Speco 960H Series Bedienungsanleitung

Installation and

Operation Manual

SPECO 960H series

ooo

oooo

eee

HINTMD1H

2User Information

Explanation of two Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

"dangerous voltage" within the product's

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance-(servicing) instructions in the

THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE

ON THE BOTTOM OF THE SYSTEM.

"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THE UNIT TO RAIN OR MOISTURE"

enclosure that may be of sufficient magnitude to constitute a

risk of electric shock to persons.

literature accompanying the appliance.

CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

User Information

Regulatory Notice 3

Regulatory Notice

This equipment has been tested and found to comply with

limits for a Class A digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment

is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the

user will be required to correct the interference at their own

expense.

Changes or modifications not expressly approved

by the manufacturer could void the user's authority

to operate the equipment.

WARNING

When this camera is installed near equipment,

like a wireless communication device that emits

a strong electromagnetic field, some irregularity

such as noise on the monitor screen may happen.

CAUTION

• This installation should be made by a qualified service person

and should abide to all local codes.

Contents

1. 6

2. Features 7

3.1.

Composition

Parts

6.1.

6.2.

6.3.

6.3.1.

6.3.2.

6.3.3.

6.3.4.

6.3.5.

6.3.6.

6.4.

6.4.1.

6.4.2.

6.4.3.

6.5.

6.5.1.

6.5.2.

6.5.3.

6.5.4.

6.5.5.

6.6.

6.6.1.

6.6.1.1.

6.6.1.2.

Operating Camera

Camera OSD menu

PRESET

EXPOSURE

LENS

(DC or ESC)

BRIGHTNESS

– Adjusts brightness of the image.

SHUTTER

– Adjusts the shutter speed.

FLK

(FLICKERLESS)

AGC

(Auto Gain Control)

INTENSIFY

WHITE BAL.

– White Balance Setup

ATW

PUSH

MANUAL

DAY / NIGHT

AUTO

DAY

– For color mode only.

NIGHT

– For BLACK and WHITE mode only.

EXTERN

IRED

BACKLIGHT

BLC

(back-light compensation)

, HLC

(high-light compensation)

OFF

– Disable

BLC

– To lighten a darker part of the image.

4.1.

4.1.1.

4.2.

Installation

Connection

Make the connections

Camera mounting

5.1.

5.1.1.

5.1.2.

Name and Functions

Camera controls

Menu navigation

Monitoring and switches

Contents

Important Safety Instructions

Contents 5

7.1

Troubleshooting

Resolving problems

8.1

8.2

Technical Data

Specifications

– HINTMD1H

Dimensions

6.6.1.3.

6.6.2.

6.6.2.1.

6.6.2.2.

6.6.2.3.

6.7.

6.8.

6.8.1.

6.8.2.

6.8.3.

6.8.4.

6.8.5.

6.8.6.

6.8.7.

6.8.7.1.

6.8.7.2.

6.8.8.

6.8.8.1.

6.8.8.2.

6.9.

6.9.1.

6.9.1.1.

6.9.1.2.

6.9.1.3.

6.9.2.

6.9.3.

6.9.4.

6.9.5.

6.9.6.

6.9.7.

6.9.8.

6.10.

6.10.1.

6.10.2.

HLC

– Force blocking the bright part.

D-WDR

(Digital Wide Dynamic Range)

, DEFOG

OFF

– Disable

D-WDR

DEFOG

SPECO DNR

– Digital Noise Reduction

IMAGE

SHARPNESS

– To adjust SHARPNESS of the image.

CHROMA

– To adjust the color intensity of the image.

MONITOR

SHADING

H-MIRROR

– Horizontal image flip

POSI/ NEGA

– Invert the colors of the images

MOTION

– Motion detect

OFF

– Disable

PRIVACY

OFF

– Disable

SYSTEM

OSD

– On Screen Display

CAM TITLE

ID DISPLAY

FONT COLOR

CAM ID

– CAMERA ID (RS-485 Communication ID)

SYNC

BAUDRATE

COAXIAL

DEFECT

(Pixel defect compensation)

LANGUAGE

VERSION

– Camera Software History ..

EXIT

SAVE

PRESET

– In the state of the EXIT, press menu button exit.

Important Safety Instructions

1. Important Safety Instructions

10.

11.

12.

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Clean only with a dry cloth.

Do not block any ventilation openings. Install in accordance

with the manufacturer's instructions.

Do not install unit near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

Only use attachments/accessories specified by the

manufacturer.

Unplug this apparatus during lightning storms or when

unused for long periods of time.

Refer all servicing to service personnel. Servicing is required

when the apparatus has been damaged in any way, such

as power supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

Do not install the camera in extreme temperature conditions.

Operate the camera under conditions where temperatures

are within -10°C(14°F) to +50°C(122°F). Especially be careful

for ventilation under high temperature.

Features 7

2. Features

Min Illumination (F1.2, 30IRE, ICR B/W)

Works under extreme low illumination conditions:

– INTENSIFIER [X32] : Color 0.005 Lux

Variety of convenience functions

Provides special functions for advanced manipulation of

your device, including:

– Adjustable sharpness enhancement [700 TV Lines]

– Adjustable privacy mask [8 masks]

– Adjustable motion detection [4 areas]

– SPECO DNR [Digital Noise Reduction]

– INTENSIFIER [X32]

– BLC [Backlight Compensation]

– POSI / NEGA

– MIRROR [Horizontal]

– Coaxial communication [Pelco-C]

D-WDR (Digital Wide Dynamic Range)

Greatly improves image quality and detail even in backlight

conditions, by increasing exposure in dark areas while

decreasing it in bright areas, resulting in a corrected image

with clear details in both bright and dark areas.

1/3 inch High Sensitivity CCD

Composition

3. Composition

3. 1. Parts

The camera unit consists of the following parts:

• CAUTION: Installation should only be performed by

qualified service personnel in accordance with the

National Electrical Code or applicable local codes.

No.

Plastic anchors

Dome base

Mounting screws

Dome cover

L-wrench for dome cover mounting

Parts

Installation 9

4. Installation

4. 1. Connection

Connecting to Power and Video

4.1.1. Make the connections

• The wire is non-polarized.

• Use 24V AC power source or 12V DC power source.

4. 2. Camera mounting

– Use cables and conduits that are suitable for the installation.

– Particular attention should be paid in the installation so that no

moisture is allowed to penetrate into the unit through the cables

or conduits during the life time of the product.

– Products of which the internal parts are exposed to moisture

because improper installation are not covered by warranty.

No.

Video Output

Power Input

Function

Terminal Color

Remarks

Yellow

Red

1.0 Vp-p

24V AC (±20%) / 12V DC (±10%)

12V DC

24V AC

AC AC

Remove the top cover.

Fix the base on the wall or ceiling.

Put the dome cover over the base.

Fix the dome cover on the base with the L-wrench.

Adjust the rotational position of the camera for desired viewing of the side.

Video Output

GND

360°

Horizontal

360°

Pan

Tilt

90°

Name and Functions

DOWN

RIGHT

LEFT

5. Name and Functions

5. 1. Camera controls

• NOTE: Push the Joy stick for one second, and the OSD

appears on the screen. Move the Joy Stick up, down, left

& right to control the OSD functions.

5.1.1. Menu navigation

No.

Down

Left

Right

Menu(Center)

Parts

Move the cursor up in the screen.

Move the cursor down in the screen.

Move the cursor left in the screen.

Move the cursor right in the screen.

Press straight down to open menu or set.

Remarks

5.1.2. Monitoring and switches

No.

Service

monitor

connector

Parts

When installing the camera, connect a

service monitor to set angle of view and

focus of the screen.

(This output cannot be used simultaneously

with the main video output.)

Remarks

DOWN

RIGHT

LEFT

Dieses Handbuch passt für folgende Modelle

Andere Speco Sicherheitskamera Handbücher

Speco

Speco Intense-IR Series Bedienungsanleitung

Speco

Speco HT-7816DNV Bedienungsanleitung

Speco

Speco HT-7048IRVF Bedienungsanleitung

Speco

Speco VL647iLT Bedienungsanleitung

Speco

Speco CVC-61HRB Bedienungsanleitung

Speco

Speco CVC-190 Bedienungsanleitung

Speco

Speco HT-7246IHR Bedienungsanleitung

Speco

Speco CVC-105CM Bedienungsanleitung

Speco

Speco O8VB2 Bedienungsanleitung

Speco

Speco Intensifier K Glacier Series Bedienungsanleitung

Speco

Speco O8FD1 Bedienungsanleitung

Speco

Speco VL644H Bedienungsanleitung

Speco

Speco VL-10 Bedienungsanleitung

Speco

Speco O2VT1 Bedienungsanleitung

Speco

Speco OIPC21T7B Bedienungsanleitung

Speco

Speco O2P30X Bedienungsanleitung

Speco

Speco HT-7247IHR Bedienungsanleitung

Speco

Speco O2iBD4 Bedienungsanleitung

Speco

Speco HTSD37X Bedienungsanleitung

Speco

Speco CVC-644DC Bedienungsanleitung

Speco

Speco O4iT1 Bedienungsanleitung

Speco

Speco O4FT2 Bedienungsanleitung

Speco

Speco WDR705H Bedienungsanleitung

Speco

Speco HT-7715DNV Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung