Solinst 464 250 psi Gebrauchs- und Pflegehandbuch

Control Unit Solenoid Valve Assembly Replacement

High Quality Groundwater and Surface Water Monitoring Instrumentation

(Page 1 of 2)

Model 464 250 psi (sold after September 2013)

®Teﬂon is a registered trademark of DuPont Corp. Continued on page 2...

Tools and Materials Needed

1. 464 Solenoid Valve Assembly - 250 psi (Spare) (#111743)

2. 3/32" Allen Key

3. Small Utility Knife

4. 7/64" Allen Key

5. 11/16" Wrench

6. 14 mm Wrench

7. 1/2" Wrench

8. 7/16" Wrench

9. Teﬂon®Tape

10.Any suitable plastic adhesive (e.g. silicone)

Instructions

1. Turn the Control Unit off and remove the batteries.

2. Use the 3/32" Allen key to undo the four hex screws on the sides

of the Control Unit.

Hex

Screws

Hex

Screws

3. Remove the panel from the Control Unit and ﬂip it over to access

the Solenoid Valve Assembly.

Panel

4. Push down on the ﬁttings to remove the three black tubes from the

Shuttle Valve Assembly, and the two clear tubes from the Solenoid

Valve Assembly (photo shows black tubes removed).

Solenoid Valve

Assembly

5. Use the 7/64" Allen Key to remove the three screws from the

bracket holding the Shuttle Valve Assembly, and carefully slide the

Shuttle Valve Assembly out from the bracket.

464 Solenoid Valve Assembly - 250 psi (Spare)

Shuttle Valve

Assembly

Remove

Tubes

Bracket

Remove

Tube

Remove

Tubes

Printed in Canada

October 8, 2014

(#111742)

(Page 2 of 2)

For further information contact: Solinst Canada Ltd.

Fax: +1 (905) 873-1992; (800) 516-9081 Tel: +1 (905) 873-2255; (800) 661-2023

35 Todd Road, Georgetown, Ontario Canada L7G 4R8

Web Site: www.solinst.com E-mail: [email protected]

6. Use a small utility knife to break any adhesive holding the Solenoid

Connector to the Circuit Board. Unplug the Solenoid Connector

from the Circuit Board.

7. Use the appropriate wrenches to remove the two ﬁttings (shown

above) from the Shuttle Valve Assembly. Twist to remove the

Solenoid Valve Assembly from the Shuttle Valve Assembly.

Plugs

Plug

®Solinst is a registered trademark of Solinst Canada Ltd.

Unplug

Solenoid

Connector

9. Remove the three plugs from the new Solenoid Valve Assembly.

8. Use the appropriate wrenches to remove the three ﬁttings from the

old Solenoid Valve Assembly.

10. Screw the three ﬁttings back into the new Solenoid Valve Assembly.

11 Screw the new Solenoid Valve Assembly into the Shuttle Valve

Assembly. Screw the two ﬁttings back into the Shuttle Valve

Assembly (see photo at left for proper connections).

12. Plug the Solenoid Connector back into the Circuit Board, and

apply a small amount of adhesive to the outside of the Connector

to help secure it to the Circuit Board.

13. Slide the Shuttle Valve Assembly back into place under the bracket

and secure it using the three screws.

14. Push the three black tubes back into the ﬁttings on the Shuttle Valve

Assembly. Use the photo below to ensure correct connections.

15. Push the clear tubes into the ﬁttings on the new Solenoid Valve

Assembly. Use the photo below to ensure correct connections.

16. Place the panel in the Control Unit case and reinstall the four hex

screws.

17. Reinstall the batteries. Test the Control Unit to ensure proper

connections were made when replacing the Solenoid Valve

Assembly.

Note: Wrap new Teﬂon tape around the threads of all the ﬁttings.

Solenoid Valve

Assembly

Shuttle Valve

Assembly

CYL Port

IN Port

Andere Solinst Steuereinheit Handbücher

Solinst

Solinst 464 Mk3 250 psi Gebrauchs- und Pflegehandbuch

Solinst

Solinst 464 125 psi Gebrauchs- und Pflegehandbuch

Solinst

Solinst 464 Mk3 250 psi Gebrauchs- und Pflegehandbuch

Solinst

Solinst 464 Bedienungsanleitung

Solinst

Solinst 464 250 psi Konfigurationshandbuch

Solinst

Solinst 464 Mk3 Bedienungsanleitung

Solinst

Solinst 464 125 psi Konfigurationshandbuch

Solinst

Solinst 464 Betriebsanleitung

Solinst

Solinst 464 250 psi Gebrauchs- und Pflegehandbuch

Solinst

Solinst 464 125 psi Gebrauchs- und Pflegehandbuch

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung