ST SPC584BADPT176S Bedienungsanleitung

Introduction

The SPC584BADPT176S Rev.A evaluation board supports STMicroelectronics SPC584BxxE7, SPC584CxxE7 and

SPC58ECxxE7 microcontrollers in LQFP 176 package.

Figure 1. SPC584BADPT176S Rev.A

Picture is not contractual

SPC584BADPT176S Rev.A evaluation board

UM2756

User manual

UM2756 - Rev 1 - August 2020

For further information contact your local STMicroelectronics sales office.

www.st.com

1Overview

The SPC584BADPT176S mini module is an evaluation board supporting STMicroelectronics SPC584BxxE7,

SPC584CxxE7 and SPC58ECxxE7 microcontrollers in LQFP176 package.

The mini module is designed to be connected onto the SPC58xxMB motherboard, offering a mechanism for easy

customer evaluation of the supported devices, and to facilitate hardware and software development.

The mini module may be used as a stand-alone unit allowing access to the CPU, but no access to the I/O pins as

any motherboard peripherals.

Figure 2. Overview of SPC584BADPT176S mini module - top

UM2756

Overview

UM2756 - Rev 1 page 2/24

Figure 3. Overview of SPC584BADPT176S mini module - bottom

1.1 Package contents

An SPC584BADPT176S adapter package includes the following item:

• SPC584BADPT176S mini module

1.2 Supported devices

The SPC584BADPT176S mini module supports the following STMicroelectronics family of microcontrollers in

LQFP176 package:

• SPC584BxxE7

• SPC584CxxE7

• SPC58ECxxE7

UM2756

Package contents

UM2756 - Rev 1 page 3/24

2License agreement

The packaging of this evaluation board was sealed with a seal stating, “by breaking this seal, you agree to the

terms and conditions of the evaluation board license agreement, the terms and conditions of which are available

at http://www.st.com/ebla”. Upon breaking the seal, you and STMicroelectronics entered into the evaluation board

license agreement, a copy of which is also enclosed with the evaluation board for convenience.

Attention: This evaluation board only offers limited features for evaluating ST products. It has not been tested for use with

other products and is not suitable for any safety or other commercial or consumer application. This evaluation

board is otherwise provided “AS IS” and STMicroelectronics disclaims all warranties, express or implied,

including the implied warranties of merchantability and fitness for a particular purpose.

UM2756

License agreement

UM2756 - Rev 1 page 4/24

3Handling precautions

Please take care to handle the package contents in a manner such as to prevent electrostatic discharge.

Before the EVB is used or power is applied, please fully read the following sections on how to correctly configure

the board. Failure to correctly configure the board may cause irreparable component, MCU or EVB damage.

UM2756

Handling precautions

UM2756 - Rev 1 page 5/24

4Hardware description

4.1 Hardware features

The SPC584BADPT176S mini module board has the following features:

• Connector for external power supplies input (5.0 V, 3.3 V, 1.25 V) used in stand-alone mode

• Reset button with driver and led indicator

• Socket for device in eLQFP176 package with exposed pad down

• Debug ports:

– 38-pin Nexus Mictor connector for Nexus parallel interface

– 14-pin header connector for JTAG port

– 12-pin header connector for LFAST interface

• 40 MHz crystal main oscillator with jumpers to optionally disconnect it

• 8 MHz oscillator with jumpers to optionally disconnect it

• Clock input through SMA connector to optionally disconnect it

• 2 X SAMTEC QSH series, 240-way connector to connect mini module to motherboard

4.2 Hardware dimension

The mini module has the following dimensions:

• PCB area: 127 mm X 114.3 mm

• Top components height: 19.4 mm max

• Bottom components height: 3.5 mm max

• PCB thickness: 1.6 mm

UM2756

Hardware description

UM2756 - Rev 1 page 6/24

5Power and system configuration

5.1 Power supplies

When the mini module is plugged onto the motherboard, power is supplied directly by the motherboard. In this

setup, the external power supply input available on the mini module should NOT be used.

When the SPC584BADPT176S mini module is used as a stand-alone board, external power supplies must be

used (5.0 V, 3.3 V, 1.25 V).

The following jumpers are used to configure the power supply:

Table 1. Power configuration jumpers

Jumper Description Default Position

VDD_HV_ADR voltage selenction - from

• 1-2 5.0V_LR

• 3-2 5.0V_SR

• 4-2 3.3V_SR

1-2 (5.0V_LR) Figure 4. SPC584BADPT176S top mini

module view - C2

VDD_HV_ADV voltage selection - from

• 1-2 5.0V_LR

• 3-2 5.0V_SR

• 4-2 3.3V_SR

1-2 (5.0V_LR) Figure 4. SPC584BADPT176S top mini

module view - B2

VDD_HV_JTAG voltage selection - from

• 1-2 5.0V_SR

• 3-2 3.3V_SR

1-2 (5.0V_SR) Figure 4. SPC584BADPT176S top mini

module view - B2

VDD_HV_IO_MAIN voltage selection - from

• 1-2 5.0V_SR

• 3-2 3.3V_SR

1-2 (5.0V_SR) Figure 4. SPC584BADPT176S top mini

module view - B2

VDD_HV_IO_FLEX voltage selection - from

• 1-2 5.0V_SR

• 3-2 3.3V_SR

1-2 (5.0V_SR) Figure 4. SPC584BADPT176S top mini

module view - B2

J45

Supply of the BALLAST circuit

• 1-2 VDD_HV_IO_MAIN

• 3-2 5.0_SR

1-2

(VDD_HV_IO_MAIN)

Figure 4. SPC584BADPT176S top mini

module view - A2

J40

VDD_LV voltage selection - from

• 1-2 BALLAST circuit

• 3-2 1.25V_SR

• 4-2 SMPS_REGULATOR_OUT

2-3 (1.25V_SR) Figure 4. SPC584BADPT176S top mini

module view - A3

UM2756

Power and system configuration

UM2756 - Rev 1 page 7/24

5.2 Port configuration

The following jumper need to configure the ports:

Table 2. Ports related jumpers

Jumper Description Default Position

J30 TESTMODE settings Close Figure 4. SPC584BADPT176S top mini module view -

J13

PH[12]/EVTI connection to QSH motherboard

connectors

• 1-2 PH12

• 3-2 EVTI

1-2 (PH12) Figure 4. SPC584BADPT176S top mini module view -

J31

PJ[3]/EVTO connection to QSH motherboard

connectors.

• 1-2 PJ3 (allowed)

• 3-2 EVTO (reserved)

1-2 (PJ3) Figure 4. SPC584BADPT176S top mini module view -

J42

PA8/TDI_TxDATA_N connection to QSH

motherboard connectors or LFAST

INTERFACE

Close 2-3 Figure 4. SPC584BADPT176S top mini module view -

J43

PA9/TDO_RxDATA_P connection to QSH

motherboard connectors or LFAST

INTERFACE

Close 2-3 Figure 4. SPC584BADPT176S top mini module view -

J44 PA14/RDY connection to QSH motherboard

connectors or Nexus parallel interface Close 2-3 Figure 4. SPC584BADPT176S top mini module view -

J41

EVTO/ESR0 connection

Configuration 1-2 allowed, Configuration 2-3

Reserved.

Close 1-2 Figure 4. SPC584BADPT176S top mini module view -

5.3 System clock configuration

The mini module supports the usage of crystal clock sources as well as external clock source:

Table 3. Clock configuration jumpers

Jumper Description Default Position

J21 40 MHz crystal clock source Enable

for pin EXTAL 1-2 (XT1 pin2) Figure 4. SPC584BADPT176S top mini module view -

J23 40 MHz crystal clock source Enable

for pin XTAL 1-2 (XT1 pin1) Figure 4. SPC584BADPT176S top mini module view -

J22 Enable 8 MHz oscillator power supply Open Figure 4. SPC584BADPT176S top mini module view -

J24 External clock source from 8 MHz

oscillator or SMA connector

1-2 (8 MHz

oscillator)

Figure 4. SPC584BADPT176S top mini module view -

UM2756

Port configuration

UM2756 - Rev 1 page 8/24

5.4 Reset circuit

The mini module supports different ways to reset the microcontroller.

To use and perform the reset driving there are different jumpers and switches:

Table 4. Reset configuration jumpers

Jumper Description Default Position

SW1 Reset push button Open Figure 4. SPC584BADPT176S top mini module view - D1

J27

Connect the external reset to the reset driver

for

ESR0 and PORST pins

Close Figure 4. SPC584BADPT176S top mini module view - D1

J25 Connect the external reset to ESR0 pin Close Figure 4. SPC584BADPT176S top mini module view - D2

J26 Connect the external reset to PORST pin Close Figure 4. SPC584BADPT176S top mini module view - D2

5.5 Test points

The mini module has several test points. Below all test point description:

Table 5. Test points

Test point Description Position

TP0 VDD_HV_IO_MAIN test point Figure 4. SPC584BADPT176S top mini module view - D4

TP1 VSS_OSC test point Figure 4. SPC584BADPT176S top mini module view - D3

TP2 AGND test point Figure 4. SPC584BADPT176S top mini module view - D3

TP3 JCOMP_RxDATA_N/PA[5] test point Figure 4. SPC584BADPT176S top mini module view - A2

TP4 TCK/PA[6] test point Figure 4. SPC584BADPT176S top mini module view - A2

TP5 TMS_TxDATA_P/PA[7] test point Figure 4. SPC584BADPT176S top mini module view - A3

TP6 TDI_TxDATA_N/PA[8] test point Figure 4. SPC584BADPT176S top mini module view - A3

TP7 TDO_RxDATA_P/PA[9] test point Figure 4. SPC584BADPT176S top mini module view - A3

TP16 PA[0] test point Figure 4. SPC584BADPT176S top mini module view - A4

TP17 PB8 Figure 4. SPC584BADPT176S top mini module view - C3

TP18 PE3 Figure 4. SPC584BADPT176S top mini module view - B4

TP22 J16A, QSH connector, pin10 test point Figure 4. SPC584BADPT176S top mini module view - A4

TP25 J16A, QSH connector, pin12 test point Figure 4. SPC584BADPT176S top mini module view - B4

TP28 J16A, QSH connector, pin11 test point Figure 4. SPC584BADPT176S top mini module view - A4

UM2756

Reset circuit

UM2756 - Rev 1 page 9/24

5.6 Connectors

The mini module has other connectors described in the below table.

Table 6. Other connectors

Connectors Description Position

J20 12-pin header connector for SIPI interface Figure 4. SPC584BADPT176S top mini module view - C2

J18 14-pin header connector for JTAG port Figure 4. SPC584BADPT176S top mini module view - A4

CN1 12-pin SAMTEC connector for JTAG/LFAST

LVDS interface Figure 4. SPC584BADPT176S top mini module view - A3

J36, J37 DC-DC Regulator Module Figure 4. SPC584BADPT176S top mini module view - A1/A2

J16, J17 2 X SAMTEC QSH series, 240-way connector to

connect mini module to motherboard Figure 5. SPC584BADPT176S bottom mini module view

UM2756

Connectors

UM2756 - Rev 1 page 10/24

Inhaltsverzeichnis

Andere ST Hauptplatine Handbücher

ST STM32303C-EVAL Bedienungsanleitung

ST EVAL-7803APSO-SA Bedienungsanleitung

ST STM8L1526-EVAL Bedienungsanleitung

ST EVAL-FDA903U-SA Bedienungsanleitung

ST STEVAL-1PS03A Bedienungsanleitung

ST NUCLEO-G070RB Bedienungsanleitung

ST X-NUCLEO-NFC03A1 Bedienungsanleitung

ST STEVAL-L99615C Bedienungsanleitung

ST STEVAL-PCC010V1 Bedienungsanleitung

ST STM32303E-EVAL Bedienungsanleitung

ST EVALSP1310CPU Bedienungsanleitung

ST EVSPIN32G4-DUAL Bedienungsanleitung

ST STEVAL-IPE005V1 Bedienungsanleitung

ST P-NUCLEO-USB002 Bedienungsanleitung

ST X-NUCLEO-IDW01M1 Bedienungsanleitung

ST UM0527 Bedienungsanleitung

ST Teseo-VIC3DA Bedienungsanleitung

ST STEVAL-PLC001V1 Bedienungsanleitung

ST STEVAL-DIGAFEV1 Bedienungsanleitung

ST STM32 Nucleo Bedienungsanleitung

ST EVALSP1340CPU Bedienungsanleitung

ST STEVAL-ISB68WA Bedienungsanleitung

ST SPC574KADPT144S Bedienungsanleitung

ST UM2711 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung