Spacerails LEVEL 4 Bedienungsanleitung

LEVEL 4

PRODUCT AND CONSUMER WARNING

CHOKING HAZARD: This product contains small parts and is not intended for children under 3.

• This product is intended for users 8 years of age and older.

• To avoid choking, keep small parts away from children.

• Use caution—this product contains parts with sharp edges.

• To avoid potential damage to the product, only insert the included marbles into the elevator.

PARTS INCLUDED

Keep parts together to avoid misplacing them.

ARM COMPONENTS

Arm Clip

x56

Arm Sheath

x60

Arm Holder A

x56

Arm Holder B

x62

Arm Lock

x118

RAIL COMPONENTS

Rail Coupling

x10

Marble

Rail

26,000 mm

REQUIRED TOOLS & ITEMS (NOT INCLUDED)

Wire Cutters or Utility Scissors

Pen or Marker

3 AA Batteries (newer models) or 1 C Battery

Ruler (in centimeters)

Rail Clip

x70

SPLIT, SEE-SAW, AND START BLOCK COMPONENTSBASE COMPONENTS

Base Base Holder A Base Holder B

x9 x4 x6

Rail Splitter

Start Block

Cover

See-Saw Arm

ELEVATOR COMPONENTS

Elevator Helix

x12

Elevator Ring

Elevator Cover

Elevator Guard

Power Box Stand

Power Box

Shaft (300mm)

x16

Shaft (200mm)

Shaft Connector (90mm)

Shaft Connector (50mm)

ARM ASSEMBLY (QTY: 66 SHAFT TO RAIL)

RAIL SPLITTERS

1PREPARE THE COASTER COMPONENTS

Step 1: Attach one Arm Holder A and one

Arm Holder B with one Arm Sheath.

Step 2: Insert one Arm Clip into Arm

Holder A. Slide the circular part between

the matching parts on the Arm Holder.

Step 1: Attach one Rail Clip on each of

the Rail Splitter posts.

Step 4: Turn the Arm Lock

counter-clockwise to secure the

ArmClip in place.

Step 3: Insert Arm Lock through Arm

Holder A and Arm Clip. Ensure that the

tab is facing up.

To avoid damaging parts, do not move or adjust the Rail Clip while locked in the arm. To move the Rail Clip, release

Arm Lock by turning clockwise, position Rail Clip as desired, then secure Arm Lock again.

NOTE:

The hole shapes of the Arm Holder

and Arm Sheath dier.

Arm Holder B Arm Holder A

SEE-SAW ASSEMBLY

BASE ASSEMBLY

Step 1: Cut 2 rails to 55mm. Insert 1 rail into

each hole on the See-Saw.

Step 2: Insert the See-Saw Arm and the rails into

the Rail Clip. You may need to adjust the See-Saw

after installing it as it may have shifted.

Step 3: Insert See-Saw into Arm Holder B. Step 4: Insert the See-Saw into the Rail Stand

(300mm Shaft). See shaft assembly on page8

for exact placement.

See-Saw Arm

Rail Clip

55mm rail pieces

Step 1: Interlock Base block tabs

as shown below.

Step 2: Press Base Holder A and

Base Holder B pieces into the Base

blocks for a more secure hold.

NOTE:

Base Holder B is used

here instead of A.

Step 3: Once the Corkscrew is

built, attach three support shafts

(300mm) to the Power Box.

EELEVATOR ASSEMBLY

Step 2: Connect Elevator Helix

pieces together with the male part

facing up to ll the shaft.

NOTE:

Install the rst Elevator

Helix piece male side

up and rotate it until

it slides in place and

engages with driver at

the base of Power Box.

Step 1: Place a shaft in the

white hole on the Power Box.

Step 6: Place the Elevator Cover

onto the top of the elevator

assembly.

Step 7: Attach an Elevator Guard to

each of the Elevator Rings, then to

the right side of the Rail Clip.

Step 5: Place the three Elevator

Rings over the three shafts.

NOTE:

The Marble may fall

out of the elevator if it

enters too fast.

Step 4: Connect

one Rail Clip to each

Elevator Ring. Install

Elevator Ring with

tabs facing up, as

shown above.

STARTER ASSEMBLY

SHAFT ASSEMBLY

Step 1: Connect Arm Holder B to

300mm Shaft. Insert Arm Lock.

Step 4: Attach Rail Clips and

Start Block Cover to Starter.

Step 1: Slide Arm Holder B of each arm on

to a shaft and lock in place with Arm Lock.

Refer to the next page for orientation and

location of each arm.

This is how the pieces are

referenced on the shaft drawings.

Arm

Arm Holder B

See-Saw

Step 2: Connect the Starter pegs

to the Arm Holder.

Step 3: Ensure the Starter is at

a slight angle so the Marble will

run smoothly.

NOTE:

Please see the included full-size drawings for the next

several steps. This will simplify the positioning of base,

arms, shafts, and the rail cut lengths.

        

       

Step 2: Attach each Arm and See-Saw Arm as shown in step 1 with the orientation

and location shown here. In later steps the letter of each Shaft and number of each

Arm will guide in the installation of the Rails. Illustration is approximately 51% of

actual size. All Shaft measurements are in Millimeters.







200 200 200

104

124

140

117

300

225

300

149

103

247

300

102

264

300

276

300

256

300

113

278

Step 2 Continued

        

       

300 300 300 300 300300

110

67 72

79 80

111

123

119

107

135

162

199

115

161

168

216

201 203

240

208

226

216

258

241

277 283

281

200 200

109

141

185







HINSTALLING SHAFTS INTO BASE

Start Block

Shaft Stand

















 











LEFT

RIGHT

FRONTBACK

Step 3: Place shafts and elevator into base.

Push shaft into holes on base until sturdy.

Attach Power Box Stand to the Power Box.

Firmly seat the posts from the Power Box in

the holes on the base.

Step 4: Attach Shaft Connector (90mm) to

Shafts K and N. Attach Shaft Connector (50mm)

to Shafts F and G.

CUT THE RAIL TO SIZE

Step 1: Measure each section and mark the cutting point with a pen.

Step 2: Cut each section according to your measurement. Make sure

to cut at a 90° angle.

Tip: To help avoid do-overs and using too much rail, cut generously

(slightly longer than required) to begin with. You can always cut a

long rail shorter.

NOTES:

Illustration of rail lengths is

approximately 5% in scale.

Measure carefully and use a tape

measure for longer segments.

See included insert for rail

measurements in 1:1 scale.

300cm

5cm

45cm

200cm

350cm

Inhaltsverzeichnis

Andere Spacerails Spielzeug Handbücher

Spacerails

Spacerails Level 1 Bedienungsanleitung

Spacerails

Spacerails Level 8 Bedienungsanleitung

Spacerails

Spacerails LEVEL 6 Bedienungsanleitung

Spacerails

Spacerails Level 3 Bedienungsanleitung

Spacerails

Spacerails Level 9 Bedienungsanleitung

Spacerails

Spacerails Level 5 Bedienungsanleitung

Spacerails

Spacerails Level 2 Bedienungsanleitung

Spacerails

Spacerails Level 7 Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Handbuch

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

Meccano

Meccano 15103 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung