Sony SU-P42T1 Bedienungsanleitung

4-092-986-12 (2)

Tabletop Stand

Instructions

Mode d’emploi

Instrucciones

SU-P42T1/SU-P50T1

For Customers and Sony Dealers

in North and Central America

2(US)

Thank you for purchasing this product.

WARNING

If the safety precautions are not observed and the product is used incorrectly, it may result in a fire or serious

injury.

This instruction manual shows the important precautions necessary to prevent accidents and to promote the correct

handling of the product. Be sure to read this manual thoroughly and use the product correctly. Be sure to keep this

manual available for future reference.

This Tabletop Stand is designed for use with the Sony Flat Panel Color Television. Do not use this stand with

equipment other than the following product.

Specified product

Tabletop Stand SU-P42T1 SU-P50T1

Flat Panel Color Television KE-42XBR900 KE-50XBR900

On Safety

Products by Sony are designed with safety in mind. If the product is used incorrectly, however, it may result in a

serious injury through a fire, an electric shock or by causing the product to topple over. Be sure to observe the

precautions for safety to prevent accidents.

For Customers

WARNING

If the following precautions are not observed, there is a possibility of either death or serious injury

through a fire, an electric shock or by causing the product to topple over or fall.

Do not allow the Power Cord or the Display Interface Cable to be pinched.

•Do not allow the Power Cord or the Display Interface Cable to be pinched when

you install the Display Unit on the Tabletop Stand. If the Power Cord or the

Display Interface Cable is damaged, this may result in a fire or an electric shock.

• Do not step on the Power Cord or the Display Interface Cable when you carry

the Tabletop Stand. The Power Cord or the Display Interface Cable may be

damaged, and this may result in a fire or an electric shock.

Be sure to use the securing screws.

If the securing screws are not used, the Display Unit may fall and cause injury when the Tabletop Stand is being

carried.

Be sure to install the Tabletop Stand on a flat place.

If the Tabletop Stand is installed at an angle, it may topple over and cause injury or

property damage.

3(US)

English

Be sure to install the Tabletop Stand on a stable surface.

If you install the Tabletop Stand on an unstable surface, it may lose its balance and

topple over or fall off. This may cause injury or property damage.

Be sure to take measures to prevent the stand from toppling over.

If you fail to do so, the Tabletop Stand may topple over during an earthquake and cause injury or property

damage. Draw a wire or the like through the holes of the Security Attachments located on the upper part of the

Main Bracket and fix the other ends of the wires to the wall to anchor the Tabletop Stand and prevent it from

toppling over.

Do not lean on or hang from the Tabletop Stand.

The Tabletop Stand may topple over and cause injury.

Do not block the ventilating holes on the Display Unit.

If you block the ventilating holes on the Display Unit by covering the top of the

Tabletop Stand with a cloth or the like, the Display Unit may become overheated

and this may cause a fire.

Be sure to carry the stand in the manner shown in this manual.

If the Tabletop Stand is carried incorrectly, it may topple over and cause injury.

Do not stumble over the Power Cord or the Display Interface Cable.

If you stumble over the Power Cord or the Display Interface Cable, the Tabletop Stand may topple over and cause

injury.

Do not carry the Tabletop Stand with Display Unit installed on it.

Be sure to remove the Display Unit before attempting to carry the Tabletop Stand.

If you fail to do so, the Display Unit may fall and cause bodily injury.

CAUTION

If the following precautions are not observed, there is a possibility that the user will suffer injury or that

property damage will occur.

Do not install equipment other than the specified product.

This Tabletop Stand is designed for use with the specified product. If you install equipment other than the specified

product, it may fall and cause injury or property damage.

4(US)

Precautions

To keep the stand clean, occasionally wipe the stand with a dry soft cloth. Stubborn stains may be removed with a

cloth slightly dampened with watered-down dishwashing detergent. Then wipe the area with a dry soft cloth. Do

not use any type of chemicals, such as thinner or benzene, as they may damage the finish of the stand.

Assemble the Tabletop Stand

To Sony Dealers

The following instructions are for Sony Dealers only. Be sure to read safety precautions described above and

pay adequate attention to safety during the installation, maintenance and checking of this product.

Be sure that two or more persons do the installation work.

Be sure that two or more persons do the installation work when installing the Display Unit on the Tabletop Stand.

If one person does the installation work alone, this may result in an accident or an injury.

Be sure to assemble the Tabletop Stand securely following the instructions in

this manual.

If any of the screws are loose or fall out, the Tabletop Stand may lean and topple

over, or the Display Unit may fall. This may cause injury or property damage.

Be sure to install the Display Unit securely, following the proper procedure.

Be sure to tighten the screws firmly.

If the Display Unit is not installed securely, it may fall and cause injury.

Be careful not to hurt your hands or fingers when assembling the Tabletop

Stand.

Be careful not to hurt your hands or fingers when assembling the Tabletop Stand or when installing the Display

Unit.

Precautions on the installation

• Be sure to spread packing materials or the like over the floor beforehand when assembling the Tabletop Stand.

•Install the stand on a solid and flat floor. Do not allow the stand to be installed at an angle or leaning in one

direction. To avoid this, observe the following precautions.

– If you install the stand on a soft surface such as a mat or a carpet, lay a board on the designated location

beforehand.

– Do not install the stand in a place subject to direct sunlight or near a heater.

–Do not install the stand in a hot or humid place, or outdoors.

For Sony Dealers

5(US)

Step 1: Check the parts

•Prepare a Phillips screwdriver beforehand.

• Exercise extreme care to avoid injury when installing the Main Bracket.

Main Bracket (1 piece) Stand (1 piece)

Step 2: Install the Main Bracket

1Align the Main Bracket over the screw holes on the stand. Then fasten

the Main Bracket to the stand using 10 countersink screws.

Be sure that two or more persons hold the parts during this procedure.

Tighten the 10 countersink screws once again after screwing them temporarily.

Caution

•Be sure to hold the stand firmly and keep it stable.

•When you use an electric driver to tighten screws,

tightening torque must be approx. 1.81 Ft·lbs

(2.45N·m). Do not use impact drivers.

If you use impact drivers or electric drivers

with the tightening torque other than 1.81

Ft·lbs (2.45N·m), you will overtighten the

screws. This may destroy parts or screws, cause

the Main Bracket to drop off from the stand,

leading to any injury.

For Sony Dealers

Name Quantity

Securing screw 2

Countersink screw 10

Cable clamper 1

For Sony Dealers

Countersink

screws

Main Bracket

Stand

6(US)

Step 3: Install the Display Unit

WARNING

Be sure to complete the installation before connecting the Power Cord to the wall outlet. If you allow the Power

Cord to be pinched under or between pieces of equipment, this may result in a short circuit or an electric shock.

If you stumble over the Power Cord or the Display Interface Cable, the stand may topple over, and this may

result in injury.

1Install the Display Unit on the Tabletop Stand.

1Connect the Power Cord and the Display Interface cable to the Display Unit.

Tip

See the instruction manual of the Sony Flat

Panel Color Television (KE-42XBR900/KE-

50XBR900) for more details on connecting the

Power Cord and the Display Interface Cable.

2Be sure that two or more persons hold the right and left edges of the top and the under sides of the

Display Unit while fitting the hooks on the rear of the Display Unit into the holes on the fixtures of the

stand. Then confirm that the hooks on the rear of the Display Unit are completely inserted into the four

holes of the fixtures.

Note

Do not stumble over the Power Cord or the

Display Interface Cable.

For Sony Dealers

Rear side of the Display Unit

Soft rag such as a blanket

Power Cord

Display Interface

Cable

Rear side of the

Display Unit

7(US)

3Slide the Display Unit straight downward until it snaps on.

Notes

•Slide the Display Unit completely down

to the bottom. Confirm that the Display

Unit is installed on the stand

horizontally.

•Be sure to keep the Tabletop Stand stable

while installing the Display Unit.

2Attach the Display Unit to the stand with the two securing screws.

Hook

Securing screws

Side View

8(US)

3Route the Power Cord and the Display Interface Cable through the stand.

1Attach the cable clamper to the Main Bracket.

2Draw the Power Cord and the Display Interface Cable through the cable clamper and fix them.

3Remove the Cable Cover from the stand and route the Power Cord and the Display Interface Cable inside

the stand.

Cable clamper

Cable Cover

9(US)

4Reattach the Cable Cover to the stand.

4Take measures to prevent the stand from toppling over.

Draw a wire or the like through the holes of the security attachments located on the upper part of the Main

Bracket and fix the other ends of the wires to the wall to anchor the Tabletop Stand and prevent it from

toppling over.

WARNING

Be sure to take measures to prevent the stand

from toppling over. If you fail to do so, the

Tabletop Stand may topple over during an

earthquake and cause injury or property

damage. Draw a wire or the like through the

holes of the security attachments located on the

upper part of the Main Bracket and fix the other

ends of the wires to the wall to anchor the

Tabletop Stand and prevent it from toppling

over.

Cable Cover

Security Attachments

10(US)

Specifications

Design and specifications are subject to change without notice.

SU-P42T1 SU-P50T1

Unit: (mm/inches) A 500 (19 11⁄16)600 (23 5⁄8)

B295 (11 5⁄8)321 (12 5⁄8)

C392 (15 7⁄16)

D340 (13 3⁄8)

E310 (12 7⁄32)

F461 (18 5⁄32)

G141 (5 9⁄16)

H602 (23 11⁄16)

Weight: (kg/lb)

16.0 (35 lb 4 oz) 19.0 (41 lb 14 oz)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Sony Rack & Stand Handbücher

Sony

Sony SU-27FS2 Bedienungsanleitung

Sony

Sony SU-W110 Bedienungsanleitung

Sony

Sony SU-52NX1 Bedienungsanleitung

Sony

Sony SU-SX10 Bedienungsanleitung

Sony

Sony SU-557 Bedienungsanleitung

Sony

Sony PVMK-RX24 Bedienungsanleitung

Sony

Sony VCT-HM1 Bedienungsanleitung

Sony

Sony KDL-32EX301 - 32" Class Bravia Ex301 Hdtv Betriebsanleitung

Sony

Sony RHT-G550 Bedienungsanleitung

Sony

Sony UNI-MDB3 Bedienungsanleitung

Sony

Sony KDL-32L504 - 32" Class Bravia L Series Lcd... Bedienungsanleitung

Sony

Sony WS-WV10 Kurzanleitung

Sony

Sony SU-WL450 Service-Handbuch

Sony

Sony CMT-L1 - Micro Hi Fi Component System Bedienungsanleitung

Sony

Sony BW-A10 Handbuch

Sony

Sony RHT-G15 Bedienungsanleitung

Sony

Sony RMM-131 Bedienungsanleitung

Sony

Sony SU-RG11M Bedienungsanleitung

Sony

Sony WS-FV10D Bedienungsanleitung

Sony

Sony SU-WL450 Service-Handbuch

Sony

Sony ACY-RK81 Bedienungsanleitung

Sony

Sony LSPX-PS1 Bedienungsanleitung

Sony

Sony SFM1 Bedienungsanleitung

Sony

Sony RHT-G5 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung