Solinst 464 Mk3 250 psi Gebrauchs- und Pflegehandbuch

Controller Board Assembly Replacement

Model 464 Mk3 250 psi

High Quality Groundwater and Surface Water Monitoring Instrumentation

(Page 1 of 2)

Tools and Materials Needed

1. 464 Mk3 250 psi Controller Board Assembly (#113871)

(Includes Circuit Board and LCD)

2. 3/32" Allen Key

3. 3/16" Nut Driver

4. Needle Nose Pliers

Instructions

1. Turn the Pump Control Unit off and remove the batteries.

2. Use the 3/32" Allen key to undo the four hex screws on the sides

of the Control Unit.

Hex

Screws

Hex

Screws

Panel

3. Remove the panel from the Control Unit and ﬂip it over to access

the controller board assembly.

®Solinst is a registered trademark of Solinst Canada Ltd.

Controller Board

Assembly

4. To gain better access to the controller board, disconnect any

tubing that may be in the way. To remove the tubing, push on the

“grasping ring” of the black tubing ﬁtting (to release tubing) and pull

the tubing out. Remember where the tubing was connected.

Disconnect Tubing

Solenoid Connector Battery Connector

Solenoid Assembly

5. Pull to remove the battery connector and solenoid connector from

the circuit board.

6. Disconnect tubing as required from the solenoid assembly. Pull to

remove the solenoid assembly from the panel. Remember how it

was connected.

7. Press the tabs on the label ribbon cable to unlock and pull it from

the circuit board. You may need to use needle nose pliers.

Label Ribbon Cable

464 Mk3 250 psi Controller Board Assembly (#113871)

Printed in Canada

February 5, 2018

(#113872)

(Page 2 of 2)

For further information contact: Solinst Canada Ltd.

Fax: +1 (905) 873-1992; (800) 516-9081 Tel: +1 (905) 873-2255; (800) 661-2023

35 Todd Road, Georgetown, Ontario Canada L7G 4R8

Web Site: www.solinst.com E-mail: [email protected]

8. Use the 3/16" nut driver to undo the four nuts holding the controller

board assembly in place. Remove any washers. Be careful not to

lose any washers or nuts.

9. Slowly pull to remove the controller board assembly from the back

of the panel. This may take some force as the assembly may be

stuck to the adhesive on the back of the button faceplate label.

10. Leave any washers below the controller board assembly in place on

the mounting screws.

11. Peel any protective plastic from the LCD on the new controller

board assembly.

12. Place the new controller board assembly over the four mounting

screws on the back of the panel. Make sure the controller board

assembly is oriented correctly.

13. Put any washers back over the four screws. Use the nut driver

to tighten the for nuts, securing the controller board assembly in

place.

14. Reconnect the label ribbon cable to the circuit board.

15. Refasten the solenoid assembly to the panel and reconnect any

tubing by pushing into the ﬁttings.

16. Plug the battery and solenoid connectors into the circuit board.

17. Reconnect any other tubing removed by pushing back into the

ﬁttings.

18. Place the panel in the Control Unit case.

19. Reinstall the batteries. Test the Control Unit to ensure proper

connections were made.

20. Reinstall the four hex screws.

Andere Solinst Steuereinheit Handbücher

Solinst

Solinst 464 Mk3 250 psi Gebrauchs- und Pflegehandbuch

Solinst

Solinst 464 Bedienungsanleitung

Solinst

Solinst 464 250 psi Gebrauchs- und Pflegehandbuch

Solinst

Solinst 464 125 psi Gebrauchs- und Pflegehandbuch

Solinst

Solinst 464 250 psi Konfigurationshandbuch

Solinst

Solinst 464 125 psi Konfigurationshandbuch

Solinst

Solinst 464 250 psi Gebrauchs- und Pflegehandbuch

Solinst

Solinst 464 Betriebsanleitung

Solinst

Solinst 464 125 psi Gebrauchs- und Pflegehandbuch

Solinst

Solinst 464 Mk3 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung