SportsPlay HERCULES CLIMBER VII Bedienungsanleitung

February 17, 2010

902-300 HERCULES CLIMBER VII

INSTALLATION INSTRUCTION

INSTALLATION DETAILS

Recommended crew (Adult):2

Installation time: 8 hrs (16 man hrs over two days)

User age: 2-12 yrs

Use zone: 72” from the furthest point of structure

Weight: 800

SURFACING: Use of safety surfacing in compliance with

ASTM specification F1292 is required.

MAINTENANCE:

As the owner of the playground you are responsible for

maintenance of the equipment and play area. A

maintenance schedule must be developed and the

equipment inspected frequently. A maintenance section

that includes component specific maintenance

requirements is included at the end of this manual.

Be sure to inspect surfacing for foreign objects that could

cause injury and that sufficient surfacing is in place in

accordance with ASTM and CPSC standards.

February 17, 2010

902-300 HERCULES CLIMBER VII

INSTALLATION INSTRUCTION

PARTS LIST

PART #

DESCRIPTION

QTY

905-302

Net for Hercules Climber

905-303

Angle Net For Hercules Climber

905-261

T 27 Torx Bit

416-350

3/16” Socket Key

PART #

DESCRIPTION

QTY

913-108

5” O.D x 11’4” Post

913-398

3.5” O.D.x6’2” Post

315-996

Red Bottom End Cap 5” Post

913-397

Top Support for Angle Net

913-396

Horizontal Support for Angle Net

913-395

Vertical Support for Angle Net

913-307

Rope Bracket for Hercules

Climber

903-302

Arch Ladder for Hercules

Climber

903-301

Plastic Panel for Hercules

Climber

905-208

Gasket for Attachment Bracket

905-526

Self Tapping Screws

112

913-417

Panel Attachment Bracket

913-402

Four Hole Attachment Bracket

196-807

3/8”x3/8” Set Screw

316-501

5/16” Flat Washers

316-601

3/8” Flat Washer

226-602

3/8” Hex Nut

905-847

Red Bolt Caps

216-512

5/16”x1” Button Head Nut

116-529

5/16”x ¾” Button Head Bolt

NOTE: Keep a copy of these instructions on file to assist you

with maintenance and replacement parts.

February 17, 2010

902-300 HERCULES CLIMBER VII

INSTALLATION INSTRUCTION

FOOTING INFORMATION

Total footing depth is 23” less the height of the surfacing

plus the height of the blocking material. If you are using

12” of surfacing the footing hole would need to be 11” plus

the height of the blocking material (refer to both the side

and front cutaway views to the right).

If the Play structure is installed on a unlevel grade you must

adjust the footing depth to accommodate the grade. For

instance, if the grade for this component is 1” higher than

the surface grade of the main playground post you must dig

your footing hole 1” deeper.

You must place the bottom of the support post or slide leg

on a suitable flat blocking material to prevent it from

sinking further into the soil. We recommend you use a

brick, block of wood or several inches of gravel. The

footing depth does not include this blocking material since

materials used often vary.

It is the owner/installers responsibility to check local

building codes and to comply with those codes. All footing

depths listed here are recommendations and local soil types

and frost lines may require a deeper and/or wider footing

depth. If that’s the case you must add more blocking

material to accommodate the deeper footing, as the post

length will still only be installed at the depth listed in this

instruction manual.

Assemble the entire unit before adding the concrete unless

instructed to do so in the individual component instruction

sections.

February 17, 2010

902-300 HERCULES CLIMBER VII

INSTALLATION INSTRUCTION

February 17, 2010

902-300 HERCULES CLIMBER VII

INSTALLATION INSTRUCTION

SPECIFICATIONS

Panel- ¾” UV protected HDPE

Hardware – Stainless steel & tamper resistant

Attachment Brackets- Electrostatically applied & oven

cured powder coat

Paint – Electrostatically applied & oven cured powder coat

Tube – FloCoat® Galvanized 1 3/8” OD and 1” OD.

Nets-16mm Steel Reinforced Rope

INSTALLATION TIPS & TROUBLE SHOOTING

SportsPlay Equipment Inc. recommends pre-drilling the

holes in the post when attaching a four-hole bracket with a

number #7 drill bit. This will make the attachment of the

four-hole bracket with the self-tapping screws easier and it

will prevent damage to the screw head during installation.

Apply locktite to all bolts during assembly prior to

completely tightening them.

Stainless Steel hardware can occasionally be difficult to use

particularly if you need to take them out to make an

adjustment. It is recommended that you add a drop of oil to

bolts that may have to be removed before you install them.

Do not tighten bolts all the way until the unit is completely

assembled and all components are square and level.

Identify and separate all parts by referencing the detail

drawings and the parts list.

As you unpack and separate the components, use the

cardboard sheets that were used for packing and shipping to

prevent damage to the components. This is particularly true

all Powder Coated and Thermoplastic coated components,

by setting the components on top of the cardboard.

February 17, 2010

902-300 HERCULES CLIMBER VII

INSTALLATION INSTRUCTION

BEFORE YOU BEGIN

In addition to the components on the packing list you will need a

post hole digger, level, tape measure, drill, 9/16” wrench, hack saw,

blocking material, marking paint, and cement.

INSTALLATION STEPS

__1) Review all instructions before beginning

__2) Unpack, organize, and identify all components: Be sure to

place all painted components on a protective surface (cardboard,

cloth, etc…) to prevent damage.

__3 Dig footing holes: Refer to the footing drawing in your

instruction booklet.

__4) Place posts in proper location: Install the Red Posts Caps (3)

into the bottom of the 5” Post before placing it in the footing hole.

The three 5” Posts (1) will set in the middle footing holes. The 3

½” Posts (2) will set in the two footing holes on one end of the

structure.

__ 5) Attach the Horizontal Support for Angle Net: The

Horizontal Support for the Angle Net (5) attaches between one of

the 3 ½” Posts (2) and the 5” Post (1) make sure that the first ½”

hole in the Horizontal Support for the Angle Net is 19 ½” from the

5” Post. The Horizontal Support for the Angle Net will need to be

set 6” above the depth of the surfacing. Attach this to the post with

the Self Tapping Screws making sure that an Attachment Bracket

Gasket is in between the Horizontal Support for the Angle Net and

the Post. Repeat this step for the other Horizontal Support for the

Angle Net connecting it to the opposite 3 ½” post and the same 5”

post, making sure the supports are level. (See detail A)

February 17, 2010

902-300 HERCULES CLIMBER VII

INSTALLATION INSTRUCTION

INSTALLATION STEPS CONTINUED

__6) Install Vertical Support for Angle Net: Both Vertical

Supports for the Angle Net (6) will install to the 5” Post that the

Horizontal Support for the Angle Net attached to. The first Vertical

Support for Angle Net will install directly above one of the

Horizontal Supports, it will need to be 15” center to center of the

Attachment points. Install it with the Self Tapping Screws making

sure that the Gasket for the Attachment Bracket is between the

Vertical Support and the Post. Repeat this for the other Vertical

Support. (See detail A)

__7) Install the Top Support for the Angle Net: The top support

for the Angle net is mounted above the Vertical support, it is 80”

from center to center of the Horizontal Support and Top Support.

Attach this with the Self Tapping Screws making sure that the

Attachment Bracket Gasket is between the Top Support and the

Post. (See detail A)

__8) Install the Angle Net: The Angle Nets install with the bolts

that are attached to the nets, one Flat 3/8” Washer (16), one 3/8”

Hex Nut (17) and one Red Bolt Cap bottom (18). One of the end

bolts of the Angle Net will bolt through the 3 ½” post, secure it by

placing the red bolt cap bottom onto the bolt against the post. Then

place a 3/8” Flat Washer onto the bolt and seat it into the Red Bolt

Cap, place a Hex Nut onto the bolt leaving ½” to 1” of threads

showing on the opposite side of the post. The other end bolt will

connect through the Top Support in the same fashion. Repeat these

steps until all bolts of both Angle Nets are attached. Do not tighten

until cement has cured. (See detail B)

February 17, 2010

902-300 HERCULES CLIMBER VII

INSTALLATION INSTRUCTION

INSTALLATION STEPS CONTINUED

__9) Block and level: You will need to block the two 3 ½” posts

and the one 5” post that you have installed the Angle Net to. After

the three posts are secure and level you can pour cement or a “HOT

MIX” into the footing holes. Check the post for level throughout

the rest of the construction of the structure.

__10) Install Panel Attachment Brackets: To complete this step

you will need the Plastic Panel (9), eight Panel Attachment

Brackets (12), eight Gaskets for Attachment Brackets (10), and 32

Self tapping Screws (11). First you will need to layout the

placement of the Panel Attachment Brackets. The bottom of the

panel should be level with the height of the surfacing. The first

Panel Attachment Bracket should be approximately 2” above the

bottom of the Plastic Panel, install a Panel Attachment Bracket in

this location. You will then need to figure the total height of the

panel and place a second Panel Attachment Bracket 2” lower than

the total height of the Plastic Panel. Evenly space the remaining

two Panel Attachment Brackets between the top and bottom

brackets. Repeat this for the other post that the Plastic Panel will

attach to. (See detail E)

February 17, 2010

902-300 HERCULES CLIMBER VII

INSTALLATION INSTRUCTION

INSTALLATION STEPS CONTINUED

__11) Attach the plastic Panel: You will need eight each of the

5/16”x1” Button Head Nuts (19), 5/16” x ¾” Button Head Bolts

(20), 5/16” Flat Washers (15), and 3/8” Flat Washers (16). Place

one 3/8” Flat Washer on each of the 5/16” x 1” Button Head Nuts

and insert it into the plastic panel then through the corresponding

Panel Attachment Bracket. Secure it with a 5/16” x ¾” Button

Head bolt and a 5/16 Flat Washer. Repeat this for the remaining

attachment brackets. (See detail A)

__12) Install the Rope Bracket for the Hercules Climber: The

bottom of the attachment point of the Rope Bracket will install at

the same height as the top of the surfacing you are installing it on.

Use the Self Tapping Screws (11) and the Gasket for the

Attachment Bracket (10) to connect to the Posts. (See detail A)

__13) Install the Rope Climber: This will install in the same

manner as the Angle Rope Climbers did. Do not tighten until the

cement has set. (See detail B)

__14) Connect the Arch Ladders: These will connect to the 5”

Post between the Rope Climber and the Plastic Panel. Place one of

the four 4 hole Brackets (13) on each of the small ends of the Arch

Ladders (8). Next you will need to place the larger of the ends of

the Arch Ladders into the footing holes. Carefully lean the Arch

Ladder over to the 5” Post and secure it with the Self Tapping

Screws and an Attachment Bracket Gasket between the post and

Bracket. Repeat this for the other Arch Ladder. (See detail D)

_15) Once the entire playground has been installed and you have

verified that the entire playground is level you can add the

concrete to the footing holes. Be sure to use concrete with a

minimum 2,500 psi and mix the concrete per the manufacturer’s

directions before you pour it into the footing hole. Once the

footing has been filled with concrete you should rope of the area for

a minimum of 48 hours to allow the concrete set properly.

__16) Once the concrete has set, use locktite when tighten the

bolts that are attached to the rope climbers, once they are tight you

will need to cut off the extra bolts and install the Red Bolt Cap

tops. Now you can back fill dirt over the footing holes; inspect the

area and components for tools, hazardous debris and sharp edges.

Verify all components are installed and all hardware is tight and

then install the safety surfacing.

__17) Inspect the components: for sharp edges and if necessary

file them down and apply touch up paint.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere SportsPlay Spielgeräte und Spielplatzausstattung Handbücher

SportsPlay

SportsPlay 511-111 Bedienungsanleitung

SportsPlay

SportsPlay Quick Ship 3 Modified Bedienungsanleitung

SportsPlay

SportsPlay 581-438H Bedienungsanleitung

SportsPlay

SportsPlay 581-830H Bedienungsanleitung

SportsPlay

SportsPlay 801-312-H Bedienungsanleitung

SportsPlay

SportsPlay 581-438F Bedienungsanleitung

SportsPlay

SportsPlay 581-238F Bedienungsanleitung

SportsPlay

SportsPlay 581-830-8F Bedienungsanleitung

SportsPlay

SportsPlay 581-638F Bedienungsanleitung

SportsPlay

SportsPlay Mega Series Bedienungsanleitung

SportsPlay

SportsPlay 902-290 Bedienungsanleitung

SportsPlay

SportsPlay Seth Mega Installations- und Betriebshandbuch

SportsPlay

SportsPlay QUICK SHIP 1 MODIFIED Bedienungsanleitung

SportsPlay

SportsPlay 601-695S Bedienungsanleitung

SportsPlay

SportsPlay 581-630-8M Bedienungsanleitung

SportsPlay

SportsPlay 382-404H Bedienungsanleitung

SportsPlay

SportsPlay 581-238M Bedienungsanleitung

SportsPlay

SportsPlay 581-630M Bedienungsanleitung

SportsPlay

SportsPlay HERCULES CLIMBER VI Bedienungsanleitung

SportsPlay

SportsPlay SUPER SLIDE Bedienungsanleitung

SportsPlay

SportsPlay 581-240HD Bedienungsanleitung

SportsPlay

SportsPlay 581-643H Bedienungsanleitung

SportsPlay

SportsPlay 581-242F Bedienungsanleitung

SportsPlay

SportsPlay 511-109 Bedienungsanleitung

Beliebte Spielgeräte und Spielplatzausstattung Handbücher anderer Marken

FUNormous

FUNormous Disney Junior MICKEY MOUSE Bedienungsanleitung

b4Adventure

b4Adventure Slackers TREEZONE ADVENTURE THREE HOUSE Bedienungsanleitung

PoolMaster

PoolMaster 72775 Bedienungsanleitung

Palmako

Palmako 4743142009857 Installationshandbuch

BOERPLAY

BOERPLAY PSTE000.019 Bedienungsanleitung

MGA Entertainment

MGA Entertainment Little Tikes Dunk'n Toss Bouncer Benutzerhandbuch

stilum

stilum Erika Bedienungsanleitung

Costway

Costway NP10816 Bedienungsanleitung

Trigano

Trigano VABI Bedienungsanleitung

Outward

Outward OUT116 Bedienungsanleitung

GALOPIN

GALOPIN ARC02 Bedienungsanleitung

stilum

stilum levis Technische Daten

Ledon

Ledon BASIC Bai LB012 Bedienungsanleitung

BOERPLAY

BOERPLAY PSTE115.002 Bedienungsanleitung

Europlay

Europlay S306 Programmierhandbuch

SportsPlay Equipment

SportsPlay Equipment 361-509H Bedienungsanleitung

Ledon

Ledon 302250 Bedienungsanleitung

Costway

Costway NP10441 Bedienungsanleitung