Speco VLD9 Bedienungsanleitung

USER MANUAL

Thank you for purchasing our product. Speco Technologies is constantly developing and

improving products. We reserve the right to modify product design and specifications

without notice and without incurring any obligation.

VLD9 /VLD9M

Warnings

■ If the product does not work properly, please contact the dealer or where the product was purchased.

Speco Technologies is not responsible for any problems caused by improper operation or repair.

■ Do not expose the unit to heavy stress, violent vibration or long-term exposure to water and humidity

during transportation, storage, and/or installation.

■ Do not install near sources of heat.

■ Only install the product in environments inside the specification operating temperature and humidity

range.

■ Do not install the camera near power lines, radar equipment or other electromagnetic radiation.

■ Do not block any ventilation openings if any.

■ Use all the weatherproofing hardware requirement to minimize weather intrusion.

This camera series is the latest technology and advanced circuit design, which features high definition and

sensitivity, low noise and distortion and supports HD video transmission with the common coaxial cable,

ensuring the requirement of the HD monitoring in the traditional surveillance system.

Introduction

● High Resolution

Adopt high performance sensor, providing high definition and clear image.

● High Transmission Performance

Real-time transmission with high speed and long distance.

● DNR

Reduce noise from brightness and color signal.

● OSD

Access the camera settings which can be clearly displayed through the main menu.

● White Balance

Adjust the color temperature according to the environment automatically.

● AGC

Adjust the gain of amplifier, enabling the camera to output the standard video signal in different

lighting condition.

● Backlight Compensation (BLC)

When the back of the captured object is too much bright, you can set BLC for the captured object to

make it clearer.

● Backlight Compensation (BLC)

When the back of the captured object is too much bright, you can set BLC for the captured object to

make it clearer.

Cables

Power Cable

Video Output

Video Switch Cable

Video Switch: Four video output modes can be optional--AHD, TVI, CVI and CVBS

(a) remove the cover of the video switch cable; (b) hold and press the button in the video

switch cable for 5 seconds to switch the current video output.

Before you start, please make sure that the wall or ceiling is strong enough to wi ths tand three times

the weight of the camera. Please install and use the camera in the dry environment.

You’d better install back the lens cover or lower dome less than 4 hours after removing it.

The mounting types of cameras are only for reference.

Installation

►Mounting for VLD9

1. Drill the screw holes and the cable hole on the wall according to the drill template.

74.3

(mm)

2. Align the gap of the trim ring with the microphone by turning the trim ring with fingers. Then remove

the trim ring from the gap of the camera.

Rubber plug

Lower dome

* Install it when routing the

cables through the ceiling.

3. Loosen the screws to open the lower dome. Then route and connect the cables.

4. Secure the camera to the wall with screws provided as shown below.

5. Three-axis adjustment. Before adjustment, preview the image of the camera on a monitor and then

adjust the camera according to the figure below to get an optimum angle.

Rotation 0°~355°

Pan 0°~355°

Tilt 0°~67°

6. Install the lower dome back to the camera and fix it with screws. Then put the trim ring onto the lower

dome and then rotate it clockwise until it is locked. Finally, remove the protection film softly.

Trim ring



Gap

Microphone

∅4.6

90.2mm

►Mounting for VLD9M

1. Drill the screw holes and the cable hole on the wall according to the drill template.

2. Align the gap of the trim ring with the microphone by turning the trim ring with fingers. Then remove

the trim ring from the gap of the camera.

Rubber plug

Lower dome

* Install it when routing the

cables through the ceiling.

3. Loosen the screws to open the lower dome. Then route and connect the cables.

4. Secure the camera to the wall with screws provided as shown below.

Gap

Trim Ring

Microphone

6. Install the lower dome back to the camera and fix it with screws. Then put the trim ring onto the lower

dome and then rotate it clockwise until it is locked. Finally, remove the protection film softly.

Turn

Rotation 0°~345°

Tilt 0°~77°

Pan 0°~345°

5. Three-axis adjustment. Before adjustment, preview the image of the camera on a monitor and then

adjust the camera according to the figure below to get an optimum angle.

Specifications

Camera

Image Sensor

Resolution

Image size

Video Output

Image System

Electronic Shutter

IR Range (feet)

Frame Rate

Min. Illumination

Lens

Lens Mount

S/N Ratio

Ingress Protection

Functions

Function Control

Day & Night

WDR

Digital NR

AGC

Auto White Balance

HLC

BLC

LSC

Mirror

Privacy Mask

Smart IR

Sharpness

Image Setting

Defect Correction

Others

Power Supply

1/2.8" CMOS

2MP

1920×1080

AHD/TVI/CVI/CVBS (*camera comes defaulted to HD-TVI)

PAL/NTSC

33~66 65~98

30fps(60Hz); 25fps(50Hz)

0.001lux @F1.2, AGC ON; 0 lux with IR

2.8 mm 2.8~12 mm，motorized

M12 D14

≥ 52dB(AGC OFF)

IP 67 & IK10

OSD (UTC control)

ICR

120dB

Yes

Auto

DC12V (± 10%)

IR OFF: < 1W; IR OFF: < 1W;

Specifications

Models VLD9

Power Consumption

Dimensions (inch)

Working Environment

IR ON : < 4W IR ON : < 6W

-22 °F ~ 122 °F, 10 % ~ 90 %(relative humidity)

Ф5.61 3.95×

Ф4.72 3.45×

VLD9M

Model: VLD9 /VLD9M

Federal Communications Commission (FCC) Statements

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause

undesired operation.

FCC Responsible Party:

Speco Technologies

200 New Highway

Amityville, NY 11701

www.specotech.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Speco Sicherheitskamera Handbücher

Speco

Speco VLEDB2HW Bedienungsanleitung

Speco

Speco PROVIDEO CVC-620WP Bedienungsanleitung

Speco

Speco O4P4 Bedienungsanleitung

Speco

Speco CDD11HW Bedienungsanleitung

Speco

Speco HLPR67T Bedienungsanleitung

Speco

Speco O2iB6 Bedienungsanleitung

Speco

Speco O2VLB8 Bedienungsanleitung

Speco

Speco CVC5845DNV Bedienungsanleitung

Speco

Speco O4VT1NG Bedienungsanleitung

Speco

Speco Intensifier O2iD8M Bedienungsanleitung

Speco

Speco CVC-5815DNV Bedienungsanleitung

Speco

Speco HTD8FFI Bedienungsanleitung

Speco

Speco VL-62 Bedienungsanleitung

Speco

Speco H5T1M Bedienungsanleitung

Speco

Speco H4FB1 Bedienungsanleitung

Speco

Speco VL-64TP Bedienungsanleitung

Speco

Speco CVC-225ES Bedienungsanleitung

Speco

Speco VL-265PIR Bedienungsanleitung

Speco

Speco O2iD5M Bedienungsanleitung

Speco

Speco Deterrent O4TDD1M Bedienungsanleitung

Speco

Speco O8T8M Bedienungsanleitung

Speco

Speco HTINTT5H Bedienungsanleitung

Speco

Speco DD2 Datenblatt

Speco

Speco O4iB2M Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung