Sony SU-WL500 Instructions (SU-WL500 Wall-Mount... Bedienungsanleitung

C-644-100-12(1)

To Customers and Sony Dealers

Wall-Mount Bracket

Installation Manual

Manuel d’installation

Manual de instalación

SU-WL500

2 (GB)

Thank you for purchasing this product.

If the safety precautions are not observed or the

product is used incorrectly, it may result in serious

injury or fire.

This manual shows the correct handling of the

product and important precautions necessary to

prevent accidents. Be sure to read this manual

thoroughly and use the product correctly. Keep this

manual available for future reference.

To Sony dealers

Sufficient expertise is required for installing this

product. Be sure to read this manual thoroughly to do

the installation work safely. Sony is not liable for any

damages or injury caused by mishandling or

improper installation. Please give this manual to the

customer after installation.

Products by Sony are designed with safety in mind. If

the products are used incorrectly, however, it may

result in a serious injury through fire, electric shock,

the product toppling over, or the product dropping.

Be sure to observe the precautions for safety to

prevent such accidents.

Specified products

The following products are subject to change

without notice, may be out of stock, or

discontinued.

Some models may not be available in certain

regions.

To Customers

Sufficient expertise is required for installing this

product. Be sure to subcontract the installation to

Sony dealers or licensed contractors and pay

special attention to safety during the installation.

Sony is not liable for any damages or injury

caused by mishandling or improper installation, or

installing any other than the specified product.

Your Statutory Rights (if any) are not affected.

WARNING

On Safety

CAUTION

LCD Color TV

XBR-75X900E

XBR-65X900E

XBR-55X900E

XBR-49X900E

XBR-75X850E

XBR-65X850E

XBR-55X800E

XBR-49X800E

XBR-43X800E

KD-75X9000E

KD-65X9000E

KD-55X9000E

KD-49X9000E

KD-75X8500E

KD-65X8500E

KD-55X8500E

KD-49X8000E

KD-43X8000E

3 (GB)

English

There are 4 types of installation. It may not be possible to install some types of TVs. Check the following and

install your TV in the adequate way.

AC adaptor holder kit SU-AH1 is not be able to installed.

To install the TV to the wall, the SU-WL500 Wall Mount Bracket is necessary. Screws and spacers listed below are

also necessary depending on the way of installation.

For further details/terms & conditions, contact the sales representative for professional use.

*1 You cannot install the TV other than the noted types.

*2 For the TV with , the following are neccesary.

Spacer: a washer with an outside diameter of 18 mm, inside diameter of 10 mm, and thickness of 2 mm

(SONY Part Number 7-688-000-32) × 20

Screw: PSW M6 × 25 mm (SONY Part Number 4-577-326-01) × 4 (1 pk)

*3 Make brightness setting to Standard or Custom 45 and lower.

*4 Make brightness setting of KD-55X8500E to Standard or Custom 30 and lower.

*5 Make brightness setting to Standard or Custom 35 and lower.

A: Landscape, -20° leaning B: Landscape, +60° leaning C: Portrait, no leaning D: Portrait, +20° leaning

TV model Installation type*1 Spacer*2 Wall-Mount Bracket

Model Qty

XBR-75X900E KD-75X9000E A

SU-WL500 1

C

XBR-65X900E

XBR-55X900E

XBR-49X900E

KD-65X9000E

KD-55X9000E

KD-49X9000E

C

XBR-75X850E KD-75X8500E A

B*3

XBR-65X850E KD-65X8500E

KD-55X8500E

A

B

C*4

D*4

XBR-55X800E

XBR-49X800E KD-49X8000E

A*5

B*5

C*5

D*5

XBR-43X800E KD-43X8000E

C*5

D*5

4 (GB)

Be sure to read thoroughly the all safety information

described in the instruction manual of SU-WL500.

Do NOT use SU-WL450 for installation in the way

noted in this manual.

Provide adequate clearances

around the TV.

The following illustration shows how much space is

required around the TV.

Be sure to install the TV in the orientation shown in

the following illustration.

Landscape

Portrait

Do not block the ventilation holes of

the TV.

If you block the ventilation holes with tapes or other

objects, heat builds up inside the TV and may cause a

fire.

• When installing in portrait orientation, only the

following input/output jacks are available:

– HDMI IN 1/2/3/4 (Support 4K resolution, HDCP

2.2-compatible)

– DIGITAL AUDIO OUT (OPTICAL)

–AUDIOOUT /(Stereo mini jack)

– USB 1/2, USB 3

–LAN

– HDMI1 AUDIO IN (There may be no jack

depending on the country or region.)

• If you cover the illumination LED and its

surroundings with tapes or other objects, the

status of the TV cannot be recognized and the

remote control may not work.

• When carrying the TV, hold it in landscape

orientation, and take care not to drop it when

installing. Do not apply excessive force to the TV;

otherwise, it may be deformed.

WARNING

If the following precautions are not observed,

serious injury or death through fire, electric

shock, the product toppling over, or the

product dropping can result.

Unit: mm (inches)

300

(11 7/8)

100

(4)

100

(4)

100

(4)

Unit: mm (inches)

300

(11 7/8)

100

(4)

100

(4)

100

(4)

Others

5 (GB)

Follow Step 1 in the SU-WL500 instruction manual to

check the parts.

Follow Step 2 in the SU-WL500 instruction manual to

decide on the installation location. Refer to page 18

of this manual for the TV installation dimension table.

Follow Step 3 in the SU-WL500 instruction manual to

install the Base Bracket.

A: landscape, -20° leaning

Step 1:

Checking the parts

required for the

installation

Step 2:

Deciding on the

installation location

Step 3:

Installing the Base

Bracket on the wall

Step 4:

Preparing for the

installation of the TV

1Remove the stand if it is

installed to the TV.

Lay down the TV and lay a soft cloth under the

TV to protect the TV monitor.

XBR-75X900E/XBR-65X900E/XBR-55X900E/

XBR-49X900E/XBR-75X850E/XBR-65X850E/

XBR-55X800E/KD-75X9000E/KD-65X9000E/

KD-55X9000E/KD-49X9000E/KD-75X8500E/

KD-65X8500E/KD-55X8500E

XBR-49X800E/KD-49X8000E

When using an electric screwdriver, set the torque

setting to approximately 2 N·m {20 kgf·cm}.

Do not lift the Mounting Hook before the screws

(two screws each for left/right) are secured. This

may distort the Mounting Hook or the TV cabinet.

6 (GB)

2Remove the screws from the

rear of the TV.

XBR-75X900E/XBR-65X900E/XBR-55X900E/

XBR-49X900E/XBR-65X850E/KD-75X9000E/

KD-65X9000E/KD-55X9000E/KD-49X9000E/

KD-65X8500E/KD-55X8500E

XBR-75X850E/KD-75X8500E

3Referring to the Screw and Hook

locations diagram/table on

page 20, determine the screw

positions, and secure the

Mounting Hook to the rear of the

TV.

Secure the Mounting Hook to the rear of the

TV temporarily, using the four screws (*1, *2).

Be sure that both screws are securely

tightened with equal torque strength to the

rear of the TV.

*1 Needs 5 spacers (not supplied) and screws

PSW M6 × 25 mm (not supplied):

XBR-75X900E/XBR-75X850E/XBR-65X850E/

KD-75X9000E/KD-75X8500E/KD-65X8500E/

KD-55X8500E

*2 No spacers necessary, but screws of PSW 6 ×

16 mm are necessary (supplied):

XBR-65X900E/XBR-55X900E/XBR-49X900E/

XBR-55X800E/XBR-49X800E/KD-65X9000E/

KD-55X9000E/KD-49X9000E/KD-49X8000E

Mounting Hook

Screw*1, *2

Spacer*1, *2

10 mm (13/32 inch)

7 (GB)

4Adjust the angle of the

Mounting Hook with the

supplied hex key.

Perform following and . Make sure that

screw firmly secures the arm base of the

Mounting Hook (both left and right).

Remove the 2 screws from the arm base

of the Mounting Hook (both left and right)

and determine the screw holes for the angle

(20°) you plan to change to.

Fit screw holes of the upper arm and

lower arm in an adequate angle, put

screws removed in step into the holes,

then secure both arms.

Notes

• Make sure that the adjusted angle of both arms are

the same.

• Make sure that both arms are screwed in securely.

CAUTION

• Be careful not to get your fingers caught while

adjusting the angle.

Hex key

Step 5:

Installing the TV on the

wall

WARNING

Be sure to complete the installation before

connecting the AC power cord to the wall outlet. If

you allow the AC power cord to be pinched under

or between pieces of equipment, this may result

in a short circuit or an electric shock.

Be careful not to stumble over the AC power cord

or the TV, as you may hurt yourself.

1Connect the AC power cord and

the connecting cable(s) supplied

with the TV to the TV.

Connect the AC power cord and the connecting

cable(s) to the connectors on the rear of the TV.

For details on connecting the AC power cord

and the connecting cable(s), refer to the

instruction manual of the TV.

Notes

• You cannot connect the cables to the TV after

installing it on the Base Bracket.

• Subcontract the cable routing in the wall to a

licensed contractor.

8 (GB)

Follow the instructions in the SU-WL500 instruction

manual to confirm.

Follow the instructions in the SU-WL500 instruction

manual to remove.

2Install the TV onto the Base

Bracket.

Referring to the Screw and Hook locations

diagram/table on page 20, determine the

holes of the Base Bracket for latching the

upper hooks of the Mounting Hook.

Hold the TV securely with both hands, and

gently align it on the wall.

WARNING

• Be sure that two or more persons hold the TV when

carrying it.

• When carrying the TV, hold it in landscape

orientation, and take care not to drop it when

installing. Do not apply excessive force to the TV;

otherwise, it may be deformed.

Base Bracket

Mounting Hook

3Firmly secure the TV and the

Base Bracket using the screw

supplied with SU-WL500

(+BVST4 × 12).

Note

When using an electric screwdriver, set the torque

setting to approximately 1.5 N·m {15 kgf·cm}.

Confirming the

completion of the

installation

When removing the TV

Screw

(+BVST4 × 12)

WARNING

Be sure to tighten the securing screw firmly.

If you fail to do so, the TV may fall when it is

pushed upward and cause injury.

9 (GB)

Follow Step 1 in the SU-WL500 instruction manual to

check the parts.

Follow Step 2 in the SU-WL500 instruction manual to

decide on the installation location. Refer to page 18

of this manual for the TV installation dimension table.

Follow Step 3 in the SU-WL500 instruction manual to

install the Base Bracket.

B: landscape, +60° leaning

Step 1:

Checking the parts

required for the

installation

Step 2:

Deciding on the

installation location

Step 3:

Installing the Base

Bracket on the wall or

mounting

Step 4:

Preparing for the

installation of the TV

1Remove the stand if it is

installed to the TV.

Lay down the TV and lay a soft cloth under the

TV to protect the TV monitor.

XBR-75X850E/XBR-65X850E/XBR-55X800E/

KD-75X8500E/KD-65X8500E/KD-55X8500E

XBR-49X800E/KD-49X8000E

When using an electric screwdriver, set the torque

setting to approximately 2 N·m {20 kgf·cm}.

Do not lift the Mounting Hook before the screws

(two screws each for left/right) are secured. This

may distort the Mounting Hook or the TV cabinet.

10 (GB)

2Remove the screws from the

rear of the TV.

XBR-65X850E/KD-65X8500E/KD-55X8500E

XBR-75X850E/KD-75X8500E

3Referring to the Screw and Hook

locations diagram/table on

page 20, determine the screw

positions, and secure the

Mounting Hook to the rear of the

TV.

Secure the Mounting Hook to the rear of the

TV temporarily, using the four screws (*1, *2).

Be sure that both screws are securely

tightened with equal torque strength to the

rear of the TV.

*1 Needs 5 spacers (not supplied) and screws

PSW M6 × 25 mm (not supplied):

XBR-65X850E/KD-65X8500E/KD-55X8500E

*2 No spacers necessary, but screws of PSW 6 ×

16 mm are necessary (supplied):

XBR-75X850E/XBR-55X800E/XBR-49X800E/

KD-75X8500E/KD-49X8000E

Mounting Hook

Screw*1, *2

Spacer*1, *2

10 mm (13/32 inch)

Andere Handbücher für SU-WL500 Instructions (SU-WL500 Wall-Mount...

Inhaltsverzeichnis

Sprachen:

Andere Sony Rack & Stand Handbücher

Sony

Sony SU-WL450 Service-Handbuch

Sony

Sony SUFL71M - SU - Stand Bedienungsanleitung

Sony

Sony SU-WL51 Bedienungsanleitung

Sony

Sony SU-RG11S Bedienungsanleitung

Sony

Sony PROFORMA460AB Bedienungsanleitung

Sony

Sony SU-B551S Bedienungsanleitung

Sony

Sony SFM1 Bedienungsanleitung

Sony

Sony SU-P50T2 Bedienungsanleitung

Sony

Sony SU-GW3 Benutzerhandbuch

Sony

Sony Bravia XBR-84X900 Leitfaden

Sony

Sony SU-WL850 Service-Handbuch

Sony

Sony STR-DH830 Bedienungsanleitung

Sony

Sony WS-FV10 Bedienungsanleitung

Sony

Sony MB-L22 Bedienungsanleitung

Sony

Sony WSFV11 Gebrauchs- und Wartungshandbuch

Sony

Sony SU-GW3 Bedienungsanleitung

Sony

Sony SU-RG13M Bedienungsanleitung

Sony

Sony KDL-32EX301 - 32" Class Bravia Ex301 Hdtv Betriebsanleitung

Sony

Sony SU-W200 Bedienungsanleitung

Sony

Sony SU-43T4 Bedienungsanleitung

Sony

Sony BKM-30E20 Bedienungsanleitung

Sony

Sony SU-32F2 Bedienungsanleitung

Sony

Sony SU-GW12 Bedienungsanleitung

Sony

Sony SU-SX10 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung