SPAL SHAVED-B Bedienungsanleitung

Installation Manual &

Operation Instructions

Shaved-B

Limited Warranty Statement

SPAL USA WARRANTY STATEMENT

SPAL USA warrants this product to be free from defects in material and workmanship for a

period of one (1) year from the date of sale to the original purchaser, and not more than two (2)

years from the date of manufacture. SPAL USA will repair this product free of charge if, in the

judgment of SPAL USA, it has been proven defective within the warranty period. The product

should be returned, at the customer expense, to the location of original purchase. This warranty

does not cover any expenses incurred in the removal and/or reinstallation of the product.This

warranty does not apply to any product damaged by improper installation, accidental misuse,

abuse, improper line voltage, fire, flood, lightning, or other acts of God, or a product altered or

repaired by anyone other than SPAL USA.This warranty is in lieu of other warranties, expressed

or implied, including any implied warranty of merchantability. No person is authorized to assume

for SPAL USA any other liability concerning the sale of this product.

IMPORTANT-KEEP YOUR INVOICE WITH THIS WARRANTY STATEMENT!

10/04

Trouble Shooting Reverse Polarity Wiring Problems

Switch doesn't work properly but the shaved kit transmitters do work

Step 1 Did you purchase a switch kit designed for three switches and only use two switches?

YES - Connect third switch

NO - Check wiring

Switch works properly but shaved kit transmitters do not work

Step 1 Does the LED on the remote light up when you press the transmitter button?

YES - Transmitter works properly continue to step 2

NO - Replace transmitter battery

Step 2 Can you hear the receiver make a clicking sound when you press channel 1 or 2 on

the transmitter?

YES - Receiver and relay work properly. Go to step 4

NO - Go to step 3

Step 3 Does the LED on the receiver light up when the transmitter button is pressed?

YES - Transmitter is properly learned and OK, go to Step 4

NO - Check power and ground to the receiver and then reprogram the transmitters

Step 4 Use a test light to check for voltage at pin 87 of the relay. Did the test show greater

than 10 volts?

YES - The relay checked works properly. The other side of the motor is not properly grounded.

NO - Connect pin 87 to a proper voltage source.

SPAL USA, 512 Tuttle Street, Des Moines, IA 50309-4618

[email protected], www.spal-usa.com

Main/Sales: 800-345-0327, Sales: 888-SPAL-USA

Tech Support Line: 800-454-7725

Each Kit Contains The Following Components

Output From Receiver 87A

86 85

+ 12 VDC

FUSE

87A

Output From Receiver

Power Window

Motor

BATER

Output From Receiver 87A

+ 12 VDC Output

+ 12 VDC

FUSE

Optional Wiring Diagrams

Positive Output

Negative Output

Reverse Polarity Output

BATY

Output From Receiver

Ground Output

87A

GROUND

FUSE

+ 12 VDC

FOR POWER WINDOWS TWO RELAYS MUST BE PLACED BETWEEN THE SWITCH AND THE

WINDOW MOTOR. THE DASHED LINES INDICATE WHERE THE WIRES MUST BE CUT.

(1) Receiver (2) Remotes

(2) Wire Harnesses

Installation Instructions for SPAL Shaved Door Handle Kit

Shaved-40

This kit is designed to operate up to seven functions via the four-button remote control.

Channels 1 and 2 are Positive outputs used to open your drivers and passenger doors. Channels 3

through 7 are all negative outputs tht can be used ot operate power door locks, power door releases, truck

releases, control linear actuators, or roll power windows up or down, with an additional (external) relay.

(See Page 7)

**Proper wiring is critical to the correct operation of this product. Inspect all wiring to be certain of proper

connections, a quality ground, and appropriate fusing. Also check wire rounting, keeping wires away from

potential damage such as moving parts**

2 7

• The solenoids provided in the SHAVED40 kit can be mounted horizontally or

vertically (with the plunger UP) to the door with the provided hardware.

• Attach the solenoid to the door latch with the supplied cable and cable crimp.

-Loop the cable through the solenoid and the door latch and crimp the two ends

together with the cable crimp.

Solenoid Wiring:

• Attach the white wire of the Driver Door Solenoid to the Brown wire (large

gauge/channel 1, from spade connector harness) of the receiver.

• Attach the white wire of the Passenger Door Solenoid to the Yellow wire (large

gauge/channel 2, from spade connector harness) of the receiver

• Connect the remaining black wire of the solenoid to a ground located on the

vehicle body. (The door is not a proper grounding source!)

**A mechanical backup switch should be utilized in the case of power failure. (See the

optional wiring section)**

Mounting/WiringSection

Receiver Mounting and Wiring:

**The receiver must be mounted inside the vehicle to avoid moisture**

***Do not plug in the receiver module until all the wiring is complete!***

***Do Not Ground the Antenna!***

ANTENNA

NOT USED

+12 VOLTS DC

CH1 OUTPUT (+)

CH2 OUTPUT (+)

SEE TABLE

DIP SWITCHES

PROGRAMMING BUTTON

LED

JUMPERS

MOLEX CONNECTOR

SPADE CONNECTORS

Notes:

*Connecting the YELLOW (ignition) wire will disable Channels 1-4 while the ignition key is ON.

**Whan installing a SHAVED ACT Kit replace the 35 Amp fuse with the supplied 10 Amp fuse

The unit will stop operating for 30 seconds if any combination of the Remote Control

Buttons 1 and/or 2 are pressed eight (8) times in 30 seconds. After 30 seconds the unit

will automatically reset to standard operating mode.

Mounting/WiringSection

Molex Connector Spade Connectors

Pin # Wire Color Circuit Wire Color Circuit

1 Black Ground Violet Not Used

2 Not Used Not Used Orange Not Used

3 Purple Channel 7 Red Positive 12 VDC**

4Blue Channel 5 Brown Channel 1

5Orange Channel 3Yellow Channel 2

6 Red Positive 12 VDC

7Yellow Ignition*

8 Not Used Not Used

9 White/Black Channel 6

10 Brown Channel 4

Brown or Yellow

Wire of Receiver

Black: Connect

to ground

CABLE CRIMPS

1.25" MAXIMUM

EXTENSION

DOOR LATCH

MECHANISM ARM

Reprogramming the Remote Transmitters:

**This Shaved Door kit can accept up to 4 SPAL remote transmitters (Part #MULTI-RCU7TX)**

The remote transmitters are shipped Pre-Programmed. In the event that a remote

transmitter loses the programmed code, or if you wish to add more remote

transmitters, follow these instructions:

• Make sure ignition is OFF.

• Locate the programming button located on the side of the receiver, next to the LED.

• Press the programming button 3 times quickly (The LED will light).

• Press Button (1) on each transmitter you want learned in to the receiver (one at a time).

There is a 10 second window to learn all new transmitters.

• The LED will remain lit for approximately 10 seconds after the last remote transmitter has

been recognized.

• Wait for the LED to go out. Then test each remote transmitter for proper function.

Jumper Settings:

To avoid damage to attached components,

the jumpers must remain in the factory setting.

To Operate: Press:

Channel 1 Button 1

Channel 2 Button 2

Channel 3 Button 3

Channel 4 Button 4

Channel 5 Button 1 + Button 2

Channel 6 Button 1 + Button 3

Channel 7 Button 1 + Button 4

Basic Function of the SPAL Shaved Door Kit

The remote control supplied with your kit has four buttons, but is capable of controlling

7 channels.

Channel 1: +12VDC Opens drivers door

Channel 2: +12VDC Opens passenger door

Channel 3:

Channel 4:

Channel 5:

Channel 6:

Channel 7:

Operation Section

Programming Section

Basic Functions Of The Remote Control

Emergency/Backup Switch (not included in kit):

It is strongly recommended that an emergency/backup switch be mounted outside the

vehicle in the case of lost transmitters or keys locked in the vehicle.

BATER

DO NOT GROUND INSIDE THE DOOR

Optional Wiring Section

Item to be Description Relay Type # of Relays Diagram

Activated of Function Required

1 Power window motor Move window up & down SPDT 2 Reverse

1 Power window motor Move window one direction SPDT 1 Reverse

Linear actuator Move in & out SPDT 2 Reverse

Solenoid Activate Solenoid SPST 1 Positive or Negative

Trunk Release Open the Trunk SPST 1 Positive or Negative

Door lock actuator Lock & unlock SPDT 2 Reverse

SPST = Single pole single throw relay, 30 or 40 amp

SPDT = Single pole double throw relay 30 or 40 amp

Relays can either be purchased from SPAL USA or from your local auto parts store.

If The Control Unit Is Connected To:

Dip Settings*

Solenoids 1-2: Off 3-7: Off

Actuators 1-2: On 3-7: Off

Optional Mechanical Backup Cable (HR-Entry)

DIP SWITCHES

A mechanical backup cable

should be utilized in all shaved

door applications.

By using a mechanical

backup, you do not run the risk

of being locked out of the vehicle

if the battery were to go dead.

SPAL USA offers a universal

mechanical cable

(part #HR-ENTRY) that can be run

to a concealed location, such as

the front wheel well.

Dip Switch Settings:

Wiring Options

Power Wire Ground Wire

Drivers Door Grey wire of Control Unit Chassis Ground

Passenger Door Green wire of Control Unit Chassis Ground

Inside Button Option:

Internal Buttons: If you wish to remove the door handles from inside the vehicle and

use power buttons, you will need to wire the buttons as follows:

Optional negative outputs (250 mA)

**Additional relays are required for each channel**

(See Page 7 For Wiring Diagrams)

* Switches 3-8 will always be in the OFF position

**12 Gauge

Wire Must

Be Used**

Dieses Handbuch passt für folgende Modelle

Andere SPAL Autoalarmanlage Handbücher

SPAL

SPAL AS 80 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8717 Kurzanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung