phillips-head screwdriver

• Carpenter's level

• Tape measure

• Fine tooth saw

• Electric or hand drill

• Knife and scissors

• Pencil

DISCLAIMER

ALL INFORMATION AND THE TECHNICAL SPECIFICATIONS PRESENTED IN THIS USER’S MANUAL ARE THE

PRESENTATION OF THE MANUFACTURER. SOLEUS INTERNATIONAL HAS NOT CONDUCTED INDEPENDENT

TEST TO THE INFORMATION AND THE SPECIFICATIONS PRESENTED HEREWITHIN.

PREPARING FOR INSTALLATION

WARNING: Failure to adhere to the following precautions could result in personal injury and product

damage.

• Because this unit weighs about 88 to 105 pounds, it is recommended that you have someone help you when install

your new unit, and that you both use proper lifting techniques.

• Inspect the condition of the window where unit will be installed. Be sure it will support the weight of the unit.

• This appliance must be installed according to all applicable codes and ordinances.

• Handle AC with care. AVOID sharp metal fins on front and rear coils.

• Make sure your AC does not fall during installation.

• Do not use water collected in the unit for drinking. It is not sanitary.

PARTS LIST & INSTALLATION

INSTALLATION

INSTALLING THE UNIT IN A SLIDING WINDOW

1. Attach support brace to platform as shown.

Use adjustment bolt and hex flange nut to complete

assembly. Choose slot and adjustment bolt hole

locations that will create a 45 degree angle between

platform and support brace. Try assembly in the

window to determine if platform will rest properly, and

allow proper slope (3/16-inch lower on outside).

NOTE: If you are planning to use a siding protection

board (see Step 5) on the outside of your

house, hold board in place when testing assembly in

window.

2. Measure, and lightly mark a line 8-11/16 inches

from window jamb.

NOTE: If any sash stop protrudes more than 1

inch from the side window jambs, the 8-11/16-inch

measurement must be increased accordingly.

Screen and storm window frames may also require

adjustments to the measurement.

3. Center platform assembly on the line with inside

platform tab pressed against inside edge of window

track. Using the holes in the platform as a guide,

mark and drill two 9/64-inch diameter holes. Drill

holes in either track or stool.

CAUTION

Property Damage Hazard—Failure to adhere

to the following precautions could result in

damage to window or the air conditioner. Make

sure the wood stool or window track is securely

attached to the building construction. Use

longer screws in sub-framing if necessary.

INSTALLATION—SLIDING

INSTALLING THE UNIT IN A SLIDING WINDOW (CONT.)

4. Peel off protective backing from track seal. Apply

seal to room side of window track. Center of seal strip

should coincide with the line marked in Step 2. The

two screw holes drilled in Step 3 should be directly

above seal strip in the inner track.

5. Securely attach a siding-protection board to

side of house.

NOTE: Siding-protection board should be long

enough to span 2 wall studs.

6. Place platform assembly, with platform tab

against inside of window track, and attach it to

window jamb. Use appropriate length screws (Items

9-11 in Preparing For Installation).

7. Adjust platform assembly so that outside edge is

3/16-inch lower than inside edge, as shown right.

This ensures proper water drainage from the air

conditioner.

8. Level platform assembly from side-to-side.

Also, make sure window track is level. Use leveling

shims as necessary to ensure unit is level from side-to-

side.

9. Measure height of window opening from top of

platform assembly as shown right. Subtract 20-5/8

inches. Mark this measurement on plastic window

panel, along the longer side. (continued)

INSTALLATION—SLIDING

INSTALLING THE UNIT IN A SLIDING WINDOW

(CONT.)

10. Clamp plastic window panel between a board

and a work table, and cut along cutting line with a fine

tooth saw. Remove any burrs with a file.

11. Fasten side channels to the sides of the AC

using 3 screws (Item 17) per channel. Start with first

screw at top of channel. Make sure hook ends of

channels face toward back of unit.

12. Slide plastic window panel into panel frame,

with the smooth side to the room. Slide panel frame

assembly into side channels of the AC cabinet. Make

sure plastic window panel is firmly enclosed on all

sides by the retainer grooves.

13. Cut side channel seal into 2 equal lengths.

Remove protective backing and apply it to the rear

side of cabinet side channels, starting just below

panel frame assembly. Pinch off excess length so

seal is even with the bottom of the cabinet side

channel.

14. To remove front

1. Remove the two front retaining screws from the

front frame.

2. Press firmly on each side of the metal case close

to the front, approximately 2/3 of the way down.

3. While pressing on the sides of the metal case,

gently pull the front out and lift up to release it

from the case.

4. Then remove the four screws from the front frame

to release the control panel box.

NOTE: DO NOT push or pull air direction louvers.

15. Place AC in window opening. As shown right, it

should sit on platform assembly so that window panel

frame, and cabinet side channels are against top and

side window jambs. (continued)

INSTALLATION—SLIDING

INSTALLING THE UNIT IN A SLIDING WINDOW (CONT.)

16. Slide inner window sash firmly against side

of the cabinet. Make sure not to peel the seal strips

from the window track and cabinet side channels. If

the panel frame does not fit snugly to the inner

window sash, secure the panel frame to the sash

with #8x3/4-inch screws, or #8-32x3/4-inch self-

threading screws. Use the partially plugged holes in

the panel frame. Drill 1/8-inch pilot holes for the

screws.

17. Hook the safety bracket over the base of the

unit and fasten it to the front of the platform

assembly. Use a #8-32x3/4-inch self-threading

screw.

NOTE: The bracket prevents movement of the

air conditioner (either in or out) after completing the

installation.

18. Stuff the foam seal strip/sash seal between

the vertical sash and the window glass, as shown

right.

19. Use the window locking bracket to lock the

inner window sash to the base of the outer window

sash. Use one #8x3/4-inch screw, or #8-32x3/4-

inch self-threading screw. (Drill 1/8-inch pilot hole).

20. To replace the front

First reconnect the coupler plugs, make the exhaust

control positioned through the front in the proper

location. Gently push the front into position on the

cabinet. It should click into place. Then replace the

retaining screws that holds the panel in place.

Do not push or pull the front panel louvers.

Alternate Window Jamb Applications

To install in windows having no flanges or wood stops

on the top and side jambs, the channels and panel

frame must fit against a mating flange (or 1/16-inch

max. thick angle) attached to the window jambs.

Figure A shows this angle installed. Figures B & C

show alternate treatments. On the sash side of the

opening, the leading corner of the inner sash

becomes the flange. You can purchase the angle

Strip locally.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Soleus Air Klimaanlage Handbücher

Soleus Air

Soleus Air SG-WAC-25ESE-C Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-06ESE-C Bedienungsanleitung

Soleus Air

Soleus Air HCC-C09H26-A Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-10ESE-C Bedienungsanleitung

Soleus Air

Soleus Air TTWM1-10-01 Bedienungsanleitung

Soleus Air

Soleus Air PSH-08-01 Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-15ESE-C Bedienungsanleitung

Soleus Air

Soleus Air KY-32U Bedienungsanleitung

Soleus Air

Soleus Air PSR-06-01 Bedienungsanleitung

Soleus Air

Soleus Air SG-WAC-10ESE-F Bedienungsanleitung

Soleus Air

Soleus Air PE6-10R-03 Bedienungsanleitung

Soleus Air

Soleus Air PSC-12HP-201 Bedienungsanleitung

Soleus Air

Soleus Air SG-PAC-10E2 Bedienungsanleitung

Soleus Air

Soleus Air LX-140 Bedienungsanleitung

Soleus Air

Soleus Air 3046364 Bedienungsanleitung

Soleus Air

Soleus Air MAC-12K/10K Bedienungsanleitung

Soleus Air

Soleus Air GM-PAC-10E2 Bedienungsanleitung

Soleus Air

Soleus Air KFHHP-09-OD Technisches Datenblatt

Soleus Air

Soleus Air PE4-11R-03 Bedienungsanleitung

Soleus Air

Soleus Air KFHHP-18 Bedienungsanleitung

Soleus Air

Soleus Air KY-120HP Bedienungsanleitung

Soleus Air

Soleus Air LX-140 Bedienungsanleitung

Soleus Air

Soleus Air PE2-07R-62 Bedienungsanleitung

Soleus Air

Soleus Air KFCHP5-09-ID Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung

Carrier

Carrier 42HVM109303 Bedienungsanleitung