ST STEVAL-MKI132V1 Bedienungsanleitung

Looking for a discount?

Check out our current promotions!

This coversheet was created by Verical, a division of Arrow Electronics, Inc. (“Verical”). The attached document was created by the part supplier,

not Verical, and is provided strictly 'as is.' Verical, its subsidiaries, afﬁliates, employees, and agents make no representations or warranties

regarding the attached document and disclaim any liability for the consequences of relying on the information therein. All referenced brands,

product names, service names, and trademarks are the property of their respective owners.

00000005981LF-000

EOS Power

Buy Now

We have 45,000 LP502030-PCM-NTC-LD-A02554 - EEMB - Lithium Battery Rectangular 3.7V 250mAh Rechargeable in

stock now. Starting at $0.034. This EEMB part is fully warrantied and traceable.

1-855-837-4225

Give us a call

International: 1-555-555-5555 1-415-281-3866

1-415-281-3866

Arrow Electronics,

Verical Division

P.O. Box 740970

Los Angeles, CA 90074-0970

Arrow Electronics, Inc

9201 East Dry Creek Road

Centennial, CO 80112

STEVAL-MKI132V1

STMICROELECTRONICS

Buy Now

January 2013 Doc ID 023744 Rev 1 1/26

UM1579

User manual

STEVAL-MKI132V1- BlueMotion motherboard for MEMS

adapter boards

Introduction

The STEVAL-MKI132V1 (BlueMotion) motherboard is designed to provide the user with a

complete ready-to-use platform for the demonstration of MEMS devices mounted on

adapter boards.

This STEVAL-MKI132V1 demonstration board uses an STM32F103TB microcontroller and

an SPBT2532C2.AT Bluetooth

module; it functions as a bridge between the sensor on the

adapter board and the PC. It is possible to connect the BlueMotion to the PC using the

Bluetooth module and using the Unico graphical user interface (GUI), downloadable from

the ST website, or dedicated software routines for customized applications.

This user manual describes the hardware included with the demonstration board and

provides the information required to install and run the demonstration board user interface.

For details regarding the features of each sensor, please refer to the datasheets available for

each individual device.

www.st.com

Contents UM1579

2/26 Doc ID 023744 Rev 1

Contents

1 Demonstration board description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 BlueMotion board installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.1 Establishing Bluetooth connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3 Supported MEMS adapter boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4 Supported commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.1 Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.2 Supported commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.2.1 Commands list and description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4.2.2 Digital output accelerometers: supported commands . . . . . . . . . . . . . . 19

4.2.3 Digital output gyroscopes: supported commands . . . . . . . . . . . . . . . . . 20

4.2.4 Digital output magnetometers: supported commands . . . . . . . . . . . . . . 20

4.3 Quick start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

5 Schematic diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

6 Bill of materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

7 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

UM1579 Demonstration board description

Doc ID 023744 Rev 1 3/26

1 Demonstration board description

The BlueMotion is a complete demonstration board that allows the demonstration of both

digital and analog MEMS sensors. Thanks to its DIL 24 connector, a wide range of MEMS

adapter boards can be used.

The block diagram of the demonstration board is shown in Figure 1.

Figure 1. Demonstration board block diagram

As shown in Figure 1, the BlueMotion demonstration board is based on the STM32F103TB

microcontroller and can be connected to the PC through Bluetooth. Data coming from the

MEMS sensor connected to the board can be read through the PC GUI provided with the

board.

The BlueMotion can be flashed with compatible firmware using an SWD connector or a

UART connector. See www.st.com/mems for new firmware releases.

The following steps are required to flash the board using UART:

1. Connect the BlueMotion to the PC using a UART connector (use the FS and ST pins of

the J2 connector shown in Figure 10).

2. Set the BOOT0 pin of the DIL 24 device adapter high.

3. Power up the board.

4. Use the STM32 flash loader utility to establish a UART connection with the BlueMotion.

The recommended settings are shown in Figure 2.

STM32F103TB

µC

MEMS

device Bluetooth

UART

Interrupt LEDs

General Purpose LEDs

DIL 24

Connector

I2C

AM14726V1

Demonstration board description UM1579

4/26 Doc ID 023744 Rev 1

Figure 2. Connecting BlueMotion using UART

Download the hexadecimal file of the firmware on BlueMotion using the STM32 flash loader

utility. For further details, refer to the utility’s user manual.

Figure 3. Downloading firmware using UART

AM14752V1

AM14753V1

UM1579 Demonstration board description

Doc ID 023744 Rev 1 5/26

Figure 4. Connecting BlueMotion using UART

The BlueMotion also integrates one general purpose LED, and two LEDs connected directly

to the interrupt pins of the digital adapters.

The top view and the bottom view of the full board are shown in Figure 5 and Figure 6

respectively.

AM14754V1

Demonstration board description UM1579

6/26 Doc ID 023744 Rev 1

Figure 5. Board top view

Figure 6. Board bottom view

The BlueMotion demonstration board can be used with the Unico GUI interface which allows

simple interaction with the sensor. The steps required for establishing a Bluetooth

connection with the board and accessing it are discussed in the following sections.

ref 2

ref 1

ref 3

ref 4

ref 5

ref 6

AM14727V1

AM14728V1

UM1579 Demonstration board description

Doc ID 023744 Rev 1 7/26

In Figure 5 some of the main components placed on the top layer of the BlueMotion board

are highlighted.

●

The dual power supply connector J1 (Figure 5, ref 1) can be used to supply power in

one of the two possible modes. Pin 2 on must be connected to ground. The board can

be powered with either a 1.5 V supply, e.g. an AA battery, connected to Pin 1 or with a

supply in the range 3.5 V - 6.0 V. connected to Pin 3.

●

The SWD connector J3 can (Figure 5, ref 2) be used to program the BlueMotion board.

●

Jumper JP1 allows the user to measure the sensor current consumption by connecting

a multimeter in series with its terminals when a 1.5 V power supply is used (Figure 5,

ref 3).

●

Jumper JP2 allows the user to measure the sensor current consumption by connecting

a multimeter in series with its terminals when a power supply in the range 3.5 V - 6.0 V

is used (Figure 5, ref 4).

BlueMotion also integrates three LEDs:

●

LED D5 (Figure 5, ref 5) is a general purpose LED and is used to indicate some

firmware states.

●

LEDs D6 and D7 (Figure 5, ref 6) are directly connected to the interrupt pins of the

MEMS digital adapters (if available on the sensor mounted on the adapter board).

BlueMotion board installation UM1579

8/26 Doc ID 023744 Rev 1

2 BlueMotion board installation

The software package can be downloaded from the st.com website and includes the

following directory structure:

●

FIRMWARE: it contains the source code of the firmware of the BlueMotion board

together with the corresponding binary file that can be flashed to the board.

The section below describes the procedure for establishing a Bluetooth connection with the

BlueMotion board.

2.1 Establishing Bluetooth connection

A Bluetooth connection to the BlueMotion board can be established in three steps:

searching the BlueMotion device, pairing it and connecting to it. To search the device, open

the “Bluetooth Places” using the Bluetooth software on your PC and click on “Search

Devices“. The BlueMotion board should appear with the name “eMotion BT”, as shown in

Figure 7.

UM1579 BlueMotion board installation

Doc ID 023744 Rev 1 9/26

Figure 7. Searching the BlueMotion board

To pair the device right click on the icon “eMotion BT” and select “Pair”. Enter “1234” in the

“Passkey” field in the dialogue-box (shown in Figure 8) and click “OK”.

AM14729V1

Inhaltsverzeichnis

Andere ST Hauptplatine Handbücher

ST EVAL-L9958 Bedienungsanleitung

ST STMPE821 Bedienungsanleitung

ST EVAL-L9960 Bedienungsanleitung

ST STEVAL-TSP009V2 Administratorhandbuch

ST SPC572LADPT80S Bedienungsanleitung

ST ST9 Series Bedienungsanleitung

ST PractiSPIN UM0696 Bedienungsanleitung

ST L9679E-EVB Bedienungsanleitung

ST SPC572L-DISP Bedienungsanleitung

ST STM32429I-EVAL1 Bedienungsanleitung

ST STM3220G-EVAL Bedienungsanleitung

ST EVALSP320SCPU Bedienungsanleitung

ST EVAL-7803APSO-SA Bedienungsanleitung

ST STR730-EVAL Bedienungsanleitung

ST UM0527 Bedienungsanleitung

ST P-NUCLEO-IOD01A1 Bedienungsanleitung

ST STM32L1 Series Montage- und Bedienungsanleitung

ST M24SR-DISCOVERY Bedienungsanleitung

ST PTB801DC Bedienungsanleitung

ST STEVAL-USBPD45H Administratorhandbuch

ST UM1509 Bedienungsanleitung

ST STEVAL-ISB044V1 Bedienungsanleitung

ST AEK-POW-LDOV01J Bedienungsanleitung

ST EVB-LIV4F Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung