SoundCraft 328xd Bedienungsanleitung

RIGHT

STE-2STE-1

SELECT

MUTE

SOLO

MIX

dBFS

0dBFS = 18dBu

STEREO INPUTS

GROUP LINK

CHANNEL /

XDX D

EXIT

PARAMETER

FUNCTION

OUT

THRU

MIDI

IN OUT IN

OUT

S/PDIF

OUT IN

AES/EBU

WORD

CLOCK CLOCK

WORD/SUPER

M-AUDIO LAGOON

328

Soundcraft 328XD and M-Audio Lagoon

328XD AND

328XD AND328XD AND

328XD AND

M-AUDIO LAGOON

M-AUDIO LAGOONM-AUDIO LAGOON

M-AUDIO LAGOON

Connecting the system 2

328XD Configuration 3

Lagoon Configuration 5

Using the Lagoon with the 328XD 9

Additional Information 10

Soundcraft 328XD and M-Audio Lagoon

CONNECTING THE SYSTEM

Audio Connections

Audio connections should be made as shown in the diagram below. ADAT optical cables must be

connected both from ADAT Out port of the Lagoon card to the 328XD ADAT In 17-24 and vice versa.

The optical plugs should remain in the 328XD ADAT port 25-32 input and output.

In this configuration, the ADAT connections allow digital transfer of either direct outputs from the 328XD’s

input channels 1-8 to the Lagoon card, or the 328XD’s 8 Group outputs.

Other Connections

You may also wish to connect the 328XD to the Lagoon card with MIDI cables to allow MIDI automation /

System Exclusive dumps from the 328XD to be recorded and played back from your PC.

If you wish to connect the 328XD MIDI I/O to the Lagoon, the following connections must be made:

Soundcraft 328XD and M-Audio Lagoon

328XD CONFIGURATION

The Lagoon card and the 328XD (plusany otherdevices in thestudio setup) must have their internal

clocks synchronized toallow correct transmission and reception of digital information throughout the

system. This isachieved by configuring one of thedevices as awordclock host,andconfiguring all

other devices in thestudio setup to sync tothis wordclock, hence synchronizing all clocks in the

studio setup.

In this case, the328XD will be setto wordclockhost,and the Lagoon will be setto sync to the

328XD, via theLagoon ADAT input–see

Lagoon Configuration

Any other devices interfacing

digitally with the328XDwithin thestudio setupwill also be configured tosync to the328XD’s

wordclock.

NOTE:

Wordclock information is embedded into the 328XD ADAT output data stream, allowing the

Lagoon tosync to the 328XD’s ADAT output

To configure the328XD as thewordclock host,enter the 328’s Main Menu page by pressing the

<MENU> button to the right hand side of the LCD display. Using thePARAM encoder beneath the

display, scroll up or down until the ‘Clock Source Sel’ menu is highlighted, and press <ENTER>. Here,

either ‘Internal: 44.1kHz’ or‘Internal: 48kHz’ clock must be selected for the 328XD to function as

wordclock host.With thePARAM encoder set this to thesample rate you wish to work at, press

<ENTER> to confirm the sample rate setting and <MENU> to return to the menu pages.

Tape Port Setup

To ensure that the 328XD Tape Port 17-24 is configured to ‘ADAT’ to work with the Lagoon, enter the

328XD Menu pages by pressing the <MENU> button to the right hand side of the LCD display. Using

the PARAM encoder beneath the display, scroll up or down until the ‘Tape Port Select’ menu is

highlighted and press <ENTER>.

Now press the Up cursor key until the ‘<Tape Ch17-24 >’ menu page is displayed. Using the PARAM

encoder set the ‘Bank Source’ to ‘ADAT’:

The Lagoon is capable of 24 bit recording, and so for optimum results, 24 bit wordlength can be selected

here. If your audio sequencer supports only 16 or 20 bit resolution, set the wordlength appropriately–

check your sequencer manual for more information.

Set the desired wordlength on the 328XD with the PARAM encoder.

Soundcraft 328XD and M-Audio Lagoon

NOTE:

In a setup with the Lagoon connected to 328XD ADAT input and output 17-24, Tape Port 25-

32 should be left set to TDIF. Alternatively, the Lagoon can be connected to 328XD ADAT input

and output 25-32, and Tape Port 17-24 set to TDIF. In this case, the above settings should be

made to Tape Port 25-32.

Soundcraft 328XD and M-Audio Lagoon

LAGOON CONFIGURATION

Input Setup

To set up the Lagoon for connection to the 328XD, first click on the Lagoon Tools icon on the Windows

taskbar:

The Lagoon Tools application should open. Click on the ‘General’ tab. The following window should open.

Set both the input and output to be ADAT format:

Soundcraft 328XD and M-Audio Lagoon

The Lagoon clock source must then be set so that its internal clock is synchronised totheincoming

ADAT wordclock output from the328XD. Set ‘Clock Source’ to ‘Optical In’:

The Lagoon card will automatically detect the sample rate at the ADAT input, and so to alter the sample

rate, the 328XD internal clock frequency should be adjusted - see page 3.

NOTE:

The ‘T2S’ filter should be left unchecked as the 328XD is fitted with Toshiba optical receivers

and transmitters.

Soundcraft 328XD and M-Audio Lagoon

MIDI Setup

Click on the MIDI tab within the Lagoon Tools application, and enable the Lagoon MIDI input and output

ports:

The Lagoon MIDI input and output ports should be selected within your chosen MIDI sequencer to enable

record and playback of 328XD automation data.

Soundcraft 328XD and M-Audio Lagoon

Clear all Errors

Until the Lagoon is set to synchronize to the 328XD host wordclock (page 6), the clocks will run out of

sync. Spurious clicks and pops or distorted audio may well be heard asa result. While configuring the

system then, it is likely that the Lagoon will have registered wordclock synchronization errors. To reset the

Lagoon, click on theLagoon Tools ‘Status’ tab, and then the‘Clear all errors’ button:

If any of the error LEDs light or remain lit, check that the ADAT connections and 328XD and Lagoon Tools

settings are correct.

NOTE:

Once the Lagoon registers no errors, the Lagoon and 328XD clocks are synchronized. The

328XD mix fader, control room and headphone output levels may be raised.

Soundcraft 328XD and M-Audio Lagoon

USING THE LAGOON WITH THE 328XD

Accessing the Lagoon ADAT I/O from the 328XD

The Lagoon will commonly be used with a software audio sequencer / hard disk recorder to allow the

simultaneous playback and recording of 8 individual tracks of audio, via the ADAT I/O. Here, the software

application must be configured to access the Lagoon ADAT I/O using the relevant Windows device drivers

that came with the card.

When playing back audio tracks from the software application, tracks 1-8 will be accessible from

channels 17-24 respectively in the BANK SELECT 17-32 on the 328XD.

See the 328XD User Guide for full instructions on how to send a channel or group to tape / audio

sequencer. By default the 328XD is configured to send analogue input channels 1-8 directly to tape

outputs 1-8 post-fade.

NOTE:

Ensure that the relevant device drivers are fully installed for the software application to

correctly access the Lagoon ADAT I/O. Consult the Lagoon manual for more information.

Andere Handbücher für 328xd

Inhaltsverzeichnis

Andere SoundCraft Musikmixer Handbücher

SoundCraft

SoundCraft Spirit FX16 Bedienungsanleitung

SoundCraft

SoundCraft Series 2 Bedienungsanleitung

SoundCraft

SoundCraft RM1ds Bedienungsanleitung

SoundCraft

SoundCraft Vi Series Technisches Handbuch

SoundCraft

SoundCraft 328xd Bedienungsanleitung

SoundCraft

SoundCraft MINI STAGEBOX 32 Handbuch

SoundCraft

SoundCraft MPM 12/2 Bedienungsanleitung

SoundCraft

SoundCraft S6000 Bedienungsanleitung

SoundCraft

SoundCraft Spirit Digital 328 v2 Bedienungsanleitung

SoundCraft

SoundCraft GIGRAC 1000st Bedienungsanleitung

SoundCraft

SoundCraft EFX Bedienungsanleitung

SoundCraft

SoundCraft SPIRIT POWERSTATION Bedienungsanleitung

SoundCraft

SoundCraft NOTEPAD 102 Bedienungsanleitung

SoundCraft

SoundCraft Si Performer Bedienungsanleitung

SoundCraft

SoundCraft GB2 Bedienungsanleitung

SoundCraft

SoundCraft Signature 16 Bedienungsanleitung

SoundCraft

SoundCraft Si Compact Bedienungsanleitung

SoundCraft

SoundCraft 328xd Bedienungsanleitung

SoundCraft

SoundCraft Delta Theatre Bedienungsanleitung

SoundCraft

SoundCraft 200B Bedienungsanleitung

SoundCraft

SoundCraft FX16II Bedienungsanleitung

SoundCraft

SoundCraft Spirit FX16 Bedienungsanleitung

SoundCraft

SoundCraft Si3 Bedienungsanleitung

SoundCraft

SoundCraft 200 Delta Bedienungsanleitung

Beliebte Musikmixer Handbücher anderer Marken

Neve

Neve 8816 Bedienungsanleitung

Mackie

Mackie Onyx Analogue Mixer Bedienungsanleitung

Behringer

Behringer EUROPOWER PMP518M Bedienungsanleitung

Peavey

Peavey S-32 Sanctuary Series Bedienungsanleitung

Rane

Rane MP 4 Bedienungsanleitung

True

True T9 Touchscreen Console Bedienungsanleitung

Studiomaster

Studiomaster Air Pro 24 Bedienungsanleitung

Pioneer

Pioneer SVM 1000 - Audio/Video Mixer Bedienungsanleitung

Roland

Roland M-160 Bedienungsanleitung

Yamaha

Yamaha MR1642 Bedienungsanleitung

Ecler

Ecler MAC40v Bedienungsanleitung

Pioneer

Pioneer DJM 909 - Battle Mixer W/Effects Bedienungsanleitung

Veeder-Root

Veeder-Root TLS-350 Series Bedienungsanleitung

Alto

Alto APM80.QUAD Bedienungsanleitung

Omnitronic

Omnitronic PM-211 Bedienungsanleitung

Roland

Roland SoundCanvas SC-8820 Bedienungsanleitung

CARVIN

CARVIN RX 1200 Bedienungsanleitung

Roland

Roland M-16E Bedienungsanleitung