Sony TA-FA30ES Bedienungsanleitung

MICROFILM

SERVICE MANUAL

INTEGRATED STEREO AMPLIFIER

AEP Model

UK Model

E Model

Australian Model

Chinese Model

SPECIFICATIONS

TA-FA30ES

Photo: GOLD model

System

Power Amplifier: Pure-complementary SEPP MOS FET power

amplifier with all stages directly coupled

Preamplifier: Low-noise, high-gain equalizer amplifier

Power section: Large-capacity power supply advanced STD

Rated output

4 ohms, 120 W + 120 W (DIN 0.7%, 1 kHz)

8 ohms, 80 W + 80 W (DIN 0.7%, 1 kHz)

Speaker Impedance

4 to 16 ohms

Output bandwidth (8 ohms)

10 Hz to 100 kHz (at 40 W output, and high-frequency distortion

rate of 0.08%)

Total harmonic distortion

0.008% (at 8 ohms, 10 W output)

Damping factor

100 (8 ohms, 1 kHz)

Intermodulation (1M) distortion (60 Hz : 7 kHz = 4 : 1)

0.008% (8 ohms)

Throughrate

125 V/µ sec, 250 V/µ sec (Inside)

Residual noise

Less than 100 µV (network A)

Equalizer deviation

PHONO MM: 20 Hz to 20 kHz, ± 5 dB

Frequency response

TUNER, CD, AUX, TAPE1/DAT, TAPE2/MD: 7 Hz to

100 kHz dB

S/N

PHONO MC: 78 dB (network A, 0.5 mV)

MM: 95 dB (network A, 5 mV)

TUNER, CD, AUX, TAPE1/DAT, TAPE2/MD: 105 dB

Inputs

Input sensitivity and impedance

PHONO MC: 0.17 mV, 100 ohms

MM: 2.5 mV, 50 kilohms

TUNER, CD, AUX, TAPE1/DAT, TAPE2/MD: 150 mV,

20 kilohms

Maximum input capability (1 kHz)

PHONO MC: 9 mV

MM: 150 mV

Outputs

Output level/impedance

REC OUT 1, 2: 150 mV, 1 kilohm

PHONES: 10 mW (at 8 ohms)

Tone controls

BASS (100 Hz): ± 7 dB

TREBLE (10 kHz): ± 7 dB

General

Power requirements

230 V AC, 50/60 Hz

Power consumption

220 W

Dimensions (approx) (w/h/d)

430 ×150 ×415 mm incl. projecting parts and controls

Mass (approx)

11.0 kg

Supplied accessories

Remote commander (remote ) RM-S326 (1)

Sony batteries R6 (size-AA) (2)

Design and specifications are subject to change without notice.

–3

– 2 –

TABLE OF CONTENTS

1. GENERAL

Location of Controls ....................................................... 3

2. DISASSEMBLY ......................................................... 4

3. ELECTRICAL ADJUSTMENTS......................... 6

4. DIAGRAMS

4-1. Notes for Printed Wiring Boards

and Schematic Diagrams ................................................ 8

4-2. Printed Wiring Boards – INPUT Section – ................... 9

4-3. Schematic Diagram – INPUT Section –......................... 11

4-4. Printed Wiring Boards – MAIN Section – .................... 13

4-5. Schematic Diagram – MAIN Section –.......................... 15

4-6. Printed Wiring Boards – PANEL Section – .................. 17

4-7. Schematic Diagram – PANEL Section –....................... 19

4-8. Printed Wiring Boards – POWER Section – ................. 21

4-9. Schematic Diagram – POWER Section – ..................... 23

4-10. IC Pin Function Description ........................................... 26

5. EXPLODED VIEWS................................................ 27

6. ELECTRICAL PARTS LIST ............................... 31

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK !OR DOTTED

LINE WITH MARK !ON THE SCHEMATIC DIAGRAMS

AND IN THE PARTS LIST ARE CRITICAL TO SAFE

OPERATION. REPLACE THESE COMPONENTS WITH

SONY PARTS WHOSE PART NUMBERS APPEAR AS

SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-

LISHED BY SONY.

– 3 –

SECTION 1

GENERAL

LOCATION OF CONTROLS

Front Panel

Rear Panel

1U(Power) switch and indicator

2TAPE MONITOR switch and indicator

3INPUT SELECTOR switch and indicator

4ATTENUATOR control

5PHONES jack

6Remote control sensor

7SPEAKERS switch

8BASS control

9TREBLE control

!º BALANCE control

!¡ SOURCE DIRECT switch and indicator

!™ MUTING swith and indicator

1234

56 7 8 9 !º !¡ !™

1PHONO

2CARTRIDGE MM/MC

3SIGNAL GND y

4Mains lead

5SPEAKERS MAIN/BI-WIRE

6TAPE 1/DAT

7TAPE 2/MD

8AUX

9CD

!º TUNER

– 4 –

connector

(CN2)

connector

(CN700)

connecto

(CN103)

connector

(CN303)

connector

(

CN102

)

two screws

three screws

two screws

four screws

two screws

connector

(CN503)

sub panel section

CASE, FRONT PANEL

SUB PANEL SECTION

Note: Follow the disassembly procedure in the numerical order given.

SECTION 2

DISASSEMBLY

two screws

(CASE 3 TP2)

1

screw

(CASE 3 TP2)

two screws

(CASE 3 TP2)

case

(413235)

two screws

(CASE 3 TP2)

three screws

four screws

front panel

knob (SEL)

knob (VOL)

– 5 –

MAIN BOARD

connector

(CN752)

connector

(CN104)

connector

(CN751)

three screw

(BV/RING)

four screws

main board

four screws

three screws

– 6 –

Bias Adjustment

1. Rotate fully the bias adjusting semi-fixed resistors (RV500,

RV600) to the MIN position (counterclockwise).

2. Connect a digital voltmeter to the CN500 and CN600.

3. Set the slidack to 0 V, and press the Ubutton (ON) on the

set.

4. Raise gradually the slidack voltage up to the rated voltage

(230 V).

5. At this time, confirm that the SP relay is turned on (it will

click), and at the same time, the LED on the Ubutton changes

from red to green.

6. Adjust the RV500 and RV600 so that a reading of digital volt-

meter is 10 mV ± 2 mV.

7. Return the slidack to 0 V, and press the Ubutton (OFF) on

the set.

Adjustment Location:

1 pin 3 pin

CN500 + –

CN600 – +

SECTION 3

ELECTRICAL ADJUSTMENTS

C720

C721

Q507 Q607

RV600

RV500

CN500 CN600

113

MAIN Board (Component Side)

– 7 – – 8 –

SECTION 4

DIAGRAMS

• Circuit Boards Location 4-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

(In addition to this, the necessary note is printed in each block.)

Note on Schematic Diagram:

• All capacitors are in µF unless otherwise noted. pF: µµF

50 WV or less are not indicated except for electrolytics

and tantalums.

• All resistors are in Ωand 1/4W or less unless otherwise

specified.

•2: nonflammable resistor.

•5: fusible resistor.

•C: panel designation.

Note on PrintedWiring Boards:

•X: parts extracted from the component side.

•b: Pattern from the side which enables seeing.

• Indication of transistor.

•U: B+ Line.

•V: B– Line.

•H: adjustment for repair.

• Voltages and waveforms are dc with respect to ground

under no-signal conditions.

no mark: POWER ON

• Voltagesare taken with aVOM(Inputimpedance10 MΩ).

Voltage variations may be noted due to normal produc-

tion tolerances.

• Waveforms are taken with a oscilloscope.

Voltage variations may be noted due to normal produc-

tion tolerances.

• Circled numbers refer to waveforms.

• Signal path.

K:TUNER

NOTE:The components identified by mark !or dotted line

with mark !are critical for safety.

Replace only with part number specified.

These are omitted.

SP TM board

PS board

MAIN board

PHONO board

INPUT board

VOL board

SW board

LED board

PANEL board

HP board

POWER LED board

4-2. PRINTED WIRING BOARDS – INPUT Section – • See page 7 for circuit Boards Location.

TA-FA30ES

– 9 – – 10 –

Ref. No. Location

D101 C-6

D103 D-4

D104 D-3

D105 D-3

D106 C-3

D107 B-3

D108 A-3

D109 A-3

D110 D-4

D151 C-9

D251 C-9

• Semiconductor Location

Q100 C-5

Q101 C-5

Q102 C-5

Q103 C-6

Q104 C-6

Q105 C-6

Q152 C-9

Q252 C-9

(Page 14)

(Page 18)

(Page 17)

– 11 – – 12 –

TA-FA30ES

4-3. SCHEMATIC DIAGRAM – INPUT Section –

(Page 20)

(Page 19)

(Page 16)

4-4. PRINTED WIRING BOARDS – MAIN Section – • See page 7 for Circuit Boards Location.

TA-FA30ES

– 13 – – 14 –

Ref. No. LocationRef. No. Location

D500 D-3

D501 D-3

D502 D-3

D503 C-2

D504 C-2

D505 C-2

D506 C-4

D511 C-10

D513 B-10

D600 A-3

D601 A-3

D602 A-3

D603 B-2

D604 B-2

D605 B-2

• Semiconductor Location

D606 B-4

D700 F-11

D701 F-11

D702 F-11

D703 A-8

D704 A-8

D720 B-5

D721 C-5

IC700 F-10

Q500 D-1

Q501 D-2

Q502 D-2

Q503 D-2

Q504 D-2

Q505 D-3

Q506 C-1

Q507 C-3

Q508 D-4

Q509 D-4

Q510 C-5

Q511 E-7

Q512 E-4

Q513 D-6

Q600 A-1

Q601 A-2

Q602 A-2

Q603 B-2

Q604 B-2

Ref. No. Location Ref. No. Location

Q605 B-3

Q606 B-1

Q607 B-3

Q608 B-4

Q609 B-4

Q610 B-5

Q611 A-4

Q612 A-7

Q613 A-6

Q700 F-10

Q701 F-11

Q702 A-8

Q703 A-8

(Page 18)

(Page 17)

(Page 18)

(Page 22)

(Page 9)

Andere Handbücher für TA-FA30ES

Inhaltsverzeichnis

Andere Sony Verstärker Handbücher

Sony

Sony XM SD22X Bedienungsanleitung

Sony

Sony PHA-2 Bedienungsanleitung

Sony

Sony TA-N77ES Bedienungsanleitung

Sony

Sony XM-604M - Amplifier Bedienungsanleitung

Sony

Sony XM-GS4 Bedienungsanleitung

Sony

Sony TA-F333ESL Bedienungsanleitung

Sony

Sony XM-604M - Amplifier Bedienungsanleitung

Sony

Sony TA-S9D Bedienungsanleitung

Sony

Sony Xplod XM-5040X Bedienungsanleitung

Sony

Sony XM-5020X-UK Bedienungsanleitung

Sony

Sony STR-AN1000 Referenzhandbuch

Sony

Sony XM-752EQX Bedienungsanleitung

Sony

Sony TA-SV7AV Bedienungsanleitung

Sony

Sony XM-754HX Operating Instructions (English Bedienungsanleitung

Sony

Sony TA-DX80 Bedienungsanleitung

Sony

Sony TA-EX660 Bedienungsanleitung

Sony

Sony TA-E9000ES - Stereo Preamplifier Kurzanleitung

Sony

Sony XM-SD46X - Stereo Power Amplifier Bedienungsanleitung

Sony

Sony PHA-1A Benutzerhandbuch

Sony

Sony TA-313 Bedienungsanleitung

Sony

Sony XM-GTR2022 Bedienungsanleitung

Sony

Sony XM-1600GSD Marketing Specifications,... Bedienungsanleitung

Sony

Sony XM-N502 Bedienungsanleitung

Sony

Sony XM-504Z - Stereo Power Amplifier Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung

Phonic

Phonic XP 3000 Bedienungsanleitung