SoundCraft 328xd Bedienungsanleitung

RIGHT

STE-2STE-1

SELECT

MUTE

SOLO

MIX

dBFS

0dBFS = 18dBu

STEREO INPUTS

GROUP LINK

CHANNEL /

XDX D

EXIT

PARAMETER

FUNCTION

OUT

THRU

MIDI

IN OUT IN

OUT

S/PDIF

OUT IN

AES/EBU

WORD

CLOCK CLOCK

WORD/SUPER

ALESIS ADAT AND BRC

328

Soundcraft 328XD and Alesis ADAT and BRC

328XD AND

328XD AND328XD AND

328XD AND

ALESIS ADAT

ALESIS ADATALESIS ADAT

ALESIS ADAT

AND BRC

AND BRCAND BRC

AND BRC

Connecting the system 2

328XD Configuration 4

BRC and ADAT Configuration 6

Notes on single ADAT operation 8

Soundcraft 328XD and Alesis ADAT and BRC

CONNECTING THE SYSTEM

Audio Connections

Connect audio connections as shown in the diagram below. ADAT Optical cables must be connected from

the ADAT Out ports of both the ADATs to the ADAT In ports of the 328XD and vice versa.

The ADAT connections allow digital transfer of either direct outputs for input channels 1-16 to the ADATs,

or the 328XD’s 8 Group outputs.

Synchronization Connections

Besides the audio connections, a BNC Wordclock cable must be connected from the 328XD Wordclock

Out to the BRC 48kHz input to synchronize the transmission of the samples.

NOTE:

It must be decided whether MIDI Time Code (MTC) or Longitudinal Timecode (LTC or SMPTE) is

to be used to transmit the timecode from the BRC to the 328XD. If LTC is to be used, MIDI

connections must still be made, in order to enable the transmission of MIDI Machine Control

(MMC). MMC is responsible for the transmission of the Transport and Locate Controls between

BRC and 328XD.

Soundcraft 328XD and Alesis ADAT and BRC

In the following diagram the MIDI cable from the BRC MIDI Out port is used to transmit the MIDI

Timecode to the 328XD.

To summarize, the connections required are as follows:

BNC Wordclock cable:

328XD Wordclock out

BRC Wordclock In

MIDI Cables (required even if MIDI Timecode is not to be used):

328XD MIDI Out

BRC MIDI In

BRC MIDI Out

328XD MIDI In

SMPTE Cable (required only if SMPTE is to be used instead of MIDI Timecode)

BRC Timecode Out

328XD Timecode In

Alesis Sync Cables:

BRC Sync Out

ADAT Master SyncIn ADAT

Master SyncOut

ADAT Client Sync In

Optical Cables:

ADAT Master Optical Out

328XD 8 Track A Optical In

328XD 8 Track A Optical Out

ADAT Master Optical In

ADAT Client Optical Out

328XD 8 Track B Optical In

328XD 8 Track B Optical Out

ADAT Client Optical In

Soundcraft 328XD and Alesis ADAT and BRC

328XD CONFIGURATION

Wordclock

In a configuration using the BRC, the 328XD must be made to be the wordclock master device. Enter the

328XD Menu pages by pressing the <MENU> button on the right hand side of the LCD display. Using

the encoder beneath the display, scroll up or down until the ‘Clock Source Sel’ menu is highlighted, and

press <ENTER>. Here, either the internal sampling rate can be toggled between 44.1kHz and 48kHz.

As the BRC responds only to a 48kHz input, the 328XD must be set to Internal Clock at 48kHz. Use the

encoder to set the clock to 48kHz, press <ENTER> to set the sample rate and <MENU> to return to the

menu pages.

Tape Ports

To ensure that the 328XD Tape Ports are set to ADAT, enter the 328XD Menu pages by pressing the

<MENU> button on the right hand side of the LCD display. Using the PARAM encoder beneath the

display, scroll up or down until the ‘Tape Port Select’ menu is highlighted. Press <ENTER> and keep

pressing the Up cursor arrow until the ‘<Tape Ch17-24 >’ menu page is displayed. Using the PARAM

encoder, set the Bank Source to ADAT. Press the Down cursor arrow once, to set the wordlength. Newer

ADATs such as the XT-20 or LX-20 are capable of 20-bit recording, and so for optimum results, 20-bit

wordlength can be selected here. If using the black Classic ADAT, 16-bit should be selected. The ADAT

manuals should be consulted for further information. The wordlength is set on the 328XD with the

PARAM encoder.

Press the Down cursor arrow once to set the wordlength. Newer ADATs such as the XT-20 or LX-20 are

capable of 20-bit recording, and so for optimum results, 20-bit wordlength can be selected here. If using

the black Classic ADAT, 16-bit should be selected. The ADAT manuals should be consulted for further

information. The wordlength is set on the 328XD with the PARAM encoder. Press <MENU> to return to

the menu pages.

Soundcraft 328XD and Alesis ADAT and BRC

MIDI

To configure the 328XD to send the MMC controls to the BRC and vice versa, the Alesis BRC must be

selected in the Tape Machine Setup menu. Enter the Menu pages by pressing the <MENU> button,

and scroll up or down with the PARAM encoder until the ‘Tape Mach Setup’ menu is highlighted. Press

<ENTER>, scroll until ‘Alesis BRC’ is highlighted and press <ENTER> again.

NOTE:

Once the BRC has been selected, the timecode source must be selected. If no SMPTE cable

has been connected, MTC must be selected; if a SMPTE cable has been connected, LTC

must be selected.

The frame rate must also be selected. The options are 24 frame, 25 frame, 30 drop frame and 30 non-

drop frame. Whichever is selected here must also be selected later when setting up the BRC.

Once the 328XD has been set up, it is very advisable to store a User Setup of the above settings. Enter

the Menu pages by pressing the <MENU> button and scroll through the menus until ‘User Setups’ is

highlighted. Press <ENTER> and scroll through to find a vacant setup location. Press <STORE> in the

328XD Snapshot panel. The User Setup will now be stored. To edit the parameters of the setup, while

the setup is highlighted in the display, press <ENTER>. To recall the setup, highlight it in the User

Setups menu in the LCD and press the <RECALL> button in the Snapshot panel.

NOTE:

Before proceeding to the ADAT and BRC setup, recall the User Setup as illustrated above

and switch off the 328XD.

Soundcraft 328XD and Alesis ADAT and BRC

BRC AND ADAT CONFIGURATION

Firstly, turn on theClient ADAT. Allow a fewseconds for the ADAT to boot correctly. Next turn onthe

Master ADAT. Allow afewmore seconds for the ADAT to boot and recognize theClient ADAT. Then turn

on theBRC. Ensure that theBRC recognizes both ADATs. If it does not recognize theADATs, you will

need to turn off the BRC and reinitialize it, by holding down <RECORD> and <PLAY> and turning on the

BRC. You may need to repeat this procedure until the BRC recognizes thetwo ADATs.

Once theBRC and ADATs are stable, theBRC must be set up correctly.

BRC Setup

TIMECODE

To set the BRC to Timecode generation toeither MTC or SMPTE:

MTC: Press <EDIT>, <GEN SYNC>, <GEN SYNC> on the BRC. Using the <UPPERCASE> and

<LOWERCASE> cursor keys, select MTC.

SMPTE: Press <EDIT>, <GEN SYNC> on the BRC to select SMPTE timecode output. Using the

<UPPERCASE> cursor key select +4dB.

NOTE:

SMPTE should only be selected if the SMPTE cable is connected between the BRC and the

328XD.

WORDCLOCK

Press <EXT SYNC> on the BRC. Ensure that the <EDIT> button has remained lit, and use the

<UPPERCASE> and <LOWERCASE> cursor keys until the display reads

To leave the EDIT mode, press <EDIT>

Soundcraft 328XD and Alesis ADAT and BRC

CONFIRMING THE SETTINGS

To implement the above settings made to the BRC:

Press

Then the

<GEN SYNC> (Generate Sync - MTC/SMPTE)

and

<EXT SYNC> (External Sync - Wordclock)

buttons should now be lit, indicating that the BRC is generating MIDI Timecode or SMPTE and sending it

to the 328XD, and is receiving 48kHz Wordclock from the 328XD on the BNC cable.

FRAME RATE

Press the <SMPTE> button on the BRC until the LED indicates the same Frame Rate as was selected in

the 328XD configuration.

ADAT Setup

BLACK CLASSIC ADAT:

Press <DIGITAL IN> (on both ADATs if two are connected)

LATER MODEL

Press <Digital Input> (on both ADATs if two are connected)

NOTE:

Do not do this from the BRC – the <DIGITAL I/O> button sets the BRC and connected ADATs

into track bounce mode.

To complete the setup, turn on the 328XD again.

Soundcraft 328XD and Alesis ADAT and BRC

NOTES ON SINGLE ADAT OPERATION

The 328XD should be set up as outlined above, with a few notable exceptions. As an ADAT has no MIDI

capabilities or a SMPTE output, Timecode cannot be transmitted and the 328XD Transport Controls

cannot be used. The Tape Port should be set to ADAT as above, ensuring that if only one ADAT is

connected that the unused port is set to TDIF.

The ADAT(s) should be set to Digital Input, as outlined on the previous page, and also set to receive

external clock. To set the clock to external, press the <CLOCK SELECT> button on the front panel until

DIG 48K is seen in the display.

NOTE:

If 48K flashes in the display, the ADAT tape is formatted at 44.1kHz. The 328XD should now

be set to generate wordclock at 44.1kHz (see above). The sampling rate will now remain lit on

the ADAT display.

SOUNDCRAFT

HARMAN INTERNATIONAL INDUSTRIES LTD

CRANBORNE HOUSE

CRANBORNE ROAD

POTTERS BAR

HERTS EN6 3JN UK

TEL: +44 (0) 1707 665000

FAX: +44 (0) 1707 660742

EMAIL: info@soundcraft.com

SOUNDCRAFT USA

1449 DONELSON PIKE

NASHVILLE TN 37217 USA

TEL: 1-615-360-0471

FAX: 1-615-360-0273

EMAIL: soundcraft-usa@harman.com

www.soundcraft.com

Andere Handbücher für 328xd

Andere SoundCraft Musikmixer Handbücher

SoundCraft

SoundCraft 400B Series Bedienungsanleitung

SoundCraft

SoundCraft MFX Bedienungsanleitung

SoundCraft

SoundCraft Vi4 Bedienungsanleitung

SoundCraft

SoundCraft Spirit Live 3-2 Bedienungsanleitung

SoundCraft

SoundCraft SPIRIT FOLIO Bedienungsanleitung

SoundCraft

SoundCraft Vi1 Bedienungsanleitung

SoundCraft

SoundCraft CPS800 Bedienungsanleitung

SoundCraft

SoundCraft mini Stagebox 32i Fehlerbehebungshandbuch

SoundCraft

SoundCraft K2 Bedienungsanleitung

SoundCraft

SoundCraft SPIRIT Monitor2 Bedienungsanleitung

SoundCraft

SoundCraft K1 Bedienungsanleitung

SoundCraft

SoundCraft M16 Bedienungsanleitung

SoundCraft

SoundCraft NOTEPAD 102 Bedienungsanleitung

SoundCraft

SoundCraft ZL0439 Bedienungsanleitung

SoundCraft

SoundCraft 328xd Kurzanleitung

SoundCraft

SoundCraft 200B Bedienungsanleitung

SoundCraft

SoundCraft Venue II Bedienungsanleitung

SoundCraft

SoundCraft Spirit Digital 328 v2 Bedienungsanleitung

SoundCraft

SoundCraft 200BVE Bedienungsanleitung

SoundCraft

SoundCraft Spirit M Series Bedienungsanleitung

SoundCraft

SoundCraft Si EXPRESSION Bedienungsanleitung

SoundCraft

SoundCraft SPIRIT M-Audio LAGOON Digital 328 v2 Bedienungsanleitung

SoundCraft

SoundCraft 328xd Bedienungsanleitung

SoundCraft

SoundCraft Signature 16 Bedienungsanleitung

Beliebte Musikmixer Handbücher anderer Marken

Neve

Neve 8816 Bedienungsanleitung

Mackie

Mackie Onyx Analogue Mixer Bedienungsanleitung

Behringer

Behringer EUROPOWER PMP518M Bedienungsanleitung

Peavey

Peavey S-32 Sanctuary Series Bedienungsanleitung

Rane

Rane MP 4 Bedienungsanleitung

True

True T9 Touchscreen Console Bedienungsanleitung

Studiomaster

Studiomaster Air Pro 24 Bedienungsanleitung

Pioneer

Pioneer SVM 1000 - Audio/Video Mixer Bedienungsanleitung

Roland

Roland M-160 Bedienungsanleitung

Yamaha

Yamaha MR1642 Bedienungsanleitung

Ecler

Ecler MAC40v Bedienungsanleitung

Pioneer

Pioneer DJM 909 - Battle Mixer W/Effects Bedienungsanleitung

Veeder-Root

Veeder-Root TLS-350 Series Bedienungsanleitung

Alto

Alto APM80.QUAD Bedienungsanleitung

Omnitronic

Omnitronic PM-211 Bedienungsanleitung

Roland

Roland SoundCanvas SC-8820 Bedienungsanleitung

CARVIN

CARVIN RX 1200 Bedienungsanleitung

Roland

Roland M-16E Bedienungsanleitung