Sony SU-WL500 Instructions (SU-WL500 Wall-Mount... Bedienungsanleitung

D-410-100-12(1)

To Customers and Sony Dealers

Wall-Mount Bracket

Installation Manual

Manuel d’installation

Manual de instalación

Installatiehandleiding

Installationsanleitung

Manual de Instalação

Manuale di installazione

Installationshandbok

Installationsvejledning

Asennusohje

Installasjonsveiledning

Instrukcja instalacji

Εγχειρίδιο εγκατάστασης

Montaj Kılavuzu

Руководство по установке

Instalační příručka

Návod na inštaláciu

Szerelési útmutató

Manual de instalare

Ръководство за монтаж

Paigaldusjuhend

Uzstādīšanas rokasgrāmata

Montavimo vadovas

Priručnik za postavljanje

Priročnik za namestitev

Priručnik za postavljanje

ª±´¤£²¨

SU-WL500

2 (GB)

Thank you for purchasing this product.

If the safety precautions are not observed or the

product is used incorrectly, it may result in serious

injury or fire.

This manual shows the correct handling of the

product and important precautions necessary to

prevent accidents. Be sure to read this manual

thoroughly and use the product correctly. Keep this

manual available for future reference.

To Sony dealers

Sufficient expertise is required for installing this

product. Be sure to read this manual thoroughly to do

the installation work safely. Sony is not liable for any

damages or injury caused by mishandling or

improper installation. Please give this manual to the

customer after installation.

Products by Sony are designed with safety in mind. If

the products are used incorrectly, however, it may

result in a serious injury through fire, electric shock,

the product toppling over, or the product dropping.

Be sure to observe the precautions for safety to

prevent such accidents.

Specified products

The following products are subject to change

without notice, may be out of stock, or

discontinued.

Some models may not be available in certain

regions.

To Customers

Sufficient expertise is required for installing this

product. Be sure to subcontract the installation to

Sony dealers or licensed contractors and pay

special attention to safety during the installation.

Sony is not liable for any damages or injury

caused by mishandling or improper installation, or

installing any other than the specified product.

Your Statutory Rights (if any) are not affected.

WARNING

On Safety

CAUTION

LCD Colour monitor

FW-85BZ35F

FW-75BZ35F

FW-65BZ35F

FW-55BZ35F

FW-49BZ35F

FW-43BZ35F

3 (GB)

English

There are 4 types of installation. It may not be possible to install some types of monitors. Check the following

and install your monitor in the adequate way.

To install the monitor to the wall, the SU-WL500 Wall-Mount Bracket is necessary. Screws and spacers listed

below are also necessary depending on the way of installation.

For further details/terms & conditions, contact the sales representative for professional use.

*1 You cannot install the monitor other than the noted types.

*2 For the monitor with , the following are necessary.

Spacer: a washer with an outside diameter of 18 mm, inside diameter of 10 mm, and thickness of 2 mm

(SONY Part Number 7-688-000-32) × 20

Screw: PSW M6 × 25 mm (SONY Part Number 4-577-326-01) × 4 (1 pk)

*3 Make brightness setting to Standard or Custom 37 and lower.

*4 When installing FW-49BZ35F or FW-43BZ35F in portrait orientation, a portion of the Base Bracket is not

hidden behind the monitor.

A: Landscape, -20° leaning B: Landscape, +60° leaning C: Portrait, no leaning D: Portrait, +20° leaning

Monitor model Installation type*1 Spacer*2 Wall-Mount Bracket

Model Qty

FW-85BZ35F

FW-75BZ35F C

SU-WL500 1

FW-65BZ35F

FW-55BZ35F

FW-49BZ35F*3

C*4

D*4

FW-43BZ35F C*4

D*4

4 (GB)

Be sure to read thoroughly the all safety information

described in the instruction manual of SU-WL500.

Do NOT use SU-WL450 for installation in the way

noted in this manual.

Provide adequate clearances

around the monitor.

The following illustration shows how much space is

required around the monitor.

Be sure to install the monitor in the orientation

shown in the following illustration.

Landscape

Portrait

Do not block the ventilation holes of

the monitor.

If you block the ventilation holes with tapes or other

objects, heat builds up inside the monitor and may

cause a fire.

• If you cover the illumination LED and its

surroundings with tapes or other objects, the

status of the monitor cannot be recognized and

the remote control may not work.

• When carrying the monitor, hold it in landscape

orientation, and take care not to drop it when

installing. Do not apply excessive force to the

monitor; otherwise, it may be deformed.

• Operating temperature: 35 °C and lower

WARNING

If the following precautions are not observed,

serious injury or death through fire, electric

shock, the product toppling over, or the

product dropping can result.

Unit: mm

300

100 100

100

Unit: mm

300100

100 100

Others

5 (GB)

Follow Step 1 in the SU-WL500 instruction manual to

check the parts.

Follow Step 2 in the SU-WL500 instruction manual to

decide on the installation location. Refer to page 19

of this manual for the monitor installation dimension

table.

Follow Step 3 in the SU-WL500 instruction manual to

install the Base Bracket.

A: landscape, -20° leaning

Step 1:

Checking the parts

required for the

installation

Step 2:

Deciding on the

installation location

Step 3:

Installing the Base

Bracket on the wall

Step 4:

Preparing for the

installation of the

monitor

1Remove the stands if they are

installed to the monitor (FW-

49BZ35F only).

Be sure to lay down the monitor on a soft cloth

to protect the monitor. The installation of the

Mounting Hook is also done with the monitor

laid down.

FW-49BZ35F

When using an electric screwdriver, set the torque

setting to approximately 2 N·m {20 kgf·cm}.

Do not lift the Mounting Hook before the screws

(two screws each for left/right) are secured. This

may distort the Mounting Hook or the monitor

cabinet.

6 (GB)

2Remove the screws from the

rear of the monitor.

FW-65BZ35F/FW-55BZ35F

FW-49BZ35F

Note

Be sure to store the removed screws in a safe place,

keeping them away from children. When attaching

the stands to the monitor again, be sure to install the

stored screws back in the original position.

3Referring to the Screw and Hook

locations diagram/table on

page 21, determine the screw

positions, and secure the

Mounting Hook to the rear of the

monitor.

Secure the Mounting Hook to the rear of the

monitor temporarily, using the four screws

(+PSW6 × 16).

Be sure that both screws are securely

tightened with equal torque strength to the

rear of the monitor.

FW-65BZ35F/FW-55BZ35F

FW-49BZ35F

Mounting Hook Screw

(+PSW6 × 16)

Mounting Hook

Screw

(+PSW6 × 16)

7 (GB)

4Adjust the angle of the

Mounting Hook with the

supplied hex key.

Perform following and . Make sure that

screw firmly secures the arm base of the

Mounting Hook (both left and right).

Remove the 2 screws from the arm base

of the Mounting Hook (both left and right)

and determine the screw holes for the angle

(20°) you plan to change to.

Fit screw holes of the upper arm and

lower arm in an adequate angle, put

screws removed in step into the holes,

then secure both arms.

Notes

• Make sure that the adjusted angle of both arms are

the same.

• Make sure that both arms are screwed in securely.

CAUTION

• Be careful not to get your fingers caught while

adjusting the angle.

Hex key

FW-65BZ35F/FW-55BZ35F

FW-49BZ35F

5Remove the screws for the

stands from the monitor (FW-

65BZ35F/FW-55BZ35F only).

Since the stands are removed when you hold up

the monitor, be sure to hold the monitor

securely so that the monitor does not fall down.

FW-65BZ35F/FW-55BZ35F

8 (GB)

Step 5:

Installing the monitor

on the wall

WARNING

Be sure to complete the installation before

connecting the AC power cord to the wall outlet. If

you allow the AC power cord to be pinched under

or between pieces of equipment, this may result

in a short circuit or an electric shock.

Be careful not to stumble over the AC power cord

or the monitor, as you may hurt yourself.

1Connect the AC power cord and

the connecting cable(s) supplied

with the monitor to the monitor.

Connect the AC power cord and the connecting

cable(s) to the connectors on the rear of the

monitor. For details on connecting the AC power

cord and the connecting cable(s), refer to the

instruction manual of the monitor.

Notes

• You cannot connect the cables to the monitor after

installing it on the Base Bracket.

• Subcontract the cable routing in the wall to a

licensed contractor.

2Install the monitor onto the Base

Bracket.

Referring to the Screw and Hook locations

diagram/table on page 21, determine the

holes of the Base Bracket for latching the

upper hooks of the Mounting Hook.

Hold the monitor securely with both hands,

and gently align it on the wall.

WARNING

• Be sure that two or more persons hold the monitor

when carrying it.

• When carrying the monitor, hold it in landscape

orientation, and take care not to drop it when

installing. Do not apply excessive force to the

monitor; otherwise, it may be deformed.

Base Bracket

Mounting Hook

9 (GB)

Follow the instructions in the SU-WL500 instruction

manual to confirm.

Follow the instructions in the SU-WL500 instruction

manual to remove.

3Firmly secure the monitor and

the Base Bracket using the

screws supplied with SU-WL500

(+BVST4 × 12).

Note

When using an electric screwdriver, set the torque

setting to approximately 1.5 N·m {15 kgf·cm}.

Confirming the

completion of the

installation

When removing the

monitor

Screw

(+BVST4 × 12)

WARNING

Be sure to tighten the securing screw firmly.

If you fail to do so, the monitor may fall

when it is pushed upward and cause injury.

10 (GB)

Follow Step 1 in the SU-WL500 instruction manual to

check the parts.

Follow Step 2 in the SU-WL500 instruction manual to

decide on the installation location. Refer to page 19

of this manual for the monitor installation dimension

table.

Follow Step 3 in the SU-WL500 instruction manual to

install the Base Bracket.

B: landscape, +60° leaning

Step 1:

Checking the parts

required for the

installation

Step 2:

Deciding on the

installation location

Step 3:

Installing the Base

Bracket on the wall or

mounting

Step 4:

Preparing for the

installation of the

monitor

1Remove the stands if they are

installed to the monitor (FW-

49BZ35F only).

Be sure to lay down the monitor on a soft cloth

to protect the monitor. The installation of the

Mounting Hook is also done with the monitor

laid down.

FW-49BZ35F

When using an electric screwdriver, set the torque

setting to approximately 2 N·m {20 kgf·cm}.

Do not lift the Mounting Hook before the screws

(two screws each for left/right) are secured. This

may distort the Mounting Hook or the monitor

cabinet.

Andere Handbücher für SU-WL500 Instructions (SU-WL500 Wall-Mount...

Inhaltsverzeichnis

Sprachen:

Andere Sony Rack & Stand Handbücher

Sony

Sony SU-46NX1 Bedienungsanleitung

Sony

Sony DMBK-R3012 Bedienungsanleitung

Sony

Sony SU-WL850 Service-Handbuch

Sony

Sony SU-PF1 Bedienungsanleitung

Sony

Sony SUFL71M - SU - Stand Bedienungsanleitung

Sony

Sony SU-560 Bedienungsanleitung

Sony

Sony RHT-G15 Bedienungsanleitung

Sony

Sony SU-556 Bedienungsanleitung

Sony

Sony SU-34XBR3 Bedienungsanleitung

Sony

Sony VCT-HM1 Bedienungsanleitung

Sony

Sony SURS51U - Stand For Rear Projection TV Bedienungsanleitung

Sony

Sony SU-WL450 Service-Handbuch

Sony

Sony WS-DAVLFS Bedienungsanleitung

Sony

Sony KDL-32EX301 - 32" Class Bravia Ex301 Hdtv Betriebsanleitung

Sony

Sony SPM-42BSA Benutzerhandbuch

Sony

Sony SU-B400S Bedienungsanleitung

Sony

Sony SU-WL450 Service-Handbuch

Sony

Sony SU-27F2 Bedienungsanleitung

Sony

Sony SU-43T4 Bedienungsanleitung

Sony

Sony SU-RG11MA Bedienungsanleitung

Sony

Sony Operating Instructions SU-EF41 Bedienungsanleitung

Sony

Sony SU-P50T2 Bedienungsanleitung

Sony

Sony SU-WL11 Bedienungsanleitung

Sony

Sony SU-W110 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung