Solinst 101 P2 Bedienungs- und Sicherheitshinweise

Connecting Polyethylene Replacement Tape to Reel

High Quality Groundwater and Surface Water Monitoring Instrumentation

(Page 1 of 2)

Model 101 P2

102

Tools and Materials Needed

1. Model 101 P2 Replacement Tape Assembly

• Comes with P2 Probe attached

• 2 Pin Molex Connector

• Grommet

2. Phillips or Robertson Screwdriver

3. Wire Cutters

Instructions

1. Place reel on a ﬂat workbench with faceplate up. Undo the

three screws from the faceplate, and slowly remove it from

the reel.

2. For the Mk1 Model 101 P2, disconnect the Tape Molex

Connector from the Faceplate Molex Connector.

3. For the Mk2 Model 101 P2 Water Level Meters, press down

on the white terminals of the push-release ﬁttings on the

circuit board to remove the tape leads. Remember which

lead is removed from each terminal – this is important

when reconnecting.

Negative

Connector Pin

Note: There is a knot and a black band on the

wire indicating the negative connector pin.

Note: The replacement tape comes with a new grommet.

The old grommet may be replaced with the new one,

or left in if not damaged.

Wires Connected

to Faceplate

Faceplate Molex

Connector

Inside View of Mk1 101 P2 Reel Hub

Showing Tape Connection Detail

Grommet

Black Plastic Bridge

Tape Molex

Connector

Inside View of Mk2 101 P2 Reel Hub

Showing Tape Connection Detail

Grommet

Black Plastic Bridge

Tape Leads

4. Undo the two screws from the black plastic bridge holding

the tape inside the reel hub, and remove the top piece of the

bridge.

5. For the Mk1 Model 101 P2, use the wire cutters to cut the

old Tape Molex Connector from the old tape. Pull the old

tape through the grommet and remove it from the reel.

6. For the Mk2 Model 101 P2 Water Level Meters, simply pull

the old tape through the grommet and remove it from the

reel.

7. Feed the new tape through the grommet into the reel hub.

8. For the Mk1 Model 101 P2, by hand, insert the connector

pins into the new Tape Molex Connector housing. The

negative connector pin is inserted into the terminal on the

pointed side of the Tape Molex Connector housing and the

positive pin into the other terminal.

Printed in Canada

January 3, 2017

(#108708)

(Page 2 of 2)

For further information contact: Solinst Canada Ltd.

Fax: +1 (905) 873-1992; (800) 516-9081 Tel: +1 (905) 873-2255; (800) 661-2023

35 Todd Road, Georgetown, Ontario Canada L7G 4R8

Web Site: www.solinst.com E-mail: [email protected]

9. For the Mk2 Model 101 P2 Water Level Meters, cut the

pins on the tape leads at the point show in the photo below.

Use pliers to ﬂatten the pins against the tape leads, so they

ﬁt into the terminals on the circuit board (see Step 12).

Mk2 101 P2 Tape Connection

Pin inserted into terminal with white

square below it on the circuit board.

10.Position the tape inside the reel hub with black plastic bridge

over top and refasten the two screws to secure the tape to

the reel.

11.For the Mk1 Model 101 P2, connect the Tape Molex

Connector to the Faceplate Molex Connector.

12.For the Mk2 Model 101 P2 Water Level Meters, press

down on the white terminals on the circuit board and insert

the tape leads. Release the terminals and the leads should

be secured. The lead on the bottom of the tape (numbers

facing up) is inserted into the terminal with a white square

below it on the circuit board. See following images.

102

9 8ft 7

13.With the probe in a glass of tap water, turn the Meter

‘ON’. If the buzzer or light do not activate, check the tape

connections.

14.Replace the faceplate on the reel and re-secure the three

screws.

15.Slowly wind the tape onto the reel, holding to ensure no

slack.

Andere Solinst Messgerät Handbücher

Solinst

Solinst 101 SC2000 Bedienungs- und Sicherheitshinweise

Solinst

Solinst 101 Bedienungs- und Sicherheitshinweise

Solinst

Solinst 101B Bedienungsanleitung

Solinst

Solinst 101 Bedienungs- und Sicherheitshinweise

Solinst

Solinst 9700 SolSat 5 Bedienungsanleitung

Solinst

Solinst 107 Leitfaden

Solinst

Solinst 102 Bedienungs- und Sicherheitshinweise

Solinst

Solinst Levelogger 3001 Bedienungsanleitung

Solinst

Solinst 101 Bedienungsanleitung

Solinst

Solinst 101M Bedienungsanleitung

Solinst

Solinst 102M Bedienungsanleitung

Solinst

Solinst 101 P7 SC1000 Bedienungsanleitung

Solinst

Solinst LevelSender 5 Bedienungsanleitung

Solinst

Solinst 101 Bedienungs- und Sicherheitshinweise

Solinst

Solinst 102 Bedienungs- und Sicherheitshinweise

Solinst

Solinst 101 Bedienungs- und Sicherheitshinweise

Solinst

Solinst 101D Bedienungsanleitung

Solinst

Solinst 101 Stücklistenhandbuch

Solinst

Solinst 122M Bedienungsanleitung

Solinst

Solinst 102M Bedienungsanleitung

Solinst

Solinst 101 P7 Bedienungsanleitung

Solinst

Solinst 201 Bedienungsanleitung

Solinst

Solinst 122M Bedienungsanleitung

Solinst

Solinst Levelogger Series Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung