Sony CDU 5211 Series Bedienungsanleitung

CDU 5211 Series

NOTE: This manual is subject to change without notice.

CDU 5211 Series

CD-ROM Drive

User’s Manual

Revision 1

Printed in Australia

Owner’s Record

The model and serial numbers are located on the topside of the drive. Record these

numbers in the space provided below. Refer to them whenever you call upon your sales

representative regarding this product.

Model No._________________ Serial No. _______________

WARNING

To prevent re or shock hazard, do not expose the unit to rain or moisture.

To avoid electrical shock, do not open the cabinet.

Refer servicing to qualied personnel only.

CAUTION

The use of optical instruments with this product will increase eye hazard.

The use of controls or adjustments or performance of procedures other than those

specied herein may result in hazardous radiation exposure.

This unit uses CD-ROM discs with the following mark.

When you use this unit as an audio CD player, use compact discs

with the following mark.

CAUTION

LASER RADIATION WHEN OPEN.

DO NOT STARE INTO BEAM

ATTENTION

RAYONNEMENT LASER EN CAS D’OUVERTURE.

NE PAS REGARDER DANS LE FAISCEAU.

This label is located on the drive unit’s

internal chassis.

Dieses Etikett bendet sich auf dem inneren

Chassis des Laufwerkes

This label is located on the top of

the drive.

Dieser Aufkleber bendet sich an

der Oberseite des Gehäuses.

CAUTION INVISIBLE LASER RADIATION WHEN OPEN. DO NOT

STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL

INSTRUMENTS.

VORSICHT UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG

GEÖFFNET. NICHT IN DEN STRAHL BLICKEN, AUCH

NICHT MIT OPTISCHEN INSTRUMENTEN.

ADVARSEL USYNLIG LASERSTRÅLING VED ÅBNING SE IKKE IND I

STRÅLEN-HELLER IKKE MED OPTISKE INSTRUMENTER.

ADVARSEL USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES. STIRR

IKKE INN I STRÅLEN ELLER SE DIREKTE MED OPTISKE

INSTRUMENTER.

VARNING OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR

ÖPPNAD. STIRRA EJ IN I STRÅLEN OCH BETRAKTA EJ

STRALEN MED OPTISKA INSTRUMENT.

VARO! AVATTAESSA OLET ALTTIINA NÄKYMÄTTÖMÄLLE

LASERSÄTEILYLLE. ÄLÄ TUIJOTA SÄTEESEEN ÄLÄKÄ

KATSO SITÄ OPTISEN LAITTEEN LÄPI.

INFORMATION

You are cautioned that any changes or modications not expressly approved in this

manual could void your warranty covering this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

- Re-orient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

This CD-ROM Drive Unit is classied as a CLASS 1

LASER PRODUCT.

The CLASS 1 LASER PRODUCT label is located on the

top of the drive.

Safety Notice

1. Do not install or operate the product in high temperature, humidity or dusty

environment.

2. Do not attempt to open the cover to repair the product yourself.

3. Never spill liquid of any kind on the product.

4. Always follow instructions on this manual under operating the product.

5. To prevent exposure to laser emanations (harmful to human eyes), do not

attempt to disassemble this unit.

6. Hold CD discs by their edges. Do not touch the surface of the discs.

7. The drive is designed to be incorporated into a computer-based system or

unit which has an enclosing cover. Using the drive alone or in any other

conguration is prohibited.

Caution:

Use of controls or adjustments or performance of procedures other than those

specied herein may result in hazardous radiation exposure.

ACKNOWLEDGMENTS & TRADEMARKS

All contents are subject to change at any time without notice. No responsibility is

assumed for its use; nor for infringements of patents or other rights of third parties and

no patent or license is implied hereby.

All trademarks are the property of their respective owners.

CLASS 1

LASER PRODUCT

LASER KLASSE 1

PRODUKT

Warnings and Precautions 7

Introduction 8

Features............................................................................................................8

Software Requirements....................................................................................9

Using the Drive 10

Front Panel.....................................................................................................10

“Maximum Speed Choice” function..............................................................11

Installing the Drive 12

System Requirements.....................................................................................12

Hardware Installation.....................................................................................12

Connections & Settings .................................................................................13

Connecting the IDE cable ..............................................................................14

Trouble Shooting 15

Specications 16

General...........................................................................................................16

Performance ...................................................................................................16

Audio..............................................................................................................16

Reliability.......................................................................................................16

Power Requirements ......................................................................................16

Environmental Conditions .............................................................................17

Dimensions & Mass.......................................................................................17

CONTENTS

WARNING - Possible voiding of Warranty

Please be aware that cracked, deeply scratched or other poor quality discs used in

this drive may cause damage to the drive and / or the data on the disc. Such discs

may break at high speed rotation. If full care is not exercised in relation to this

matter you may void the warranty of this product.

PRECAUTIONS

· Do not attempt to open the drive and service it. Removing the cover may

cause exposure to harmful laser beams and electrical voltages. User is recom-

mended to get service by returning the defected drive back to the original

vendor where the drive is purchased.

· Use the original packing for transporting the drive or sending back for

service. The original packing were designed and tested to protect your drive

under rough conditions.

· Do not put this CD-ROM drive in direct sunlight, on heat units, or near

electrical appliances which draw large amounts of current.

· Keep your discs clean. Using soft, dust-free cloth to clear the surface of the

disc.

· Do not drop or jolt the drive.

· Keep the area around the CD-ROM drive clean from dust, smoke, and other

contaminants.

WARNINGS & PRECAUTIONS

Features

The CDU 5211 is an internal CD-Rom (Compact Disc - Read Only

Memory) drive unit designed for use with personal computers. It comes

with the following features:

General

• Speed: 52X max / 40X default.

• “Maximum Speed Choice” function.

• 40 Pin ATAPI - IDE interface.

• 5 1/4 inch half-height drive form factor.

• Power loading and eject of a disc.

• ABS (Auto Balance Spindle) to reduce noise and vibration.

• 128 KB of buffer memory.

• Power saving functions.

• Vertical mount ability.

• Small CPU bandwidth consumption.

• Software volume control.

• Easy audio CD-DA control button.

Supported Disc Formats

The CD 5211 is a “Multiread” compliant drive and can read data in each

of the following formats:

CD-DA, CD-ROM Mode-1, CD-ROM/XA Mode-2 Form-1 &

Form-2, CDI-Ready, Photo-CD, Karaoke-CD, Video CD (MPEG-1),

Enhanced CD, CD Extra, I-Trax CD, CD-Text, UDF.

Media Types

CD-ROM, CD-R and CD-RW.

12cm & 8cm discs.

Audio

• Outputs 16-bit digital data over the ATA interface.

• Audio line output (rear panel) and headphones jack (front panel) for

audio CD playback.

INTRODUCTION

Software Requirements

Reading Data

For your computer to recognise your new CD-Rom drive and to be able to

access data from it, the correct device drivers must be installed.

Most modern operating systems such as Microsoft® Windows 95™,

Windows 98™, Windows ME™, Windows NT4™ and Windows

2000™ along with most versions of Linux and OS/2™ include these

drivers as standard in the operating system, hence no additional drivers are

required for reading discs on these operating systems.

Windows 3.xx™ and MS-DOS™

If you require the drive to be recognised by Microsoft Windows 3.xx or

MS-DOS you will need to install the MS-DOS™ device driver. It can be

downloaded from our support web site:

http://www.sony.com.au/support/itp

NOTE: If using Windows 95 or later and you have previously

installed the MS-DOS device driver it is recommended that you disable

or remove MS-DOS device driver as it will decrease performance.

INTRODUCTION

124

3567

1 - Earphone Jack Stereo mini-jack for headphones and/or powered speakers.

2 - Volume Control Control volume of earphone jack. This control has no effect

on rear panel audio output.

3 - Emergency Eject In case the Eject button isn’t working, insert a small

paper clip into this hole to eject the tray.

Note: Turn off the power before doing this manual ejection.

4 - On/Busy LED The On/Busy LED will be ashing while the CD-ROM

drive is busy.

5 - Disc Tray The user can open or close the disc tray by pressing the

Open/Close button.

6 - Play/Skip Will start playing of an Audio-CD or Skip to next track if

already playing an Audio-CD.

7 - Stop/Eject/Speed Will eject the tray if a CD-ROM is playing.

Will stop an Audio-CD playing, pressing it again will eject

the tray as usual.

Pressing this button can also change the max drive speed.

The default max speed is 40X. Press and hold for 5 seconds

to change the drive speed from 40X to 52X.

Tray out disc will reset drive speed from 52X to 40X

automatically.

Front Panel “Maximum Speed Choice” function

The CDU-5211 has a Maximum Speed Choice function where the user can select between

maximum speeds of 40X or 52X.

The drive always defaults to 40X.

To activate 52X operation press and hold the Stop/Eject button for 5 seconds.

The drive will then read the current disc at 52X speed.

When the disc is ejected the drive will default back to 40X operation.

It is recommended that 52X operation only be activated under the following conditions

- You are condent that the disc been used is in good condition and

free from marks and scratches.

- The disc is well balanced and does not have thick printed ink or

adhesive labels attached to its surface.

- The disc is not physically damaged in any maner.

Discs that have the above characteristics may reduce maximum transfer speeds due to

excessive disc vibration at 52X.

NOTE: Physically damaged discs may void warranty - refer to “Warnings &

Precautions” on page 7 of this manual.

USING THE DRIVEUSING THE DRIVE

INSTALLING THE DRIVE

System Requirements

To ensure stable performance, the following system specications are recommended.

OS DOS 6.xx or higher, Windows 3.1x, 95/98/ME/2000/

NT 4.0, OS/2 Warp 3.0 or higher.

Interface Vacant IDE interface connector

NOTE: To operate the drive using DOS 6.xx or higher you will need to

install the DOS device drivers. These are available for free download

from our support web site:

http://www.sony.com.au/support/itp

Hardware Installation

Please refer to your PC’s user manual and follow their guidelines for adding

hardware components. Always follow their anti-static precautions.

1 Set the Master/Slave jumper on CD-ROM rear panel (refer to gure 1)

2 Locate an empty drive bay and slide the CD-ROM drive into the bay. Secure

with four screws.

3 Connect the power supply cable to the CD-ROM drive. (Ensure the pin

denition of power connector is the same as shown in gure 1).

4 Connect the 40 pin IDE / ATAPI cable to the CD-ROM drive according to the

description in gure 1 (Note: Pin 1 on the cable is generally indicated by a

red stripe along the edge of the ribbon cable).

5 Connect the sound cable from the Analog Audio on the rear panel of

CD-ROM to your sound card (if you have a sound card in your system).

6 Follow you PC’s user manual to re-assemble your PC.

NOTE: For optimum performance on Windows based systems the drives DMA

setting in the device manager should be enabled. Refer to your Systems help

menu for assistance.

Connections and Settings

There are three pairs of jumpers, MA (Master), SL (Slave) and CS (Cable Select) on

the rear panel of your CD-ROM drive. Figure 1 shows the location of each jumper.

CS (CSEL)

If your system supports the CS setting you can set the jumper to the “CS” position. The

Master/Slave setting will then be made automatically depending on your hardware

Conguration. No jumper is then required on the “MA” or “SL” pins.

INSTALLING THE DRIVE

C S M

S L A

C S M

S L A

Master Device

(Factory default setting)

Slave Device

Rear of Drive

Figure 1

DC RCCL

C S M

S L A

Cable Select

Slave

Master HOST INTERFACE POWER

2+5 G G +12

Digital

Audio

Analogue

Audio

INSTALLING THE DRIVE

Connecting the IDE cable

Most PC systems can connect up to 4 devices on the IDE ports. Your PC should consist

of a “Primary IDE Bus” and a “Secondary IDE Bus” each of which can have two

devices connected to it - a “Master device” and a “Slave device” Refer Figure 2

In most PC systems, the hard disk drive is set as the “Master Device” on the “Primary

IDE Bus”, this should not be altered.

If available it is recommended that you connect the CD-ROM drive as the “Master

Device” on the “Secondary IDE Bus”.

The CD-ROM drive can also be set as the “Slave Device” on either bus if both of the

“Master Device” possibilities have been taken by other devices. Some devices such as

CD writers and DVD drives may be required to be set as the “Master Device”, in this

case it is OK to set the CD-ROM drive as the “Slave Device”.

Secondary IDE Bus

Primary IDE Bus PC Mother Board

Device 2

(Slave)

Device2

(Slave)

Hard Disk

(Master)

Device 1

(Master)

Figure 2

TROUBLE-SHOOTING

If you experience any trouble during installation or normal use of your CD-ROM

drive, please refer to the following information.

You will nd further information on our support web site:

http://www.sony.com.au/support/itp

Symptoms Action

Appears to have no power. Check DC power cable connection.

CD drive not recognised by system. Check IDE interface connections.

Check the MASTER/SLAVE settings of

all devices.

The disc tray will not open . Disable the “lock eject” feature software

of the operating system.

Shut power down and use emergency

eject hole to eject disc.

Cannot read data on discs. Check the surface of CD media, always

keep it clean and free from scratches.

Check the quality of CD media.

Check if other discs or music CD’s

are reading OK.

Is Disc inserted upside down?

Could disc be a UDF formatted

disc? Check if a UDF reader is installed.

No sound. Check sound cable connections.

Check the volume settings of the drive

and operating system volume controls.

Are speakers turned on?

SONY CDU5211 Product Specifications Version 1.1 16

5. MECHANICAL DRAWINGS

SPECIFICATIONS

General

Host Interface ATA-PI compliant.

Acceptable Formats CD-DA, CD-Rom mode 1, CD-Rom/XA

mode 2 form 1 & form 2, CD-I Ready,

Video CD (MPEG-1), Karaoke CD,

Photo CD, Enhanced CD, CD extra,

I-Trax CD, CD-Text and UDF.

Acceptable Media Types CD-Rom, CD-R, CD-RW,

Acceptable Disc Diameters 12 cm and 8 cm.

Performance

Rotational Speeds CD-Rom, Max - 52X, 7800 KB/sec.

CD-Rom, Max - 40X, 6,000 KB/sec.

Random access time 80 ms.

Data Buffer 128 KB.

Burst Data Rate Ultra DMA- 33.3 MB/sec.

DMA mode 2- 16.6 MB/sec.

PIO mode 4- 16.6 MB/sec.

Audio

Earphone Output (Front) 0.7 +/- 0.2 VRMS @ 33Kohms,

1KHz, 0db

Line Output (Rear) 0.7 +/- 0.2 VRMS @ 47Kohms,

1KHz, 0db

Digital Output 5.0 Vp-p - SPDIF Standard

Reliability

Error Rate Mode-1 (ECC on) 10 -12 Block/Bit

Mode-2 (ECC off) 10 -9 Block/Bit

MTBF 70,000 POH @ 25% duty cycle

Power Requirements

Operation Max +5V = 1.0 amps

+12V = 1.5 amps

Sleep Average +5V = 0.03 amps

+12V = 0.01 amps

Voltage Requirements +5V +/- 5% and less than 100m Vp-p

ripple voltage

+12V +/- 10% and less than 200m

Vp-p ripple voltage

SPECIFICATIONS

Environmental Conditions

Operating Temp 5°C to 45°C

Humidity 10% to 80% RH

Altitude 0 ~ 3,500 m

Non Operating Temp -35°C to 60°C

Humidity 10% to 90% RH

Altitude 0 ~ 12,500 m

Dimensions & Mass

Dimensions 145.8 x 41.3 x 190 mm

(WxHxD +/- 0.5mm)

Weight 0.9Kg

Inhaltsverzeichnis

Andere Sony CD/CDR-Laufwerk Handbücher

Sony

Sony CRX - 160E Bedienungsanleitung

Sony

Sony VPCEF Series Leitfaden

Sony

Sony CRX230AE Bedienungsanleitung

Sony

Sony XDCAM PDW-U1 Bedienungsanleitung

Sony

Sony CRX220A1 Bedienungsanleitung

Sony

Sony CRX175A1 Bedienungsanleitung

Sony

Sony CRX230AD Bedienungsanleitung

Sony

Sony DRX-S70U-W Bedienungsanleitung

Sony

Sony CDU924S Bedienungsanleitung

Sony

Sony CRX230A Bedienungsanleitung

Sony

Sony XDCAM PDW-U1 Bedienungsanleitung

Sony

Sony CDU926S Bedienungsanleitung

Sony

Sony PCG-GRT Series Leitfaden

Sony

Sony MO DISK DRIVE SMO-F551 Bedienungsanleitung

Sony

Sony varo PCGA-CD51 Bedienungsanleitung

Sony

Sony VPCB1 Series Leitfaden

Sony

Sony BDX-S500U Bedienungsanleitung

Sony

Sony CDU535 Series Bedienungsanleitung

Sony

Sony VPCS1 Series Leitfaden

Sony

Sony SMO-F561 Bedienungsanleitung

Sony

Sony CRX1650L Bedienungsanleitung

Sony

Sony XDCAM PDW-U1 Bedienungsanleitung

Sony

Sony VGN-N1 Series Leitfaden

Sony

Sony SDX-D700C Handbuch

Beliebte CD/CDR-Laufwerk Handbücher anderer Marken

Philips

Philips CDD3610 Bedienungsanleitung

QPS

QPS Que!Fire Bedienungsanleitung

LG GCC-4241N Bedienungsanleitung

Plextor

Plextor 12X-3 Leitfaden

Samsung

Samsung SN-324B Bedienungsanleitung

Teac

Teac CD-211E Bedienungsanleitung

SmartDisk

SmartDisk Firewire CD-R/W Bedienungsanleitung

Axis

Axis CD-ROM SERVER Bedienungsanleitung

LG CRD-8322B Bedienungsanleitung

Memorex

Memorex 32023234 - 52x32x52x External USB2.0 CD... Montageanleitung

Yamaha

Yamaha CD Recordable/Rewritable Drive CRW3200 Bedienungsanleitung

Panasonic

Panasonic KX-LD742 Bedienungsanleitung

Pioneer

Pioneer BDR-S13U-X Bedienungsanleitung

Panasonic

Panasonic LK-MC606BP Bedienungsanleitung

Panasonic

Panasonic CF-VCW Series Bedienungsanleitung

LG CRD-8320B Bedienungsanleitung

Conner

Conner CFP2107 Series Bedienungsanleitung

Plextor

Plextor 12-20C Leitfaden