Sper scientific 860043 Bedienungsanleitung
1
Free and Total
Chlorine Meter
860043
Instruction Manual
BLANK PAGE
3
Table of Contents
1. Features ...................................................... 4
2. Specications ............................................... 5
3. Front Panel Description ................................ 7
4. Mode Selection ............................................. 8
4. Calibration Procedure.................................... 8
5. Measuring Procedure .................................. 10
Measurement............................................... 10
Data Hold .................................................... 11
Data Record ................................................ 11
6. Battery Replacement................................... 12
7. Warranty ...................................................... 12
4
Features:
The meter measures Free and Total Chlorine between 0.00 to 3.50
ppm ( mg/L ).
The measuring method is an adaptation of the USEPA Method
330.5 for waste water and Standard Method 4500-Cl G for drinking
water.
The advanced optical system is based on a special narrow band
LED lamp that allows most accurate and repeatable reading.
User friendly and powerful calibration functions are able to validate
the performance of your meter at any time.
1.00 ppm Free standard solution and 1.00 ppm Total standard
solution are included as standard accessories.
The unique optics structure enables the instrument to read with
high resolution : 0.01 ppm ( mg/L ).
Splash waterproof on the front panel.
Jumbo LCD, easy readout.
Microprocessor circuit assures maximum possible accuracy,
providing special functions and features.
Battery operated for eld and on-site testing convenience.
Data hold function for freezing the desired value on display.
Records Maximum and Minimum reading with Recall.
Heavy duty & compact housing with hard carrying case, designed
for easy carry out & operation.
Auto shut o feature to save battery life.
Applications: Test swimming pool, municipal water, food and
beverage water, or other aqueous solution where uid clarity is
important.
5
Specications:
Display LCD size : 41 mm x 34 mm
Range Free chlorine ( CL ) :
0.00 to 3.50 ppm ( mg/L ).
Total chlorine ( CL ) :
0.00 to 3.50 ppm ( mg/L ).
Resolution 0.01 ppm ( mg/L ).
Accuracy ± 0.02 ppm ( mg/L ).
@ 1.00 ppm ( mg/L ).
Light source LED, 525 nm.
Light detector Photo diode.
Method The measuring method is an adaptation
of the USEPA Method 330.5 and Standard
Method 4500-Cl G.
Note: The reaction between free ( total )
chlorine and the DPD reagent cause a pink
tint in the sample.
Response time Less than 10 seconds.
Sample volume 10 mL.
Data Hold Freeze the display reading.
Memory Recall Maximum & Minimum value.
Display Sampling
Time
Approx. 1 second.
Power o Auto shut o saves battery life or manual
o by push button.
Calibration points Zero chlorine.
1.00 ppm ( Free chlorine ).
1.00 ppm ( Total chlorine ).
Operating
Temperature
0 to 50 °C.
Operating
Humidity
Less than 85% R.H.
Power Supply DC 1.5 V battery ( UM4, AAA ) x 6 PCs,
or equivalent.
6
Power Current Stand by Approx. DC 4 mA.
Testing Approx. DC 12 mA.
Weight 320 g/0.70 LB. Battery is included.
Dimension 155 x 76 x 62 mm
( 6.1 x 3.0 x 2.4 inch)
Accessories
Included
• Instruction manual ..………………….1 PC
• 1.0 ppm Free Chlorine standard
solution, (LUTU-CF)..…………………..1 PC
• 1.0 ppm Total Chlorine standard
solution, (LUTU-CT)……………..….….1 PC
• Zero Chlorine standard solution,
(LUTU-CL)...………………………....….1 PC
• Empty testing bottle…………….....2 PCs
• Clean
cloth………………………………...1 PC
• Free Chlorine DPD powder……..10 PCs
• Total Chlorine DPD powder……..10 PCs
Optional
Accessories
• Free Chlorine DPD powder
(LUCFP-10)
• Total Chlorine DPD powder
(LUCTP-10)
• Empty testing bottle (LUTU-CELL)
• 1.0 ppm Free Chlorine standard solution,
(LUTU-CF)
• 1.0 ppm Total Chlorine standard solution,
(LUTU-CT)
• Zero Chlorine standard solution,
(LUTU-CL)
7
Front Panel Description:
4
3. FRONT PANEL DESCRIPTION
3-1 Test Chamber Cover
3-2 Test Chamber
3-3 Display
3-4 Hold Button ( Esc Button )
3-5 TEST/CAL Button
3-6 Power Button
3-7 ZERO Button
3-8 REC Button ( MAX, MIN Button )
3-9 Battery Compartment/Cover
3-10 Free Chlorine 1.0 ppm standard solution.
3-11 Total Chlorine 1.0 ppm standard solution
3-12 Zero Chlorine standard solution
3-13 Empty testing bottle 1
3-14 Empty testing bottle 2
3-15 Clean Cloth
3-16 Free Chlorine DPD powder ( 10 PCs )
3-17 Total Chlorine DPD powder ( 10 PCs )
4
3-1 - Test Chamber Cover
3-2 - Test Chamber
3-3 - Display
3-4 - Hold Button
3-5 - TEST/CAL Button
3-6 - Power Button
3-7 - ZERO Button
3-8 - REC/MAX/MIN Button
3-9 - Battery Compartment
3-10 - Free Chlorine 1.0 ppm standard
3-11 - Total Chlorine 1.0 ppm standard
3-12 - Zero Chlorine standard
3-13 - Empty testing bottle 1
3-14 - Empty testing bottle 2
3-15 - Cleaning Cloth
3-16 - Free Chlorine DPD power (10pcs)
3-17 - Total Chlorine DPD power (10pcs)
8
Mode Selection:
Follow these steps to switch between Free and Total Chlorine
testing modes.
1) With the meter o, press and hold the HOLD button and the
REC/MAX/MIN button. While continuing to hold the HOLD and the
REC/MAX/MIN button, press the Power button. The unit will enter
the selection mode and display the current mode selected.
2) Press the TEST/CAL button to switch between Free and Total
modes.
3) Press the REC/MAX/MIN button to conrm and save the mode
into memory.
Note:
- For swimming pool applications, the Free Chlorine function is typi-
cally used.
- For industrial water applications, the Total Chlorine function is
typically used.
Calibration Procedure:
1) The meter can be calibrated under the following calibration
points:
Free Chlorine
- Zero ppm
- 1.00 ppm
Total Chlorine
- Zero ppm
- 1.00 ppm
Note: The calibration procedures for the “Total Chlorine” and the
“Free Chlorine” are independent of each other.
2) Calibration requires the following two solutions.
- Zero Chlorine standard
- 1.0 ppm standard (Free or Total)
9
Calibration Procedure (continued):
3) Follow the steps below to perform calibration of the zero and
1.0ppm standards
1) Open the test chamber, place the zero chlorine
standard in the chamber and close the chamber lid.
Note: Be sure the testing bottle is seated
fully and oriented correctly. The white mark
on the bottle should point towards the white
mark on the test chamber.
2) Turn on the meter. The meter will display
the current mode (Free or Total) briey then
will display CAL 0.
3) Press the Zero button. The meter will show CAL 0.00,
then start ashing TEST. Once complete, the meter will
display 0.00 ppm. (Note: this step is not part of the
calibration process, this step sets the zero point for the
meter at power up)
4) Press and hold the TEST/CAL button until CAL is
displayed on the display then release the button. Press the
TEST/CAL button again to enter the calibration function.
5) 0.00 PPM and CAL will be displayed. With the zero
chlorine standard in the chamber, press the TEST/CAL
button and CAL will begin to ash on the screen. Once
complete, 1.00 ppm and CAL will be displayed.
6) Replace the zero chlorine standard in the teat chamber
with the 1.00 ppm chlorine standard. Then press the
TEST/CAL button. CAL will begin to ash on the screen.
Once complete, the unit will display 1.00 ppm.
7) Calibration is now complete and the meter is ready
to use. (Note: It is recommended to perform the calibration
at least once per day/use)
10
Measuring Procedure:
Note: Be sure to selected the appropriated measurement mode
before performing a measurement. Refer to the Mode Selection.
1) Fill the testing bottle to the 10ML line with test sample.
2) Open the test chamber and place the test sample in the chamber
and close the chamber lid.
Note: Be sure the testing bottle is seated fully and oriented cor-
rectly. The white mark on the bottle should point towards the white
mark on the test chamber.
3) Turn on the meter. The meter will display the current mode (Free
or Total) briey then will display CAL 0.
4) Press the Zero button. The meter will show CAL 0.00, then start
ashing TEST. Once complete, the meter will display 0.00 ppm.
(Note: this step is not part of the calibration process, this step sets
the zero point for the sample at power up)
5) Open the test chamber and remove the testing bottle. Open the
test bottle and add the Free or Total DPD powder. Close the test
bottle and shake bottle for at least 10 seconds.
6) Wait approximately one minute, then insert the test bottle back in
to the test chamber and close the lid.
7) Press the TEST/CAL button, the display will ash TEST. Once
complete, the display will show the measurement value.
Note: After testing, you should wash the testing bottle with distiled
water.
Inhaltsverzeichnis
Andere Sper scientific Messgerät Handbücher
Sper scientific
Sper scientific 801038 Bedienungsanleitung
Sper scientific
Sper scientific 840087 Bedienungsanleitung
Sper scientific
Sper scientific 840021 Bedienungsanleitung
Sper scientific
Sper scientific DS-2013SD Bedienungsanleitung
Sper scientific
Sper scientific 860055 Bedienungsanleitung
Sper scientific
Sper scientific 300100 Bedienungsanleitung
Sper scientific
Sper scientific 850023 Bedienungsanleitung
Sper scientific
Sper scientific 850026 Bedienungsanleitung
Sper scientific
Sper scientific 840005 Bedienungsanleitung
Sper scientific
Sper scientific 840060 Bedienungsanleitung
Sper scientific
Sper scientific 840020 Bedienungsanleitung
Sper scientific
Sper scientific 800058 Bedienungsanleitung
Sper scientific
Sper scientific 850068 Bedienungsanleitung
Sper scientific
Sper scientific 850070 Bedienungsanleitung
Sper scientific
Sper scientific 840081 Bedienungsanleitung
Sper scientific
Sper scientific 900030 Bedienungsanleitung
Sper scientific
Sper scientific 800015 Bedienungsanleitung
Sper scientific
Sper scientific 800046 Bedienungsanleitung
Sper scientific
Sper scientific 300068 Bedienungsanleitung
Sper scientific
Sper scientific 850024 Bedienungsanleitung
