SoundCraft SPIRIT M-Audio LAGOON Digital 328 v2 Bedienungsanleitung

Setup Guide

Setup GuideSetup Guide

Setup Guide

V 2.0

Lagoon

LagoonLagoon

Lagoon

Revised: 04-12-00

Lagoon Setup Guide

Contents

1 Connecting The System 2

2 Digital 328 Setup 4

3 Lagoon Setup 6

4 Using The Lagoon With The 328 10

Digital 328 v2 and

Digital 328 v2 andDigital 328 v2 and

Digital 328 v2 and

M-Audio Lagoon Setup Guide

M-Audio Lagoon Setup GuideM-Audio Lagoon Setup Guide

M-Audio Lagoon Setup Guide

Spirit Digital 328 v2

Audio connections should be made as shown in the diagram below. Toslink optical cables must

be connected both from ADAT Out port of the Lagoon card to the ADAT In port A of the Digital

328 and vice versa.

The optical plugs should remain in the Digital 328 ADAT port B input and output.

In this configuration, the ADAT connections allow digital transfer of either direct outputs from the

328’s input channels 1-8 to the Lagoon card, or the 328’s 8 Group outputs.

Connecting The System

Connecting The SystemConnecting The System

Connecting The System

Audio Connections

Audio ConnectionsAudio Connections

Audio Connections

328 ADAT Out A ÎLagoon ADAT In

Lagoon ADAT Out Î328 ADAT In A

The optical S/PDIF option for the Lagoon will be unavailable when used

with the 328 without an additional optical – coaxial S/PDIF converter.

NOTE

Before you begin to configure the setup, lower both the Digital

328 mix fader, control room and headphone output levels.

Lagoon Setup Guide

You may also wish to connect the Digital 328 to the Lagoon card with MIDI cables to allow MIDI

automation/System Exclusive dumps from the 328 to be recorded and played back from your PC.

If you wish to connect the Digital 328 MIDI I/O to the Lagoon card MIDI I/O, the following

connections must be made:

Other Connections

Other ConnectionsOther Connections

Other Connections

Lagoon MIDI Out Î328 MIDI In

328 MIDI Out ÎLagoon MIDI In

Spirit Digital 328 v2

The Lagoon card and the Digital 328 (plus any other devices in the studio setup) must have their

internal clocks synchronized to allow correct transmission and reception of digital information

throughout the system. This is achieved by configuring one of the devices as a wordclock master,

and configuring all other devices in the studio setup to slave to this wordclock, hence

synchronizing all clocks in the studio setup.

In this case, the Digital 328 will be set to wordclock master, and the Lagoon will be set to slave

to the 328, via the Lagoon ADAT input – see section 3, Lagoon Setup. Any other devices

interfacing digitally with the 328 within the studio setup will also be configured to slave to the

328’s wordclock.

To configure the Digital 328 as the wordclock master, enter the 328’s Main Menu page by

pressing the <MENU> button to the right hand side of the LCD display. Using the rotary

encoder beneath the display, scroll up or down until the ‘Clock Source Sel’ menu is highlighted,

and press <ENTER>. Here, either ‘Internal: 44.1kHz’ or ‘Internal: 48kHz’ clock must be

selected for the 328 to function as wordclock master. Set this to the samplerate you wish to work

at then press <ENTER> to confirm the samplerate setting.

To ensure that the Digital 328 Tape Port A is configured to ‘ADAT’ to work with the Lagoon, enter

the 328 Menu pages by pressing the <MENU> button to the right hand side of the LCD display.

Using the rotary encoder beneath the display, scroll up or down until the ‘Tape Port Select’ menu

is highlighted and press <ENTER>.

Now repeatedly press the Up cursor arrow until the ‘<Tape Ch17-24 >’ menu page is displayed.

Using the rotary encoder set the ‘Bank Source’ to ‘ADAT’:

Tape Port Setup

Tape Port SetupTape Port Setup

Tape Port Setup

rc.

Internal:44.1kHz

rc.

Internal:48.0kHz

2Digital 328 Setup

Digital 328 SetupDigital 328 Setup

Digital 328 Setup

Wordclock information is automatically embedded into the ADAT data

stream output by the Digital 328, allowing the Lagoon to slave to the

328’s ADAT output, providing clock synchronization between the 328

and the Lagoon.

NOTE

The Lagoon cannot be configured as a clock master in a setup with the

328 as the 328 does not read the clock present at its ADAT inputs.

NOTE

Lagoon Setup Guide

Now press the Down cursor arrow once, to enable you to set the wordlength. The Lagoon is

capable of 24 bit recording, and so for optimum results, 24 bit wordlength can be selected here.

If your audio sequencer supports only 16 or 20 bit resolution, make this setting here – check

your sequencer manual for more information.

Set the desired wordlength on the 328 with the rotary encoder.

Wordlen

th: 24

Bank Source:ADAT

In a setup with the Lagoon connected to Digital 328 ADAT input and

output A, Tape Port B should be left set to TDIF. Alternatively, the

Lagoon can be connected to Digital 328 ADAT input and output B, and

Tape Port A set to TDIF. In this case, the above settings should be

made to Tape Port B.

NOTE

Spirit Digital 328 v2

To set up the Lagoon for connection to the 328, first click on the Lagoon Tools icon on the

Windows taskbar:

The Lagoon Tools application should open. Click on the ‘General’ tab. The following window

should open. Set both the input and output to be ADAT format:

Input Setup

Input SetupInput Setup

Input Setup

3Lagoon Setup

Lagoon SetupLagoon Setup

Lagoon Setup

Lagoon Setup Guide

The Lagoon clock source must then be set so that its internal clock is slaved to the incoming

ADAT wordclock output from the 328. Set ‘Clock Source’ to ‘Optical In’:

The Lagoon card will automatically detect the sample rate at the ADAT input, and so to alter the

sample rate, the 328 internal clock frequency should be adjusted - see page 4.

The ‘T2S’ filter should be left unchecked as the Digital 328 is fitted with

Toshiba optical receivers and transmitters.

NOTE

The Lagoon cannot be configured as a clock master in a setup with the

328 as the 328 does not read the clock present at its ADAT inputs.

NOTE

Spirit Digital 328 v2

Click on the MIDI tab within the Lagoon Tools application, and enable the Lagoon MIDI input and

output ports:

The Lagoon MIDI input and output ports should be selected within your chosen MIDI sequencer

to enable record and playback of 328 automation data. Check the Digital 328 automation guides

available for popular sequencers for more information.

MIDI Setup

MIDI SetupMIDI Setup

MIDI Setup

Lagoon Setup Guide

Until the Lagoon is set to synchronize to the 328 master wordclock (page 7), the clocks will run

out of sync. Spurious clicks and pops or distorted audio may well be heard as a result. While

configuring the system then, it is likely that the Lagoon will have registered wordclock

synchronization errors. To reset the Lagoon, click on the Lagoon Tools ‘Status’ tab, and then the

‘Clear all errors’ button:

If any of the error LEDs light or remain lit, check that the ADAT connections and 328 and Lagoon

Tools settings are correct.

Clear All Errors

Clear All ErrorsClear All Errors

Clear All Errors

Once the Lagoon registers no errors, the Lagoon and Digital 328

clocks are synchronized. The 328 mix fader, control room and

headphone output levels may be raised.

Andere SoundCraft Musikmixer Handbücher

SoundCraft

SoundCraft 328xd Bedienungsanleitung

SoundCraft

SoundCraft B400 Bedienungsanleitung

SoundCraft

SoundCraft Si EXPRESSION Bedienungsanleitung

SoundCraft

SoundCraft SM 16 Bedienungsanleitung

SoundCraft

SoundCraft Spirit Live 4 Bedienungsanleitung

SoundCraft

SoundCraft UREI 1620LE Bedienungsanleitung

SoundCraft

SoundCraft 200 Delta Bedienungsanleitung

SoundCraft

SoundCraft RM105 Bedienungsanleitung

SoundCraft

SoundCraft Si Performer Bedienungsanleitung

SoundCraft

SoundCraft D-MIX 1000 Bedienungsanleitung

SoundCraft

SoundCraft GB8 Bedienungsanleitung

SoundCraft

SoundCraft 400B Series Bedienungsanleitung

SoundCraft

SoundCraft Spirit Live 4 Bedienungsanleitung

SoundCraft

SoundCraft 1603 Bedienungsanleitung

SoundCraft

SoundCraft 328xd Bedienungsanleitung

SoundCraft

SoundCraft Spirit Digital 328 Montage- und Bedienungsanleitung

SoundCraft

SoundCraft Vienna II Bedienungsanleitung

SoundCraft

SoundCraft Notepad 5 Bedienungsanleitung

SoundCraft

SoundCraft Four Series Bedienungsanleitung

SoundCraft

SoundCraft SPIRIT Monitor2 Bedienungsanleitung

SoundCraft

SoundCraft Spirit M Series Bedienungsanleitung

SoundCraft

SoundCraft MBI 10 Series Bedienungsanleitung

SoundCraft

SoundCraft 200SR Bedienungsanleitung

SoundCraft

SoundCraft Signature 16 Bedienungsanleitung

Beliebte Musikmixer Handbücher anderer Marken

Neve

Neve 8816 Bedienungsanleitung

Mackie

Mackie Onyx Analogue Mixer Bedienungsanleitung

Behringer

Behringer EUROPOWER PMP518M Bedienungsanleitung

Peavey

Peavey S-32 Sanctuary Series Bedienungsanleitung

Rane

Rane MP 4 Bedienungsanleitung

True

True T9 Touchscreen Console Bedienungsanleitung

Studiomaster

Studiomaster Air Pro 24 Bedienungsanleitung

Pioneer

Pioneer SVM 1000 - Audio/Video Mixer Bedienungsanleitung

Roland

Roland M-160 Bedienungsanleitung

Yamaha

Yamaha MR1642 Bedienungsanleitung

Ecler

Ecler MAC40v Bedienungsanleitung

Pioneer

Pioneer DJM 909 - Battle Mixer W/Effects Bedienungsanleitung

Veeder-Root

Veeder-Root TLS-350 Series Bedienungsanleitung

Alto

Alto APM80.QUAD Bedienungsanleitung

Omnitronic

Omnitronic PM-211 Bedienungsanleitung

Roland

Roland SoundCanvas SC-8820 Bedienungsanleitung

CARVIN

CARVIN RX 1200 Bedienungsanleitung

Roland

Roland M-16E Bedienungsanleitung