SOYO SY-6VBA 133 Bedienungsanleitung

SY-6VBA 133

Motherboard

Quick Start Guide

CTested To Comply

With FCC Standards

FOR HOME OR OFFICE USE

POST CONSUMER

RECYCLED PAPER

100%

Hardware

Installation

Quick BIOS

Setup

Introduction

The SOYO CD

SOYO™

SY-6VBA 133 Motherboard

Pentium

III, Pentium

II & Celeron

processors

Via Apollo Pro133 AGP/PCI Motherboard

66/100/133 MHz Front Side Bus supported

ATX Form Factor

Trademarks:

Soyo is a registered trademark of Soyo Computer Inc. All trademarks are the property of their

owners.

Product Rights:

Product and corporate names mentioned in this publication are used for identification purposes

only and may be registered trademarks or copyrights of their respective companies.

transmit, transcribe, store in a retrieval system, or translate into any language, in any form or by

any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, any part of

this publication without express written permission of Soyo Computer Inc.

Disclaimer:

Soyo Computer Inc. makes no representations or warranties regarding the contents of this

manual. We reserve the right to revise the manual or make changes in the specifications of the

product described within it at any time without notice and without obligation to notify any person

of such revision or change. The information contained in this manual is provided for general use

by our customers. Our customers should be aware that the personal computer field is the subject

of many patents. Our customers should ensure that their use of our products does not infringe

upon any patents. It is the policy of Soyo Computer Inc. to respect the valid patent rights of third

parties and not to infringe upon or assist others to infringe upon such rights.

Restricted Rights Legend:

Use, duplication, or disclosure by the Government is subject to restrictions set forth in

subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at

252.277-7013.

About This Guide:

This Quick Start Guide is for assisting system manufacturers and end users in setting up and

installing the Motherboard. Information in this guide has been carefully checked for reliability;

however, no guarantee is given as to the correctness of the contents. The information in this

document is subject to change without notice.

If you need any further information, please visit our Web Site on the Internet. The address is

"http://www.soyo.com.tw".

6VBA 133 Serial - Version 1.2 - Edition: September 1999

*Thesespecificationsaresubjecttochangewithoutnotice

SY-6VBA 133

Quick Start Guide

Introduction

Congratulationsonyourpurchaseofthe

SY-6VBA133

Motherboard.ThisQuickStartGuide

describesthestepsforinstallingandsettingupyournewMotherboard.

ThisguideisdesignedforalluserstoprovidethebasicstepsofMotherboardsettingand

operation.Forfurtherinformation, pleasereferto SY-6VBA133MotherboardUser'sGuide

andTechnicalReferenceonlinemanualincludedontheCD-ROMpackedwithyour

Motherboard.

Unpacking

WhenunpackingtheMotherboard,checkforthefollowingitems:

TheSY-6VBA133ViaApolloPro133AGP/PCI

Motherboard

ThisQuickStartGuide

TheInstallation CD-ROM

SOYO3-in-1BonusPackCD-ROM(Norton AntiVirus,

GhostandVirtualDrive)

TheCPURetentionSet

OneIDEDeviceATA66FlatCable

OneFloppyDiskDriveFlatCable

SY-6VBA 133 Quick Start Guide

Introduction

SY-6VBA 133 Motherboard Layout

Key Features

SupportsIntelPentium

IIIprocessor(450-

600MHz), Pentium

IIprocessor(233-450MHz)&

Celeron

processor(266-433MHz

)

JumperlessandCPUvoltageAdjustable

SOYOCOMBOSetup

PC98,ACPI

ATA33/66

SupportsPC133memory

Power-onbymodemoralarm

SupportsWake-On-LAN(WOL)

Supportsonboardhardwaremonitoringand

includesHardware Doctor™utility

1x32-bitAGPslot

5x32-bitbusmasteringPCIslots

2xUSBportsonboard

1xIrDAport

Supportsmultiple-bootfunction

Y2KCompliant

SupportsPowerFailureResume

COM 1

COM 2

PRT

USB 1USB 2

PS/2 KB

Connector

PS/2 Mouse

Connector JP10

PCI Slot #1

PCI Slot #2

PCI Slot #3

PCI Slot #4

PCI Slot #5

ISA Slot #1

ISA Slot #2

JP9

JP8 LED1

Lithium

Battery

IR1

CPUFAN

ITE 8671

I/O Chipset

IDE 1

IDE 2

FDC

AGP Slot

ATX

Power

Flash BIOS

Slot 1

Via

82C596B

DIMM 1DIMM 1

DIMM 2

DIMM 3

DIMM 4

8 2 8 A C

Hardware

Monitoring

Winbond

W83782M

Via

82C693A

Speaker

Keylock

Power

LED

Turbo

LED

HDD

LED

Reset

PWRBT

CHAFAN

JP44

WOL

Header

JP7

JP5

JP2

Jumper

CMOS Clear

SY-6VBA 133

Quick Start Guide

Hardware

Installation

ToavoiddamagetoyourMotherboard,followthesesimpleruleswhilehandling

thisequipment:

BeforehandlingtheMotherboard,groundyourselfbygraspinganunpaintedportionof

thesystem'smetalchassis.

RemovetheMotherboardfromitsanti-staticpackaging.Holditbytheedgesand

avoidtouchingitscomponents.

ChecktheMotherboardfordamage.Ifanychipappearsloose,presscarefullytoseat

itfirmlyinitssocket.

Followthedirectionsinthissectiondesignedtoguideyouthroughaquickandcorrect

installationofyournew

SY-6VBA133

Motherboard.Fordetailedinformation,pleasereferto

SY-6VBA133MotherboardUser'sguideandTechnical Reference onlinemanualincluded

onthe CD-ROMpacked withyourMotherboard.

PREPARATIONS

Gatherandprepareallthenecessaryhardwareequipmenttocompletetheinstallation

successfully:

Slot1processorwithbuilt-inCPUcoolingfan(boxedtype)

SDRAMmodule

Computercaseandchassiswithadequatepowersupplyunit

Monitor

PS/2Keyboard

PointingDevice(PS/2mouse)

VGACard

SoundCard(optional)

Speaker(s)(optional)

DiskDrives:HDD,CD-ROM,Floppydrive…

ExternalPeripherals:Printer,Plotter,andModem-(optional)

InternalPeripherals:ModemandLANcards(optional)

SY-6VBA 133 Quick Start Guide

Hardware

Installation

Install the Motherboard

Followthestepsbelowinordertoperformtheinstallationofyournew

SY-6VBA133

Motherboard.

Step 1. Install the CPU

Mark your CPU Frequency:

RecordtheworkingfrequencyofyourCPU

thatshouldbeclearlymarkedontheCPUcover.

FSB66MHz

266MHz(66 x4.0) 333MHz (66 x5.0) 400MHz(66 x6.0)

300MHz(66 x4.5) 366MHz (66 x5.5) 433MHz(66 x6.5)

FSB100MHz

350MHz(100 x 3.5) 450MHz (100 x4.5) 550MHz (100 x5.5)

400MHz(100 x4.0) 500MHz (100 x5.0) 600MHz(100 x6.0)

FSB133MHz

400MHz(133 x3.0) 533MHz (133 x4.0) 666MHz(133 x5.0)

466MHz(133 x3.5) 600MHz (133 x4.5) 733MHz(133 x5.5)

CPU Mount Procedure:

Tomounttheprocessorthatyouhavepurchased

separately,followtheseinstructions.

Retention Module Step 1. Open the two sides by folding them up.

Step 2.

Push the locks on top of the CPU

inward. Step 3. Insert the CPU into the retention

module. The CPU fits in the CPU slot in

only ONE way, do not try to force it in.

Step 4. After completely

inserting the CPU,

push the two locks

on top of the CPU

outward. Now

your CPU is ready

for use.

To remove the CPU,

press the two notches

on top of the CPU

inward. Now press the

two slides on the

retention module down

and remove the CPU.

SY-6VBA 133

Quick Start Guide

Hardware

Installation

Note:Installing aheatsink andcooling fanontop ofyour CPU isnecessary forproper heat

dissipation.Failing to installtheseitems mayresultin overheating andpossibleburn-out of your

CPU.

Step 2. Make Connections to the Motherboard

ThissectiontellshowtoconnectinternalperipheralsandpowersupplytotheMotherboard.

InternalperipheralsincludeIDEdevices(HDD,CD-ROM),FloppyDiskDrive,ChassisFan,

FrontPanelDevices(TurboLED,InternalSpeaker,ResetButton,IDELED,and KeyLock

Switch.),Wake-On-LANcard,VGAcard,SoundCard,andotherdevices.

FormoredetailsonhowtoconnectinternalandexternalperipheralstoyournewSY-6VBA

133Motherboard,pleasereferto SY-6VBA133MotherboardUser'sGuideandTechnical

ReferenceonlinemanualonCD-ROM.

Connectors and Plug-ins

IrDA (Infrared Device Header): IR1 Wake-On-LAN Header: JP44

Pin1 Pin2 Pin3 Pin4 Pin5 Pin1 Pin2 Pin3

VCC None IRRX GND IRTX 5VSB GND MP-Wakeup

CPU Cooling Fan: CPUFAN Chassis Fan: CHAFAN

Pin1 Pin2 Pin3 Pin1 Pin2 Pin3

GND 12V SENSOR GND 12V SENSOR

Power LED Keylock

Pin1 Pin2 Pin3

Pin1 Pin2

5V NC GND

ControlPin GND

Speaker

Pin1 Pin2 Pin3 Pin4

5V NC NC Speakerout

HDD LED Turbo LED PWRBT RESET

Pin1 Pin2 Pin1 Pin2 Pin1 Pin2 Pin1 Pin2

LEDAnode LED

Cathode LED

Cathode GND Power

On/Off GND PowerGood GND

ATX Power On/Off: PWRBT ATX Power Supply: ATX PW

Connect your power switch to this

header (momentary switch type).

To turn off the system, please

press this switch and hold

down for longer than 4

seconds.

Attach the ATX Power cable to this connector. (This

motherboardrequiresanATXpowersupply,anATpower

supplycan NOTbe used.)

Note:Please make surethe ATX powersupply isableto

provideat least720mA ofcurrent onthe +5VSBlead ifyou

wantto enabletheadvanced powermanagement

functions,like powerfailureresume, Power-Onby

keyboard, etc.

Power LED

Key Lock

Speaker

Reset

PWRBT

Turbo LED

HDD LED

SY-6VBA 133 Quick Start Guide

Hardware

Installation

Step 3. Configure Memory

YourboardcomeswithfourDIMMsockets,providingsupportforupto1.5GBofmain

memoryusingunbufferedandregisteredDIMMmodulesfrom8MBto256/512MB.Onthis

motherboard,DRAMspeedcanbesetindependentfromtheCPUfrontsidebusspeed.

DependingontheDRAMclockspeedsettingintheBIOSsetup(Chapter3),appropriate

memorymodulesmustbeused.For66MHzDRAMspeed,usePC66memory;for100MHz

DRAMspeed,usePC100memory;for133MHzDRAMspeed,usePC133memory.

Memory Configuration Table

Number of

Memory Modules DIMM 1 DIMM 2 DIMM 3 DIMM 4

11st

22nd 1st

33rd 2nd 1st

44th 3rd 2nd 1st

RAM Type SDRAM

Memory Module

Size (MB) 8/16/32/64/128/256/512 MB

(For DIMM1& DIMM2) 8/16/32/64/128/256 MB

(For DIMM3 & DIMM4)

Note:Always install memory modules in the order prescribed in this table.

Step 4. CPU B21 and A14 Settings: JP8 and JP9

ForcertainIntelCPUs,themultiplierisnotlockedsuchthatsettingamultiplierhigherthan

specifiedontheCPUispossible.Fortechnicaldetailsreadthefollowing:

YourPII/III100/66MHzFSBCPUhasaninputpinB21(100/66#signal)totellitwhatFSB

frequencyitisrunningat;ThePIII133MHzFSBCPUhastwopinsB21andA14(133/100#

signal).JP8andJP9areconnectedtotheB21andA14inputrespectivelyandareusedto

tellCPUitsFSBspeed.

TheactualFSBFrequencyishoweversetthroughtheBIOSanditmaythereforedifferfrom

theFrequencyspecifiedtotheCPUthroughJP8&JP9.

BecausesomeINTELCPUshavetheirmultiplierslimitedataFSBFrequencyof100MHz

andhigher,tellingtheCPUthatitisrunningat66MHzthroughJP8&JP9whilesettinga

different(higher)FSBFrequencyintheBIOSmayallowtheusertosetahighermultiplier

value.DoingsowillhoweverforceyourCPUtooperateoutofits specifications,andtherefore

SOYOcannotguaranteetheproperfunctioningofyoursystem.

SY-6VBA 133

Quick Start Guide

Hardware

Installation

Refertothefollowingtable:

PII, Celeron PII,PIII PIII

JP9

133/100# JP8

100/66# tellCPU its

FSBSpeed 66MHzFSB 100MHzFSB 133MHzFSB

Short Short FSB=66MHz Normalsetting

Possiblehigher

multipliersetting

Short Open FSB=100MHz Normalsetting

Open Open FSB=133MHz Normal

setting

ThissettingwilltellCPUthatitisrunningon66MHz;thiswillreleasemoremultiplier

settingsonsomeIntelCPUs,butitwillmakethesystemoperateoutofits

specificationsiftheactualFSBfrequencyis100MHzhigher.

Step 5. FSB boot-up frequency and AGP divider: JP2 and JP7

ThesettingsofJP2andJP7determinetheFSBfrequencyatboot-up,andmoreimportant,

theydeterminetheAGPdividerandthegroupofFSBfrequenciesthatcanbeselectedinthe

BIOS.Refertothefollowingtable:

JP7 JP2 Boot-up

FSB BIOS FSB

group AGP divider

Short ShortPin1-2 66 66~83 1

Open Shortpin1-2 100 90~122 1.5

Open Shortpin2-3 133 124~155 2.0

Asexample,ifJP7issettoopenandJP2to(1-2),theboot-upFSBfrequencywillbe

100MHz.WhentheBIOStakescontrol,itwillwritetheBIOSFSBsettingtotheclock

generator.Thishappensshortlyafterpower-up,andtheFSBfrequencywillthenbein

accordancetotheBIOSsetting.ThegroupfromwhichtheFSBFrequencycanbeselected

intheBIOSis90~122MHzandAGPClockwillbe60~81MHz.NotethatallFSB

FrequenciesareavailableintheBIOS,butthatonlythoseinthegroupasdeterminedbyJP2

andJP7willhaveeffect whenselected.

SY-6VBA 133 Quick Start Guide

Hardware

Installation

Step 6. Set the CPU Frequency

YoudonotneedtosetanyjumperfortheCPUfrequency.Instead,CPUsettingsare

changedthroughtheBIOS

[SOYOCOMBO SETUP].

PleaserefertoChapter3-Quick

BIOSSetupfordetailsonhowtosettheSlot1processorfrequency.

Step 7. External Suspend Button (JP1)

Somecasescomewithasuspendbutton,inserttheplugintoJP1.Inadditiontothisbutton,

thesystemcanalsoenterthesuspendmodethroughyourOS.

Note:SuspendmodeonlyfunctionsifyourPowerManagementmodeisAPM.MakesurethattheBIOS

settingforPowerManagementisAPM.Windows98canbeinstalledwithACPIPower

Management(defaultisAPM),inthiscasesuspendmodewillnotfunctioneither.

Step 8. Enable/Disable Power-On by Keyboard (JP10)

YoucanchoosetoenablethePower-OnbyKeyboardfunctionbyshortingpin1-2onjumper

JP10,otherwise,shortpin2-3todisablethisfunction.

Power-On by

Keyboard Enable Disable

JP10 Setting Short pin 1-2 to

enable the

Power-On by

Keyboard function.

Short pin 2-3 to

disable the

Power-On by

Keyboard function.

Important: When using the Power-On by Keyboard function, please make sure the

ATX power supply can take at least 720mA load on the 5V Standby lead (5VSB) to

meet the standard ATX specification.

Step 9. 5V Stand-by indicator LED (LED 1)

ThisLEDislitwheneverthe5VStandbyvoltagecomingfromtheATX powersupplyis

available.Ifyou haveconnectedyourATX powersupplytothemains,LED1shouldbelit.

Andere Handbücher für SY-6VBA 133

Inhaltsverzeichnis

Andere SOYO Hauptplatine Handbücher

SOYO

SOYO SY-P4VTE Bedienungsanleitung

SOYO

SOYO SY-K7V DRAGON Plus Bedienungsanleitung

SOYO

SOYO SY-V6BE+ Bedienungsanleitung

SOYO

SOYO SY-5EH5/5EHM V1.2 Super 7 Bedienungsanleitung

SOYO

SOYO Super 7 SY-5SSM Gebrauchs- und Pflegehandbuch

SOYO

SOYO DRAGON Lite SY-KT333 Bedienungsanleitung

SOYO

SOYO SY-K7VTA-B Bedienungsanleitung

SOYO

SOYO SY-K7VMP2 Bedienungsanleitung

SOYO

SOYO SY-7VCM Bedienungsanleitung

SOYO

SOYO SY-6BE Bedienungsanleitung

SOYO

SOYO SY-7VBA 133 Bedienungsanleitung

SOYO

SOYO SY-P4X400 DRAGON Lite Bedienungsanleitung

SOYO

SOYO SY-D6IBA Gebrauchs- und Pflegehandbuch

SOYO

SOYO SY-6ZE+ Gebrauchs- und Pflegehandbuch

SOYO

SOYO SY-5EMA+ Gebrauchs- und Pflegehandbuch

SOYO

SOYO SY-7IWM/L V1.0 Bedienungsanleitung

SOYO

SOYO SY-P4I845PE Bedienungsanleitung

SOYO

SOYO Mainboard SY-5S Bedienungsanleitung

SOYO

SOYO 82430 HX Gebrauchs- und Pflegehandbuch

SOYO

SOYO SY-7IWB V1.0 Bedienungsanleitung

SOYO

SOYO SY-7SBB Bedienungsanleitung

SOYO

SOYO SY-6IZM/3 Bedienungsanleitung

SOYO

SOYO SY-7IWB Bedienungsanleitung

SOYO

SOYO SY-6BA+ Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung