SportsPlay 902-290 Bedienungsanleitung

902-290 6’ Sectional Slide

Page 1

Rev. 1/22/04

IMPORTANT

PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment

must be installed in accordance with these instructions. Check your shipment

against Bill of Lading and Parts list. Any missing or broken parts must be

reported to your distributor within 10 days of receipt of your order. When

properly installed and maintained, equipment will give many years of Safe,

Trouble-Free use. Periodically check for loose or broken parts. Loose bolts

must be tightened and broken parts must be replaced as they can possibly

create dangerous situations leading to unnecessary accidents. Resilient

Surfacing should be used under all playground equipment. Appropriate

publications, available at no charge, from the Consumer Product Safety

Commission, include “A Handbook for Public Playground Safety”. You can

receive your free copy by calling 1-301-504-7908.

PACKING LIST HARDWARE BAG

1 Hardware Bag 2 126-701 3/8” x 1 ¼” Button Head Bolt

1 6’ Sectional Slide 11 126-702 3/8” x ¾” Button Head Bolt

12 903-001 Pipe Clamp 2 226-602 3/8” Nylon Insert Lock Nut

3 903-002 Deck Clamp 15 316-601 3/8” Flat Washer

1 903-141 Spiral Slide Z Bracket 1 805-532 Warning Label

2 903-214 T Slide Leg 1 805-534 SportsPlay Label

1 903-286 Slide Center Support 1 Maintenance Checklist

1 903-306 Arch Entry Panel

1 903-324 Step Leg

2 903-327 Hand Rail

1 905-710 Triangle Deck

1 905-712 6’ deck steps

3 913-112 Post 12’6”

1 913-115 Slide Guard 48”

1 913-117 Ten Rung Wall

1 SKID 1 SLIDE 2 TOTAL PCS 953 # Weight Class 70

902-290 6’ Sectional Slide

Page 2

Rev. 1/22/04

GENERAL USE/FALL ZONE & FOOTING RECOMMENDATIONS

Stationary & Portable equipment – Use/Fall zones should extend a minimum of 6

feet in all directions from the perimeter of the equipment ground space.

This area should be covered with the required amount of resilient safety

surfacing material.

For some equipment – Use/Fall zones can overlap. See Consumer Product Safety

Commission Guidelines. Diameter and depth of footings illustrated are

satisfactory in most applications for pipe sizes up to 2 3/8” diameter.

Varying soil & climatic conditions may require deeper and heavier footings in

some areas. Check local building codes.

IF RESILIENT SURFACING IS TO BE LESS THAN 12”, THEN ADDITIONAL PIPE SHOULD BE

PUT IN CONCRETE TO MAINTAIN PROPER FINISH GRADE FOR EQUIPMENT.

USE AREA AND FOOTING LAYOUT:

(see page 1)

GENERAL ASSEMBLY INSTRUCTIONS:

Check all the parts and hardware with the packing list to be sure you have

received everything needed to assemble this product. CONTACT YOUR LOCAL

DISTRIBUTOR with notification of any missing or damaged parts. Contact MUST

be made within ten days of receipt of your order. Only hand-tighten nuts &

bolts on initial assembly. Final tightening should be done EVENLY after

nal assembly when unit has been plumbed & leveled.fi

GENERAL MAINTENANCE INSTRUCTIONS:

Check MONTHLY for loose bolts, damaged or broken parts.

ASSEMBLY AND INSTALLATION:

NOTE:

All threaded ends of bolts protruding beyond nuts must be cut off

and/or peened to eliminate sharp edges. No more than two threads

should extend beyond face of nut. All washers, “T” nuts, and other

fastener hardware used on round pipe or tubing must be hammered down to

conform to the curved underlying surface to eliminate catch points.

DO NOT tighten nuts more than hand-tight until entire assembly is

completed.

902-290 6’ Sectional Slide

Page 3

Rev. 1/22/04

NOTE:

Slides should be installed in shaded areas or face NORTH to prevent

direct sun on slide’s chute.

NOTE: Plumb and level entire unit. Tighten all nuts & Bolts until lock

washers are flat. Use short length of pipe on end of socket Key to add

leverage when tightening Socket Set Screws. Pour Concrete. Dome top

of cement for proper drainage. Wait 48 hours before removing braces,

applying resilient surfacing and using equipment.

NOTE: Attach warning label and Manufacturer’s Identification label to a clean

surface. The labels should be attached in a location where they are

clearly visible and legible and away from normal hand and foot

placement areas. The labels must be replaced if they become illegible,

destroyed or removed. Contact your SportsPlay distributor for

replacements.

902-290 6’ Sectional Slide

Page 4

Rev. 1/22/04

Installing deck clamps

Install deck clamps to the center of the deck corners. If clamps are off

center, then the line of posts will not be straight, nor will components

connect correctly. Picture shows deck clamp being tightened to post with a

3/8” X 1 ¼” Button Head bolt with a “T” nut on the deck side of the clamp. DO

NOT over tighten. If too tight the post will “swing.” Tighten when post is

level.

Decks attach to deck clamps using ½” X 2 ½” Button Head bolts washer on top

and bottom, with ½” lock nuts. Connect the deck bolt firmly.

Additional information on deck clamp and deck installation can be found in

the section entitled, “Building the First Deck.”

Building the first deck:

Lay deck on ground, use deck as “jig”. Place (4) deck clamps, one per

corner, spray paint through middle of clamp onto ground. These will be the

centers of the postholes. Remove deck and clamps. Dig the (4) holes 22”

deep and 12” wide. Holes are straight down and flat-bottomed. Install 10”

diameter plywood in hole bottoms.

902-290 6’ Sectional Slide

Page 5

Rev. 1/22/04

ck clamp set to corners

Dig first four holes

e marker to mark 22” from bottom of posts. Use these marks so you can run

a 4’ level across marks to make sure the tops of the posts are equal to each

other. If line marks are on bubble, then post tops should be on bubble to

each other.

Mark 22” from bottom of posts.

902-290 6’ Sectional Slide

Page 6

Rev. 1/22/04

Tighten deck and clamp hardware as you achieve level on all four posts and

e deck, there are two methods you can use. The BEST

Install red plastic end caps on post bottoms. Install 10” square plywood

squares in bottom of holes. Since your holes are 12” diameter and posts are

centered in holes you have approx. 3.5” all around the post. Block the posts

into center of holes when posts are on bubble. Use scrap lumber and wedges

to solidify the posts in their holes as you level the posts. Re-blocking may

be necessary at times in order to achieve level. You may also have to widen

your holes if they are not dug center.

sides of your deck-top.

When you go to install th

method is to make a table or stand to place your deck on at the required deck

height. The table will stabilize the deck so you can level it. Below is a

typical table. This one can be lowered or raised. You can make a table fro

sawhorses. Remember, you must raise the deck to compensate for the resilient

surfacing you will use. With the deck resting on the table, you can spend

902-290 6’ Sectional Slide

Page 7

Rev. 1/22/04

time leveling your posts to achieve bubble. Deck stand or table holds deck

while you build around it.

Blocks stabilize the posts while table stabilizes the deck.

The second method is to pre-install the (4) deck clamps so that there is 42

¼” between the holes in the deck clamps. Use a level and a marker to make

sure the clamps are level to each other. Then place deck onto clamps and

bolt. This method works but is less stable than the first method. The deck

and posts will stabilize more as you add components

Pre-install deck clamps and level.

Use ¼” Allen wrench on 3/8” by 1 ¼” button head bolt, with “T” nut. “T” nut

is on deck side of clamp so as to make tightening easier. When all (4)

clamps have been installed, posts and deck level, install roll pins.

902-290 6’ Sectional Slide

Page 8

Rev. 1/22/04

Use magnetic levels on all sides of the round posts. Always adjust the posts

into level by gently bumping the bottom with a construction bar. Trying to

push the posts into “bubble” in the top or middle will throw off your

evious work. Adjust the post levels carefully, not roughly.pr

When all (4) posts are plumb and stable, drill through the deck clamps and

into the posts with a ¼” metal drill bit. Install the ¾” roll pins so that

they are “flush” with the posts.

Attaching decks

Install the ½” by 2 ½” button head bolt with washer on top and on bottom

under ½” lock nut. Medium tighten to the corner. Drill through the vinyl

coating with ½” metal bit if necessary (fit may be tight).

902-290 6’ Sectional Slide

Page 9

Rev. 1/22/04

SportsPlay Equipment, Inc.,

TYPICAL DECK DEMENSIONS:

Decks are 48” square

A. Diagonal distance between post holes = 67.5”

B. Center to center between posts = 48”

C. Distance between bolt holes in deck clamps = 42 ¼”

Illustration on next page shows completed deck and (4) posts. Deck and post

are vertically and horizontally level and clamps are tight. Posts are center

to deck corners. Roll pins are installed. Avoid standing on decks until the

addition of more components and decks allow the work to become more stable.

When this happens, walk gently on decks. Usually a smaller person should

work on decks. You may use a stepladder to work on the outside of the decks

while a person stands on deck.

902-290 6’ Sectional Slide

Page 10

Rev. 1/22/04

SportsPlay Equipment, Inc.,

Posts must be blocked solidly for a stable, ongoing installation. Blocks are

removed just before concrete is installed.

Inhaltsverzeichnis

Andere SportsPlay Spielgeräte und Spielplatzausstattung Handbücher

SportsPlay

SportsPlay 301-146 10' MGR Bedienungsanleitung

SportsPlay

SportsPlay 581-830-8M Bedienungsanleitung

SportsPlay

SportsPlay 581-442HD Bedienungsanleitung

SportsPlay

SportsPlay 581-830H Bedienungsanleitung

SportsPlay

SportsPlay 581-830-8F Bedienungsanleitung

SportsPlay

SportsPlay 511-102 Bedienungsanleitung

SportsPlay

SportsPlay 902-706 Gebrauchsanweisung

SportsPlay

SportsPlay 581-630F Bedienungsanleitung

SportsPlay

SportsPlay 511-107 Bedienungsanleitung

SportsPlay

SportsPlay JR GEO-DOME Bedienungsanleitung

SportsPlay

SportsPlay 581-218 Bedienungsanleitung

SportsPlay

SportsPlay 581-438M Bedienungsanleitung

SportsPlay

SportsPlay Mega Series Bedienungsanleitung

SportsPlay

SportsPlay 581-630-8M Bedienungsanleitung

SportsPlay

SportsPlay 581-438F Bedienungsanleitung

SportsPlay

SportsPlay 581-440HD Bedienungsanleitung

SportsPlay

SportsPlay 581-630M Bedienungsanleitung

SportsPlay

SportsPlay Seth Mega Installations- und Betriebshandbuch

SportsPlay

SportsPlay QUICK SHIP 1 MODIFIED Bedienungsanleitung

SportsPlay

SportsPlay ZACK Bedienungsanleitung

SportsPlay

SportsPlay 301-147 Bedienungsanleitung

SportsPlay

SportsPlay 581-438H Bedienungsanleitung

SportsPlay

SportsPlay 581-643H Bedienungsanleitung

SportsPlay

SportsPlay 581-230F Bedienungsanleitung

Beliebte Spielgeräte und Spielplatzausstattung Handbücher anderer Marken

FUNormous

FUNormous Disney Junior MICKEY MOUSE Bedienungsanleitung

b4Adventure

b4Adventure Slackers TREEZONE ADVENTURE THREE HOUSE Bedienungsanleitung

PoolMaster

PoolMaster 72775 Bedienungsanleitung

Palmako

Palmako 4743142009857 Installationshandbuch

BOERPLAY

BOERPLAY PSTE000.019 Bedienungsanleitung

MGA Entertainment

MGA Entertainment Little Tikes Dunk'n Toss Bouncer Benutzerhandbuch

stilum

stilum Erika Bedienungsanleitung

Costway

Costway NP10816 Bedienungsanleitung

Trigano

Trigano VABI Bedienungsanleitung

Outward

Outward OUT116 Bedienungsanleitung

GALOPIN

GALOPIN ARC02 Bedienungsanleitung

stilum

stilum levis Technische Daten

Ledon

Ledon BASIC Bai LB012 Bedienungsanleitung

BOERPLAY

BOERPLAY PSTE115.002 Bedienungsanleitung

Europlay

Europlay S306 Programmierhandbuch

SportsPlay Equipment

SportsPlay Equipment 361-509H Bedienungsanleitung

Ledon

Ledon 302250 Bedienungsanleitung

Costway

Costway NP10441 Bedienungsanleitung