Spectra Precison GL412N Installationsanleitung
GL412N/GL422N Controls
Battery Status LED
Level-LED
Manual Mode/Escape/
Standby Button
Power Button
HI-/Manual-
Standby - LED
Slope/Alignment
Buttons
Menu button Enter button
Enter buttonMenu button
GL412N/GL422N Peripherals
Rubber Feet
Serial Number
5/8” x 11
Beam Exit
Metal Sunshade Sighting Guides
GL412N/GL422N Peripherals
Plastic Feet
Rubber Foot Laser Safety Labels
5/8” x 11
Installing The Batteries
Enter the battery housing, by
turning the battery-door knob
counterclockwise
Install/remove the rechargeable
battery Pack. It is keyed to
prevent miss-insertion. The cage
prevents accidental charging of
Alkaline batteries
Do not try to open the cage for
exchanging the rechargeable
batteries
Worldwide charger has plugs for
US, EU, AU and GB
Recharge time is about 10 hours
Installing The Batteries
If using 4 x D-cell Alkaline's, note the
plus (+) and minus(-) diagram on the
battery door. Do NOT try to install
Alkaline batteries in the rechargeable
battery Pack!
Special screws are used to ensure only
autorized service centers can replace the
batteries. Trying to open the cage will
destroy the cage lid holders.
New warning label
at the battery cage
RC402N Radio Remote Control
Left & Right
Buttons
Menu button
Up & Down Buttons
LCD - Display
On/Off Button
RC402N-Battery status LED
Enter button
Hand loop
Manual Mode/Escape/
Standby Button
RC402N Radio Remote Control
Powering the RC402N
1. Open the battery door using a coin
or similar pry device to release the
battery door tab on the RC402N.
2. Insert two AA batteries noting the
plus (+) and minus (-) diagrams
inside the battery housing.
3. Close the battery door. Push down
until it “clicks” into the locked
position.
Turning On/Off the Radio Remote Control
Press the button to turn on the radio remote control.
The remote control mirrors the functionality of the
GL412N/GL422N keypad.
To turn off the radio remote control, press and hold
the button for 2 seconds.
Pairing the remote control with the transmitter
First, make sure the transmitter and the
remote control are turned off. Then press
and hold the button and turn on the
transmitter.
–The laser’s battery LED flashes fast.
During the next 6 seconds repeat the
same steps on the remote control.
The Laser’s red battery LED flashes fast,
then the laser and RC402N display show
Pairing OK for one second and then the
same function as the laser is actually
working to indicate the transmitter has
been matched with the remote control.
Make sure the transmitter is turned off.
First, turn on the receiver, then press and hold the (A) and (B) buttons for two
seconds. After two seconds, the display shows MENU first,
then RDIO. Press and release the button –
display shows the current radio mode.
If not already set to LS, press (C) button (current mode flashes)
then press (A) or button (B) until Mode LS is displayed.
Press (C) button again to enter selection.
Press and release the (B) button – display shows PAIR.
Press the (C) button again – the display shows PAIR and a rotating bar.
Then press and hold the button and turn on the transmitter
(Battery LED flashes fast). After completing, PAIR/OK will be displayed.
The laser pairs now automatically with the new receiver and turns back to the standard
function.
Press and release the HL760 button two times to exit the menu at the receiver.
A laser symbol and an antenna is lit to confirm the receiver is ready for communication
with the laser.
or or
A
B
C
Pairing the HL760 receiver with the transmitter
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Spectra Precison Messgerät Handbücher
