Sony BVE-700A Bedienungsanleitung

EDITING CONTROL UNIT

BVE-700A

INSTALLATION MANUAL

1st Edition (Revised 1)

Serial No. 10001 and Higher

BVE-700A

!WARNING

This manual is intended for qualified service personnel only.

To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that

contained in the operating instructions unless you are qualified to do so. Refer all servicing to

qualified service personnel.

!WARNUNG

Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.

Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die

Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei

Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben

Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung

dazu besitzen.

!AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin

de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les

réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.

Pour toute réparation faire appel à une personne compétente uniquement.

Attention-when the product is installed in Rack:

1. Prevention against overloading of branch circuit

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

make sure that the rack does not overload the supply

circuit.

2. Providing protective earth

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

confirm that the outlet is provided with a suitable

protective earth connection.

3. Internal air ambient temperature of the rack

When this product is installed in a rack, please make

sure that the internal air ambient temperature of the

rack is within the specified limit of this product.

4. Prevention against achieving hazardous

condition due to uneven mechanical loading

When this product is installed in a rack, please make

sure that the rack does not achieve hazardous

condition due to uneven mechanical loading.

5. Install the equipment while taking the operating

temperature of the equipment into consideration

For the operating temperature of the equipment, refer

to the specifications of the Operation Manual.

6. When performing the installation, keep the

following space away from walls in order to

obtain proper exhaust and radiation of heat.

Front, Left : 10 cm (4 inches) or more

1 (E)

BVE-700A

Table of Contents

Manual Structure

Purpose of this manual ........................................................... 2 (E)

Related manuals ..................................................................... 2 (E)

Contents .................................................................................. 2 (E)

Trademarks ............................................................................. 2 (E)

1. Installation

1-1. Operating Environment ........................................... 1-1 (E)

1-2. Power Supply ........................................................... 1-1 (E)

1-3. Installation Space ..................................................... 1-2 (E)

1-4. Matching Connectors and Cables ............................ 1-4 (E)

1-5. Input/Output Signals of Connectors ........................ 1-5 (E)

1-6. Function of Switch and LED on Board ................... 1-7 (E)

1-7. Rack Mounting ........................................................ 1-9 (E)

1-8. Installing the BKE-701A ....................................... 1-10 (E)

2. Service Overview

2-1. Removing/Reinstalling Front Panel ......................... 2-1 (E)

2-2. Cleaning ................................................................... 2-1 (E)

2-2-1. Filter ............................................................... 2-1 (E)

2-2-2. Fan .................................................................. 2-1 (E)

2-3. Data Backup Capacitor ............................................ 2-2 (E)

2 (E) BVE-700A

Purpose of this manual

This manual is the installation manual of Editing Control Unit BVE-700A.

This manual is intended for use by trained system and service engineers, and

describes the information on installing the BVE-700A.

Related manuals

Beside this Installation Manual, the following manuals are available for the unit.

.User’s Guide (Supplied with BVE-700A)

This manual describes the application and operation of the unit.

.Operation Manual (Supplied with BVE-700A)

This manual describes the overview, system connection examples, and specifica-

tions of the unit.

.BKE-701A Installation Manual (Supplied with BKE-701A)

This manual describes the information related to the installation of the unit.

.BVE-700A/BKE-701A Maintenance Manual (Available on request)

This manual describes the information that premise the service of BVE-700A/

BKE-701A based on components replaced.

.“Semiconductor Pin Assignments” CD-ROM (Available on request)

This “Semiconductor Pin Assignments” CD-ROM allows you to search for

semiconductors used in B&P Company equipment.

The maintenance manual contains a complete list of semiconductors and their ID

Nos., and thus should be used together with the CD-ROM.

Part number: 9-968-546-XX

Contents

This manual is organized by following sections.

Section 1 Installation

This section describes the operating environment, power supply, installation space,

installation of optional board, rack mounting, connectors, input and output signals of

connectors, switch settings on board and LED description.

Section 2 Service Overview

This section describes the cleaning and the capacitor for backing up the data.

Trademarks

Trademarks and registered trademarks used in this manual are follows.

.Ethernet is a registered trademark of Xerox Corporation.

Manual Structure

1-1 (E)

BVE-700A

1-1. Operating Environment

Operating guaranteed temperature : +5 dC to +40 dC

Performnace guaranteed temperature : +10 dC to +35 dC

Operating humidity : 10 % to 90 %

(relative humidity)

Storage temperature : _20 dC to +60 dC

Mass : Processor unit 12 kg

(with BKE-701A

installed)

Control panel 4.5 kg

Prohibited locations

.Areas where the unit will be exposed to direct sunlight or

any other strong lights.

.Dusty areas

.Areas where it is subject to vibration.

.Areas with strong electric or magnetic fields.

.Areas near heat sources.

.Areas where is subjected to electricity noise.

.Areas where is subjected to static electricity noise.

Ventilation

The inside of the BVE-700A is air-cooled by a fan (on left

side).

The power supply can be damaged if the exhaust vent (left

side panel) and air intake (front panel) are blocked or the

fan is stopped.

Therefore, leave a blank space of more than 10 cm in the

front and left side of the BVE-700A.

1-2. Power Supply

1. Power specifications

A switching regulator is used for the power supply of this

unit. The voltage within the range of 100 V to 240 V can

be used without changing the supply voltage.

Power requirements : AC 100 to 240 V ±10 %

50/60 Hz

Current consumption : Maximum AC100 V ; 1 A

Maximum AC240 V ; 0.5 A

(with all optional boards installed)

As the inrush current at turn-on is the maximum 35 A (at

100 V/85 A (at 240 V), the capacity of the AC power must

be commensurate in it.

If the capacity of the AC power is not the adequately large,

the breaker of the AC power at the supply side will operate

or the unit will abnormally operate.

Section 1

Installation

2. Recommended Power Cord

The power cord is not supplied with the BVE-700A.

To get a power cord, please contact your local Sony Sales

Office/Service Center.

.Use the approved Power Cord (3-core mains lead)/

Appliance Connector/Plug with earthing-contacts that

conforms to the safety regulations of each country if

applicable.

.Use the Power Cord (3-core mains lead)/Appliance

Connector/Plug conforming to the proper ratings (Volt-

age, Ampere).

If you have questions on the use of the above Power Cord/

Appliance Connector/Plug, please contact your local Sony

Sales Office/Service Center.

.Never use an injured power cord.

.Plugging the power cord in the AC inlet, push as far as it

will go.

For customers in the U.S.A. and Canada

1Power cord, 125 V 10 A (2.4 m) : !1-557-377-11

AC inlet

For customers in the all European countries

1Power cord, 250 V 10 A (2.4 m) : !1-782-929-22

AC inlet

1-2 (E) BVE-700A

1-3. Installation Space

Processor unit

520

440

465

57.2

375

482

61 380

17.5

132.4

Unit : mm

1-3 (E)

BVE-700A

Control panel unit

Unit : mm

340

315.5

281

277.2

315

16.9

1-4 (E) BVE-700A

1-4. Matching Connectors and Cables

Use the following connectors, cables, or equivalents when connecting cables to the unit.

Panel indication Connector name Matching connector and cable

Name Sony part No.

Processor unit

PLAYER-1 D-sub 9-pin, Female D-sub 9-pin, Male

PLAYER-2 Connector 9-pin, Male 1-560-651-00*1

PLAYER-3 Junction Shell 9-pin 1-561-749-00

RECORDER

MIXER

SWER

Processor unit

EDL D-sub 9-pin, Male D-sub 9-pin, Female

Connector 9-pin, Female 1-563-815-21

Junction Shell 9-pin 1-561-749-00

Processor unit

GPI D-sub 15-pin, Female D-sub 15-pin, Male

Connector 15-pin, Male 1-564-600-11*1

Junction Shell 15-pin 1-563-376-11

Processor unit

SDI IN BNC, 75 ZBNC, 75 Z

SDI OUT 5C-FB coaxial cable

Processor unit

REF VIDEO BNC, 75 ZBNC, 75 Z

Belden 8281 coaxial cable

Processor unit/Control panel unit

PANEL D-sub 15-pin, Female D-sub 15-pin, Male

Connector 15-pin, Male 1-564-600-11*1

Junction Shell 15-pin 1-563-376-11

Processor unit

NETWORK RJ-45 modular jack*2__

*1 : To use plugs, the following crimp contacts are required.

AWG #18 to #22 : 1-566-493-21

AWG #22 to #24 : 1-564-774-11

AWG #24 to #30 : 1-564-775-11

*2 : Conforms to the IEEE 802.3 Ethernet 10BASE-T/100BASE-TX standards.

1-5 (E)

BVE-700A

1-5. Input/Output Signals of Connectors

The input/output signals of the connectors at the rear panel

are as follows.

.Processor unit

PLAYER-1

PLAYER-2

PLAYER-3

RECORDER

MIXER

SWER : RS-422A (D-sub 9-pin, Female)

Pin No. Signal Function

1 GND Ground

2RX_Received data (_)

3TX+Transmitted data (+)

4 GND Ground

5_No Connection

6 GND Ground

7 RX+ Received data (+)

8TX_Transmitted data (_)

9_No Connection

EDL : RS-232C (D-sub 9-pin, Male)

Pin No. Signal Function

1_No Connection

2 RXD Received data

3 TXD Transmitted data

4_No Connection

5 GND Ground

6_No Connection

7 RTS (Not used at present)

8 CTS (Not used at present)

9_No Connection

_ EXT VIEW _

GPI : D-sub 15-pin, Female

Pin No. Signal Function

1 GND Ground

2 OUT-1A Relay output-1A

3 OUT-2A Relay output-2A

4 OUT-3 (TTL) Open collector output-3

5 OUT-4 (TTL) Open collector output-4

6 IN-1 (TTL) Input-1

7 IN-3 (TTL) Input-3

8 GND Ground

9 OUT-1B Relay output-1B

10 OUT-2B Relay output-2B

11 _No Connection

12 _No Connection

13 GND Ground

14 IN-2 (TTL) Input-2

15 IN-4 (TTL) Input-4

_ EXT VIEW _

1-6 (E) BVE-700A

PANEL : D-sub 15-pin, Female

Pin No. Signal Function

1 GND Ground

2RX_Received data (_)

3TX+Transmitted data (+)

4 GND Ground

5_No Connection

6 12 V Panel Power Supply

7 12 V Panel Power Supply

8 12 V Panel Power Supply

9_No Connection

10 RX+Received data (+)

11 TX_Transmitted data (_)

12 GND Ground

13 GND Ground

14 GND Ground

15 GND Ground

NETWORK : 10BASE-T/100BASE-TX (8-pin, Modular jack)

Pin No. Signal Function

1TX+Transmitted data (+)

2TX_Transmitted data (_)

3RX+Received data (+)

4_No Connection

5_No Connection

6RX_Received data (_)

7_No Connection

8_No Connection

.Control panel unit

EDITOR : D-sub 15-pin, Female

Pin No. Signal Function

1 GND Ground

2RX_Received data (_)

3TX+Transmitted data (+)

4 GND Ground

5_No Connection

6 12 V Panel Power Supply

7 12 V Panel Power Supply

8 12 V Panel Power Supply

9_No Connection

10 RX+Received data (+)

11 TX_Transmitted data (_)

12 GND Ground

13 GND Ground

14 GND Ground

15 GND Ground

_ EXT VIEW _

Andere Handbücher für BVE-700A

Inhaltsverzeichnis

Andere Sony Steuereinheit Handbücher

Sony

Sony BKM-35H Bedienungsanleitung

Sony

Sony HDCU-1700 Bedienungsanleitung

Sony

Sony DTP-T1000 A Bedienungsanleitung

Sony

Sony KCC-PCH Bedienungsanleitung

Sony

Sony SVRM-911 Bedienungsanleitung

Sony

Sony BKDM-7041 Bedienungsanleitung

Sony

Sony FCB-EV7100 Bedienungsanleitung

Sony

Sony HDCU3100 Bedienungsanleitung

Sony

Sony HDCU2080 Bedienungsanleitung

Sony

Sony CCU-M5A Bedienungsanleitung

Sony

Sony DSBK-180 Bedienungsanleitung

Sony

Sony CCP-8000 Series Bedienungsanleitung

Sony

Sony HXCU-100 Bedienungsanleitung

Sony

Sony RM-450 Bedienungsanleitung

Sony

Sony CCU-550A Bedienungsanleitung

Sony

Sony CCU-700A Bedienungsanleitung

Sony

Sony HDCU2500 Bedienungsanleitung

Sony

Sony HKC-7081 Handbuch

Sony

Sony BKM-104 Bedienungsanleitung

Sony

Sony PDBK-L1500 Bedienungsanleitung

Sony

Sony HXCU-FB80 4K/HD Bedienungsanleitung

Sony

Sony Clie Gear PEGA-MSB1 Bedienungsanleitung

Sony

Sony CCU-TX7 Bedienungsanleitung

Sony

Sony CCP-9000-C Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung

Flyron

Flyron FN-BC04 Bedienungsanleitung