ST STM32F101 series Bedienungsanleitung

October 2007 Rev 1 1/14

UM0462

User manual

STM32F101xx and STM32F103xx

Flash loader demonstrator

Introduction

The purpose of this document is to describe the STMicroelectronics STM32F101xx and

STM32F103xx Flash loader demonstrator application that was developed to illustrate the

System Memory bootloader capabilities.

This document details the prerequested hardware and software environments, as well as

the use cases of the demonstrator software.

www.st.com

Contents UM0462

2/14

Contents

1 Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.1 Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.1.1 Software contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.1.2 Hardware contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.3 Flash loader demonstrator installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.3.1 Software installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.3.2 Hardware installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 User interface description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

UM0462 List of figures

3/14

List of figures

Figure 1. System Properties dialog box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Figure 2. Device Manager window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Figure 3. Welcome window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Figure 4. Connection settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Figure 5. Device information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Figure 6. Operation choice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Figure 7. Operation progress. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Getting started UM0462

4/14

1 Getting started

1.1 Package contents

The following items are supplied in the Flash loader demonstrator package:

1.1.1 Software contents

1. STBLLIB.dll: a dynamic link library implementing the system memory bootloader

protocol and the COM communication APIs.

2. Files.dll: a dynamic link library implementing the needed file manipulation APIs to load

and store binary, hexadecimal and motorola S19 files.

3. STMicroelectronics flash loader.exe: a wizard application that provides the high-level

operations that can be performed by the user.

1.1.2 Hardware contents

This tool is designed to work with all STMicroelectronics devices that support the system

memory bootloader protocols. For more details, please visit the STMicroelectronics website

(http://www.st.com) and refer to the application note AN2606: “STM32F101xx and

STM32F103xx system memory boot mode”.

1.2 System requirements

In order to use the Flash loader demonstrator with the Windows operating system, a recent

version of Windows, such as Windows 98, Millennium, 2000, XP or Vista, must be installed

on the PC.

The version of the Windows OS installed on your computer may be determined by right-

clicking on the “My Computer” icon on the desktop, then clicking on the “Properties” item in

the displayed pop-up menu. The OS type is displayed in the “System Properties” dialog box

under the “System” label as shown in Figure 1.

UM0462 Getting started

5/14

Figure 1. System Properties dialog box

For the communication, you need to verify that you have an available COM port(RS232) as

one COM port is required for system connection.

To check that you have an available communication port, right-click on the “My Computer”

icon on the desktop and select “Properties” from the pop-up menu. The “System Properties”

dialog box appears. Click on the “Hardware” tab, and then on the “Device manager” button

to display the system hardware configuration. Available COM ports are grouped under the

”Ports (COM & LPT)” node in the hardware tree as shown in Figure 2.

Getting started UM0462

6/14

Figure 2. Device Manager window

1.3 Flash loader demonstrator installation

1.3.1 Software installation

Run the UM0462.exe file: the InstallShield Wizard will guide you to install Flash loader

demonstrator application on your computer. When the software is successfully installed,

click on the “Finish” button.

1.3.2 Hardware installation

Connect the device to a spare COM port on your PC.

UM0462 User interface description

7/14

2 User interface description

The Flash loader demonstrator is designed as a wizard application. It is structured into five

steps, the:

●welcome page

●connection settings

●device information

●operation choice

●operation progress

Step 1

Run the Flash loader demonstrator from the “Programs” menu (connection to the device has

not been made yet) then, make sure that the device is connected to your PC and reset it to

restart the system memory bootloader code. The Welcome window shown in Figure 3

appears.

If all is ready click “Next” to continue.

Figure 3. Welcome window

User interface description UM0462

8/14

Step 2

The second step consists in selecting the connection settings. Select the desired UART

settings (port name, baud rate, data bits, parity and stop bits and timeout) as shown in

Figure 4. The default configuration is automatically set.

Ensure that the boot configuration pins are set correctly, then reset the device and click

“Next” to continue. If a connection has been established, the wizard moves to the next step,

otherwise a message box is displayed that indicates the error that occurred.

Figure 4. Connection settings

UM0462 User interface description

9/14

Step 3

In this step the connection has been established and communication has started.

The Wizard displays the available device information such as the target ID or the number of

times the read protection is disabled/enabled.

Select the target name in the target combobox as shown in Figure 5, then click on “Next” to

continue.

Figure 5. Device information

User interface description UM0462

10/14

Step 4

At this step, select the requested operation –Erase, Download or Upload– and set the

related parameters:

●Erase

– Select the “All” button to erase the whole memory

– Select the “Selection” button to customize the Erase operation. Click on the

“Selection” button to display the memory mapping dialog window, then check the

pages to be erased and click “Ok”.

●Download

– Click the related browse button to open a binary, hexadecimal or S19 Motorola file.

If the loaded file is a binary file, the download address is the start address of the first

page and the “@” field is still editable to accept changes.

If the loaded file is a hexadecimal or an S19 motorola file, the download address is

the start address of the first record in the file, and the “@” field is read-only.

– Check the “Verify” check box to launch the verification process when the Download

operation is finished.

– Check “Jump to the user program” to launch the downloaded program.

– Check the “Optimize download duration” to filter FFs packets (256 bytes).

– Check ”Enable read protection after download” to activate the Flash memory read

protection.

●Upload

– Click the related browse button to select which binary, hexadecimal or S19 motorola

file will store the uploaded data.

Note: Erase and Download operations can be performed only if the write protection is disabled.

Consequently, the software will automatically disable the write protection before launching

the operation.

For Upload operations, the software will automatically disable the read protection before

launching the operation.

Andere Handbücher für STM32F101 series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ST Mikrocontroller Handbücher

ST STM32F429I-DISCO Bedienungsanleitung

ST UM2975 Bedienungsanleitung

ST SPC582B Series Montage- und Bedienungsanleitung

ST AN3155 Montage- und Bedienungsanleitung

ST STM32CubeL5 Bedienungsanleitung

ST STM32H7 3 Series Montage- und Bedienungsanleitung

ST STR71xF Bedienungsanleitung

ST STEVAL-IDB007V1M SPBTLE-1S Bedienungsanleitung

ST STM32 Nucleo Montage- und Bedienungsanleitung

ST STEVAL-STWINKT1 Bedienungsanleitung

ST STM32U585 Series Bedienungsanleitung

ST STM32 Nucleo Bedienungsanleitung

ST P-NUCLEO-WB55 Bedienungsanleitung

ST STM32F0DISCOVERY Bedienungsanleitung

ST STM32F103 series Montage- und Bedienungsanleitung

ST STM32F74 Series Bedienungsanleitung

ST STEVAL-FKI433V1 Bedienungsanleitung

ST STM32F0 Series Montage- und Bedienungsanleitung

ST SimpleMAC STM32W108 Series Bedienungsanleitung

ST UC2842B Bedienungsanleitung

ST SPC58EC-DISP Bedienungsanleitung

ST STM32L0 Series Montage- und Bedienungsanleitung

ST STM32F7508-DK Handbuch

ST STM32F10 Series Montage- und Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung

Silicon Laboratories

Silicon Laboratories C8051F800 Bedienungsanleitung

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Bedienungsanleitung