ST STM32 Nucleo Bedienungsanleitung
Introduction
The STM32 Nucleo-64 board, based on the MB1717 reference board (NUCLEO-C031C6 order code) provides an affordable
and flexible way for users to try out new concepts and build prototypes with various combinations of performance, power
consumption, and features.
The ARDUINO® Uno V3 connectivity support and the ST morpho headers provide an easy means of expanding the functionality
of the STM32C0 Nucleo open development platform with a wide choice of specialized shields.
The STM32 Nucleo-64 board does not require any separate probe, as it integrates the ST-LINK/V2-1 debugger/programmer.
The STM32 Nucleo-64 board comes with the comprehensive free STM32 software libraries and examples that are available with
the STM32CubeC0 MCU Package.
Figure 1. NUCLEO-C031C6 board (Top view)
Picture is not contractual.
STM32 Nucleo-64 board (MB1717)
UM2953
User manual
UM2953 - Rev 1 - February 2022
For further information contact your local STMicroelectronics sales office. www.st.com
1Features
• STM32C031C6 microcontroller based on the Arm® Cortex®-M0+ processor with 32-Kbyte Flash memory
and 12-Kbyte SRAM, in an LQFP48 package
• User LED shared with ARDUINO®
• User and reset push-buttons
• 32.768 kHz crystal oscillator
• Board connectors:
– ARDUINO® Uno V3 expansion connector
– ST morpho extension pin headers for full access to all STM32C0 I/Os
• Flexible power-supply options: ST-LINK USB VBUS or external sources
• On-board ST-LINK/V2-1 debugger/programmer with USB re-enumeration capability: mass storage, Virtual
COM port, and debug port
• Comprehensive free software libraries and examples available with the STM32CubeC0 MCU Package
• Support of a wide choice of Integrated Development Environments (IDEs) including IAR Embedded
Workbench®, MDK-ARM, and STM32CubeIDE
Note: Arm is a registered trademark of Arm Limited (or its subsidiaries) in the US and/or elsewhere.
UM2953
Features
UM2953 - Rev 1 page 2/32
2Ordering information
To order the NUCLEO-C031C6 Nucleo-64 board, refer to Table 1. Additional information is available from the
datasheet and reference manual of the target STM32.
Table 1. Ordering information
Order code Board reference Target STM32
NUCLEO-C031C6 MB1717 STM32C031C6T6
2.1 Codification
The meaning of the codification is explained in Table 2.
Table 2. Codification explanation
NUCLEO-XXYYTZ Description Example: NUCLEO-C031C6
XX MCU series in STM32 32-bit Arm Cortex MCUs STM32C0 Series
YY Product line in the Series STM32C0x1 product line
TSTM32 package pin count:
• C for 48 pins 48‑pin package
ZSTM32 Flash memory size:
• 6 for 32 Kbytes 32‑Kbyte Flash memory
UM2953
Ordering information
UM2953 - Rev 1 page 3/32
3Development environment
3.1 System requirements
• Multi‑OS support: Windows® 10, Linux® 64-bit, or macOS®
• USB Type-A or USB Type-C® to Micro-B cable
Note: macOS® is a trademark of Apple Inc., registered in the U.S. and other countries and regions.
Linux® is a registered trademark of Linus Torvalds.
All other trademarks are the property of their respective owners.
3.2 Development toolchains
• IAR Systems® - IAR Embedded Workbench®(1)
• Keil® - MDK-ARM(1)
• STMicroelectronics - STM32CubeIDE
1. On Windows® only.
3.3 Demonstration software
The demonstration software, included in the STM32Cube MCU Package corresponding to the on-board
microcontroller, is preloaded in the STM32 flash memory for easy demonstration of the device peripherals in
standalone mode. The latest versions of the demonstration source code and associated documentation can be
downloaded from www.st.com.
UM2953
Development environment
UM2953 - Rev 1 page 4/32
4Conventions
Table 3 provides the conventions used for the ON and OFF settings in the present document.
Table 3. ON/OFF convention
Convention Definition
Jumper JPx ON Jumper fitted
Jumper JPx OFF Jumper not fitted
Jumper JPx [1-2] Jumper fitted between Pin 1 and Pin 2
Solder bridge SBx ON SBx connections closed by 0 Ω resistor
Solder bridge SBx OFF SBx connections left open
Resistor Rx ON Resistor soldered
Resistor Rx OFF Resistor not soldered
Capacitor Cx ON Capacitor soldered
Capacitor Cx OFF Capacitor not soldered
UM2953
Conventions
UM2953 - Rev 1 page 5/32
5Quick start
This section describes how to quickly start development using NUCLEO-C031C6.
To use the product, the user must accept the Evaluation Product License Agreement from the www.st.com/epla
webpage.
For more information on the STM32 Nucleo-64 board and demonstration software, visit the www.st.com/
stm32nucleo webpage.
5.1 Getting started
Follow the sequence below to configure the STM32 Nucleo-64 board and launch the demonstration application
(Refer to Figure 3 for component location):
1. Check jumper positions on board: CN2 ST-LINK [1-2] and [3-4], JP5 PWR [1-2], and JP6 ON.
2. For correct identification of all device interfaces from the host PC, install the Nucleo USB driver available on
the www.st.com/stm32nucleo web page, before connecting the board.
3. To power the board, connect the STM32 Nucleo-64 board to a PC with a USB Type-A or USB Type-C® to
Micro-B cable through the CN1 USB connector. Once powered on, the LD3 PWR green LED lights up and
LD1 COM LED blinks.
4. Press the B1 blue user button.
5. Observe that the blinking frequency of the LD4 three green LEDs changes, by clicking on the B1 button.
6. The demonstration software and several software examples showing how to use the STM32 Nucleo features
are available from the NUCLEO-C031C6 product location.
UM2953
Quick start
UM2953 - Rev 1 page 6/32
6Hardware layout and configuration
The NUCLEO-C031C6 Nucleo-64 board is designed around the STM32C031C6T6 microcontroller in a 48-pin
LQFP package.
The hardware block diagram in Figure 2 illustrates the connections between the NUCLEO-C031C6
microcontroller and its peripherals, such as the ARDUINO® Uno V3 connector, ST morpho connector,
push‑button, and embedded ST-LINK/V2-1).
Figure 3 and Figure 4 help the user to locate these features on the STM32 Nucleo-64 board. The mechanical
dimensions of the NUCLEO-C031C6 product are shown in Figure 5.
Figure 2. Hardware block diagram
Embedded
ST-LINK/V2-1
STM32
microcontroller
RESET
SWD
ST morpho extension header
ST morpho extension header
B2
RESET
B1
USER
ARDUINO® connector
LED
LD4
ST-LINK part
MCU part
USB
Micro-B
UART
IO
IO
IO
IO
ARDUINO® connector
UM2953
Hardware layout and configuration
UM2953 - Rev 1 page 7/32
Figure 3. NUCLEO-C031C6 PCB top side
UM2953
Hardware layout and configuration
UM2953 - Rev 1 page 8/32
Figure 4. NUCLEO-C031C6 PCB bottom side
UM2953
Hardware layout and configuration
UM2953 - Rev 1 page 9/32
6.1 STM32 Nucleo-64 board mechanical drawing
Figure 5. STM32 Nucleo-64 board mechanical dimensions (in millimeters)
UM2953
STM32 Nucleo-64 board mechanical drawing
UM2953 - Rev 1 page 10/32
Andere Handbücher für STM32 Nucleo
19
Inhaltsverzeichnis
Andere ST Computerhardware Handbücher
ST
ST TDA911 Series Montage- und Bedienungsanleitung
ST
ST X-NUCLEO-53L5A1 Bedienungsanleitung
ST
ST STM32F3 Series Betriebsanleitung
ST
ST X-NUCLEO-GFX01M1 Bedienungsanleitung
ST
ST X-NUCLEO-IHM14A1 Bedienungsanleitung
ST
ST X-NUCLEO-OUT15A1 Bedienungsanleitung
ST
ST X-STM32MP-MSP01 Bedienungsanleitung
ST
ST X-NUCLEO-53L8A1 Bedienungsanleitung
ST
ST EVLONE65W Bedienungsanleitung
ST
ST STM32G0 Bedienungsanleitung
ST
ST STM32U5G9J-DK2 Bedienungsanleitung
ST
ST STM8SVLDISCOVERY Montage- und Bedienungsanleitung
ST
ST STEVAL-IFP046V1 Bedienungsanleitung
ST
ST X-NUCLEO-S2868A2 Bedienungsanleitung
ST
ST EVAL6470H-DISC Bedienungsanleitung
ST
ST X-NUCLEO-S2915A1 Bedienungsanleitung
ST
ST STA309A Bedienungsanleitung
ST
ST X-NUCLEO-BNRG2A1 Bedienungsanleitung
ST
ST ControlBD-7FMC2 Bedienungsanleitung
ST
ST STSW-L9026-Y0 Bedienungsanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
