Spirit XT685 Bedienungsanleitung

OWNER’S MANUAL

Please carefully read this entire manual before operating your new treadmill

TABLE OF CONTENTS

Important Safety Instructions 2

Important Electrical Instructions 3

Grounding Instructions 3

Important Operation Instructions 4

Assembly Instructions 5

Transport Instructions 11

Features 12

Console Operation 14

Programmable Features 17

Using Heart Rate Transmitter 26

General Maintenance 28

Exploded View Diagram/Parts List 33

ATTENTION

This treadmill is intended for residential use only and is warranted for this application.

Any other application voids this warranty in its entirety.

XT810-AT38CEGS_1102A

IMPORTANT SAFETY INSTRUCTIONS

WARNING - Read all instructions before using this appliance.

DANGER - To reduce the risk of electric shock disconnect your treadmill from the electrical

outlet prior to cleaning and/or service work.

WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons, install

the treadmill on a flat level surface with access to a 230-volt, 10-amp grounded outlet with

only the treadmill plugged into the circuit.

DO NOT USE AN EXTENSION CORD UNLESS IT IS A 14AWG OR BETTER, WITH

ONLY ONE OUTLET ON THE END.

The treadmill should be the only appliance in the circuit in which it is connected.

DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY USING IMPROPER

ADAPTERS, OR IN ANY WAY MODIFY THE CORD SET. A serious shock or fire hazard

may result along with computer malfunctions. See Grounding Instructions, page 3.



Do not operate treadmill on deeply padded, plush or shag carpet. Damage to both carpet

and treadmill may result.



Do not block the rear of the treadmill. Provide a minimum of 3 1/2 feet clearance

between the rear of the treadmill and any fixed object.



Keep children away from the treadmill. There are obvious pinch points and other caution

areas that can cause harm.



Keep hands away from all moving parts.



Never operate the treadmill if it has a damaged cord or plug. If the treadmill is not

working properly, call your dealer.



Keep the cord away from heated surfaces.



Do not operate where aerosol spray products are being used or where oxygen is being

administered. Sparks from the motor may ignite a highly gaseous environment.



Never drop or insert any object into any openings.



Do not use outdoors.



To disconnect, turn all controls to the off position, then remove the plug from the outlet.



Do not attempt to use your treadmill for any purpose other than for the purpose it is

intended.



The hand pulse sensors are not medical devices. Their purpose is to provide you

with an approximate measurement in relation to your target heart rate. Use of a chest

transmitter strap is a much more accurate method of heart rate analysis. Various factors,

including the user’s movement, may affect the accuracy of heart rate readings. The

pulse sensors are intended only as exercise aids in determining heart rate trends in

general.



Use handrails provided; they are for your safety.



Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for

use on your treadmill. Quality athletic shoes are recommended to avoid leg fatigue.

SAVE THESE INSTRUCTIONS - THINK SAFETY!

IMPORTANT ELECTRICAL INSTRUCTIONS

WARNING!

NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. As with any appliance with a

large motor, the GFCI will trip often. Route the power cord away from any moving part of the treadmill

including the elevation mechanism and transport wheels.

NEVERremove any cover without first disconnecting AC power. If voltage varies by ten percent (10%)

or more, the performance of your treadmill may be affected. Such conditions are not covered under your

warranty. If you suspect the voltage is low, contact your local power company or a licensed electrician for

proper testing.

NEVER expose this treadmill to rain or moisture. This product is NOT designed for use outdoors, near a

pool or spa, or in any other high humidity environment. The operating temperature specification is 40 to

120 degrees Fahrenheit, and humidity is 95% non-condensing (no water drops forming on surfaces).

Circuit Breakers: Some circuit breakers used in homes are not rated for high inrush currents that can

occur when a treadmill is first turned on or even during use. If your treadmill is tripping the house circuit

breaker (even though it is the proper current rating) but the circuit breaker on the treadmill itself does not

trip, you will need to replace the home breaker with a high inrush type. This is not a warranty defect.

This is a condition we as a manufacture have no ability to control. This part is available through most

electrical supply stores. Examples: Grainger part # 1D237, or available online at www.squared.com

part # QO120HM.

GROUNDING INSTRUCTIONS

This product must be grounded. If the treadmill should malfunction or breakdown, grounding provides a path

of least resistance for electric current, reducing the risk of electric shock. This product is equipped with a cord

having an equipment-grounding plug. The plug must be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes and ordinances.

DANGER - Improperconnectionoftheequipment-groundingconductorcanresultinariskofelectric shock.

Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly

grounded. Do not modify the plug provided with the product if it will not fit the outlet; have a proper outlet

installedbyaqualifiedelectrician.

This product is for use on a nominal 230-volt circuit, and has a grounding plug that looks like the plug

illustrated below. A temporary adapter that looks like the adapter illustrated below may be used to

connect this plug to a 2-pole receptacle as shown below if a properly grounded outlet is not available. The

temporary adapter should be used only until a properly grounded outlet, (shown below) can be installed

by a qualified electrician. The green colored rigid ear-lug, or the like, extending from the adapter, must be

connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is

used, it must be held in place by a metal screw.

IMPORTANT OPERATION INSTRUCTIONS



NEVER operate this treadmill without reading and completely understanding the

results of any operational change you request from the computer.



Understand that changes in speed and incline do not occur immediately. Set your

desired work level on the computer console and release the adjustment key. The

computer will obey the command gradually.



NEVER use your treadmill during an electrical storm. Surges may occur in your

household power supply that could damage treadmill components. Unplug the

treadmill during an electrical storm as a precaution.



Use caution while participating in other activities while walking on your treadmill;

such as watching television, reading, etc. These distractions may cause you to lose

balance which may result in serious injury.



Do not use excessive pressure on console control keys. They are precision set to

function properly with little finger pressure.

SAFETY TETHER CORD



A safety tether cord is provided with this unit. It is a simple magnetic design that

should be used at all times. It is for your safety should you fall or move too far back on

the tread-belt. Pulling this safety tether cord will stop tread-belt movement.

To Use:

1. Place the magnet into position on the round metal portion of the console control head.

Your treadmill will not start and operate without this. Removing the magnet also

secures the treadmill from unauthorized use.

2. Fasten the plastic clip onto your clothing securely to assure good holding power. Note:

The magnet has strong enough power to minimize accidental, unexpected stopping.

The clip should be attached securely to make certain it does not come off. Be familiar

with its function and limitations. The treadmill will stop, depending on speed, with a

one to two step coast anytime the magnet is pulled off the console. Use the Stop /

Pause switch in normal operation.

ASSEMBLY INSTRUCTIONS

!!ATTENTION: IMPORTANT UNPACKING INSTRUCTIONS. PLEASE READ

BEFORE UNPACKING YOUR FOLDING TREADMILL!!

Serious injury could occur if this folding treadmill is not unpacked properly.

There is a Velcro strap installed around the treadmill base that prevents the treadmill

from unfolding accidentally during shipping. If this strap is not removed properly the

treadmill could spring open unexpectedly and cause injury if someone is standing near

the treadmill when the strap is removed.

To ensure your personal safety during removal of the shipping strap please make sure

the treadmill is positioned flat on the ground, in the orientation it would be in if you were

using the treadmill. Do not turn the treadmill up on its side while removing the shipping

strap. This could cause the treadmill’s folding mechanism to spring open. If the end of

the Velcro strap (that you need to grab to remove it) happens to be under the treadmill

deck, reach under the deck to grab it, but do not tilt the treadmill up to gain access to

the strap end.

Cut the banding straps with a short box cutter (razor knife); separate the carton from the

one underneath it by prying up on the staples (if applicable). Pull the carton over the

treadmill parts and locate the hardware pack. The hardware pack is separated into five

sections; one section containing tools and four sections labeled steps 1-4 which contain

the hardware needed for assembly of each step. The assembly steps below are

numbered one through four and correspond to the hardware in the numbered sections

of the hardware pack. Remove only the hardware for the step you are currently

assembling to avoid confusion and mix ups.

Then remove the treadmill from the carton and lay it on a level surface.

ASSEMBLY TOOLS

Combination M5 Allen Wrench

& Phillips Head Screw Driver

#109. Phillips Head Screw Driver

#18. Deck/Belt Lubricant

#106. M6 Allen Wrench #63. Safety Key

UPRIGHT TUBE ASSEMBLY

1. Slide the bottom console covers onto the console mast tubes (52 onto5Left side &53 onto4

Right side). Make sure they are oriented as shown in the illustration.

2. Connect computer cables (32 &33) on the right side.

3. Insert console mast tubes (4&5) into the frame.Caution: Be careful not to pinch the cables you

just connected. Doing so could affect the console function.Pull the end of the cable tight as

you insert the right console mast tube.

4. Insert three Button Head Socket Bolts (102) and one Button Head Socket Bolt (103) and Split

Washer (108) on each side. Partially tighten these using the M6 Allen Wrench (106). Don’t

completely tighten these until the end of step 3.

HARDWARE

102

. 5/16” x 15mm

Button Head Socket

Bolt (6 pcs)

108

3/8” x 2T

Split Washer

(2 pcs)

103

. 3/8” x 2”

Button Head Socket

Bolt (2 pcs)

CONSOLE ASSEMBLY

1. Connect the following cables together: Incline cables35 to39, Speed cables34 to38, and

Computer cables33 to31.

2. Place the console (37) onto the brackets at the top of the console mast tubes and attach with two

Button Head Bolts (104) and two Split Washers (108) on each side. Caution: Be careful not to

pinch any of the cables. Doing so may affect the console function. Firmly tighten with the

Combination M5 Allen Wrench & Phillips Head Screw Driver (107).

HARDWARE

108

. 3/8” x 2.0T

Split Washer (4 pcs)

104

. 3/8” x 1

3/4”

Button Head Socket

Bolt (4 pcs)

BASE COVERS

1. Attach the bottom console covers (52 &53) to the console with five Sheet Metal Screws (105)

on each side. Tighten with the Phillips Head Screw Driver (109) or Combination M5 Allen

Wrench & Phillips Head Screw Driver (107).

2. Attach the cross brace (3) to the console mast tubes (4&5) with two Button Head Socket Bolts

(102) on each side. Tighten with the M6 Allen Wrench (106).

3. Firmly tighten the eight Button Head Socket Bolts inserted in Step 1 with the M6 Allen Wrench

(106). Place the accessory holder tray (48) securely on top of the cross brace (3).

HARDWARE

102

. 5/16” x 15mm

Button Head Socket

Bolt (4 pcs)

105

. 3.5 x 12mm

Sheet Metal Screw

(10 pcs)

Andere Handbücher für XT685

Inhaltsverzeichnis

Andere Spirit Tretmühle Handbücher

Spirit

Spirit XT185 Bedienungsanleitung

Spirit

Spirit XT685 Bedienungsanleitung

Spirit

Spirit XT385 Bedienungsanleitung

Spirit

Spirit CT850 Bedienungsanleitung

Spirit

Spirit XT385 Bedienungsanleitung

Spirit

Spirit XT285 Bedienungsanleitung

Spirit

Spirit inspire IN300T Bedienungsanleitung

Spirit

Spirit XT485ENT Bedienungsanleitung

Spirit

Spirit CT800ENT Bedienungsanleitung

Spirit

Spirit Esprit T10 Bedienungsanleitung

Spirit

Spirit Z100-A81 Bedienungsanleitung

Spirit

Spirit 16007603850 Bedienungsanleitung

Spirit

Spirit XT285 Bedienungsanleitung

Spirit

Spirit CT850 ENT Bedienungsanleitung

Spirit

Spirit XT385 Bedienungsanleitung

Spirit

Spirit XT385 Bedienungsanleitung

Spirit

Spirit Z700-A82 Bedienungsanleitung

Spirit

Spirit Esprit CT80 Bedienungsanleitung

Spirit

Spirit XT10 Bedienungsanleitung

Spirit

Spirit CT850 ENT Bedienungsanleitung

Spirit

Spirit XT685 Bedienungsanleitung

Spirit

Spirit XT285 Bedienungsanleitung

Spirit

Spirit XT485 Bedienungsanleitung

Spirit

Spirit Esprit CT90 Bedienungsanleitung

Beliebte Tretmühle Handbücher anderer Marken

Treadly

Treadly TREADLY 2 Bedienungsanleitung

HEALTH ONE

HEALTH ONE Walk Ro Bedienungsanleitung

NordicTrack

NordicTrack NTL12941 Bedienungsanleitung

NordicTrack

NordicTrack T7.5 S Bedienungsanleitung

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 Bedienungsanleitung

Merax

Merax MS282992 Bedienungsanleitung

FYTTER

FYTTER RU-2SX Bedienungsanleitung

Precor

Precor 903 Bedienungsanleitung

FitLogic

FitLogic freewill d225 Bedienungsanleitung

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB Bedienungsanleitung

Horizon Fitness

Horizon Fitness Adventure 5 Plus Bedienungsanleitung

Stamia

Stamia InMotion II Bedienungsanleitung

Smooth Fitness

Smooth Fitness EVO 3i Bedienungsanleitung

NordicTrack

NordicTrack NETL81810.0 Bedienungsanleitung

Schwinn

Schwinn 830/Journey 8.0 Bedienungsanleitung

Keys Fitness

Keys Fitness HealthTrainer HT-740T Bedienungsanleitung

NordicTrack

NordicTrack T 14.0 Treadmill Bedienungsanleitung

Master

Master F22 Bedienungsanleitung