ST SPC572L-DISP Bedienungsanleitung

December 2018 UM2464 Rev 1 1/11

UM2464

User manual

SPC572L-DISP Discovery+ Board

Introduction

This manual provides information for the final user application developer on how to

configure and to use the SPC572L-DISP microcontroller evaluation board.

The discovery board SPC572L-DISP is based on the microcontroller SPC572L64E3, a high

performance 32-bit Power Architecture technology CPU, 1568KB flash in an eTQFP100

package.

The several interfaces including GPIO's, peripherals such as DSPI, LIN, UART, ISO CAN-

FD make the SPC572L-DISP an excellent starter kit for the customer to quickly evaluate the

microcontroller as well as to develop and debug application. An integrated programmer

debugger allows debugging and programming the microcontroller without further tools. The

same circuit allows enabling a USB to serial communication channel (USB Virtual COM

port).

A standard JTAG port allows programming the microcontroller by using different

debug/programmer tools.

www.st.com

Contents UM2464

2/11 UM2464 Rev 1

Contents

1 SPC572L-DISP discovery board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.1 Debug interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.2 I/O interface and connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Hardware description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1 Power supply section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1.1 External Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1.2 USB connection: 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2 Crystal oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.3 Reset section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.4 User LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.5 Integrated USB programmer/debugger and JTAG port . . . . . . . . . . . . . . . 7

2.6 CAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.7 FlexRay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.8 LIN and UART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.9 4x2x25 connector adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

UM2464 Rev 1 3/11

UM2464 List of tables

List of tables

Table 1. PSU section-LEDs description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Table 2. PSU Section-test points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Table 3. User LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Table 4. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

List of figures UM2464

4/11 UM2464 Rev 1

List of figures

Figure 1. SPC572L-DISP board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Figure 2. PSU section - DC input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

UM2464 Rev 1 5/11

UM2464 SPC572L-DISP discovery board

1 SPC572L-DISP discovery board

Figure 1. SPC572L-DISP board

The SPC572L-DISP evaluation kit consists of:

SPC572L-DISP Discovery board (see Figure 1).

USB type A to mini-B cable.

12 V DC power Supply (EU Plug).

All GPIOs and the main signals are accessible by a 4x37 0.1” pin array.

Free ready-to-run application firmware examples are available inside SPC5Studio

(www.st.com/spc5studio) to support quick evaluation and development.

The PCB, the components and all the HW parts assembled in this board meet the

requirements of the applicable RoHS directives.

1.1 Debug interface

14-pin JTAG interface.

USB integrated programmer debugger.

1.2 I/O interface and connectors

PSU plug (+12V).

CAN and LINFlex (Header 2x4 pin).

K-Line and UART (Header 2x4 pin).

Hardware description UM2464

6/11 UM2464 Rev 1

2 Hardware description

2.1 Power supply section

Figure 2. PSU section - DC input

2.1.1 External Power Supply

The external DC supply must be plugged in X2; the switch S1 allows the user to disconnect

the external supply source.

The voltage regulators, U15 and U16 are used to generate 5 V and +3.3V respectively. U14

is a pre-regulator and it must be used when the DC voltage supply is higher than 12 V (i.e.

when the board is used in an application with a DC input higher than 12 V).

The LEDs D7, D9 and D10 are all ON when the board power supply section works properly

and the switch S1 is set to ON position.

2.1.2 USB connection: 3.3 V

If the integrated programmer/debugger is used, 5V from the USB port supplies the board.

U17 and U18 are used to implement an automatic switch.

The VDD_HV_Flex, VDD_HV_JTAG and VDDHV_ADR voltage level is set with the jumper

JP2, JP3 and JP4.

Some test pins are present to monitor the supply voltage levels.

Table 1. PSU section-LEDs description

Item Color Function

D7 Green Vext(+12V)

D9 Green 5V

D10 Green 3.3 V

UM2464 Rev 1 7/11

UM2464 Hardware description

2.2 Crystal oscillator

The external oscillator is connected to a 20MHz crystal (Y2).

2.3 Reset section

U19 drives the reset signal to low level till the VDD_HV_IO level is lower than a fixed level

and it provides a reset pulse when the pushbutton S2 is pressed.

JP21 and JP22 connect the reset signal to the ESR0 and PQRST signal respectively

(default connection: JP21 is closed).

2.4 User LEDs

Three LEDs (D15, D16 and D17) are available for user purposes. The jumpers JP18, JP23

and JP24 allow disconnecting the cathode of each LED's and PE[0], PE[1] and PE[2] can be

used for a different purpose.

2.5 Integrated USB programmer/debugger and JTAG port

The integrated debugger allows the user to program and to debug the software applications.

The integrated tool is based on the UDE PLS software and the device FTDI2232H.

The SPC572L-DISP discovery board includes a full-featured, perpetual code-limited PLS

software license. The debugger serial number is reported on a label applied on the board.

The integrated debugger SW is accessible via SPC5Studio (www.st.com/spc5studio), a

ST's free integrated development environment. To download the debugger software and to

activate the license refer to the PLS website.

Table 2. PSU Section-test points

Test point name Signal/Voltage

TP2 3.3V_USB

TP3 V_Ext (+12V)

TP4 GND

TP5 VPRE

TP6 +5V

TP7 3.3 V

Table 3. User LEDs

LED Color µC Pin - Function

D15 Green PE0

D16 Green PE1

D17 Green PE2

Hardware description UM2464

8/11 UM2464 Rev 1

Some jumpers enable the JTAG port. The board with this setup can be programmed by

using an external programmer. By removing RP1, the integrated programmer is

disconnected and the JTAG port will be enabled to program the microcontroller.

Note: If the USB cable is not used and the board is supplied by using an external DC source, it is

suggested to test the external JTAG programmer before removing the resistor array RP1.

2.6 CAN

U24 is the CAN communication transceiver. Different devices can be assembled:

AMIS30663 or MCP2561 and JP14 must be configured properly considering the transceiver

assembled.

The jumper JP15 connects the termination resistor for CAN bus (120 Ω) while TP14 and

TP15 allow monitoring the output signals CANL and CANH respectively.

The CAN Rx and Tx signals are connected to P4.

2.7 FlexRay

The U23 is the transceiver to manage the FlexRay communication; JP10, JP11 and JP12

allow selection between two channels (FlexRay_0_CA and FlexRay_0_CB). The outputs

are connected to P4, pin 3 and 5; TP12 and TP13 allow monitoring the FlexRay output

signals.

2.8 LIN and UART

The LINFlex supports LIN Master mode, LIN Slave mode and UART mode. JP5 and JP6 are

dedicated to select among LIN_0, LIN_1 and K.

U21 is the transceiver to support the LIN communication, whereas U22 is used to support K-

Line.

The output of these two communication channels is connected to the connector P3.

2.9 4x2x25 connector adapter

This is a female pin array used to connect the main board to a small PCB with the

microcontroller.

UM2464 Rev 1 9/11

UM2464 Appendix

Appendix

The following precautions are recommended when using the SPC572L-DISP:

1. Do not modify or manipulate the board when it is supplied by using the external DC

source or the USB cable.

2. Do not supply the board with AC source.

3. The connectors and cables should be plugged and removed when the board is not

supplied.

4. Please use antistatic tools.

Revision history UM2464

10/11 UM2464 Rev 1

Revision history

Table 4. Document revision history

Date Revision Changes

19-Dec-2018 1 Initial release.

Inhaltsverzeichnis

Andere ST Hauptplatine Handbücher

ST STM32100B-EVAL Bedienungsanleitung

ST UM0804 Bedienungsanleitung

ST STM32H753I-EVAL Bedienungsanleitung

ST EVAL-L9963-MCU Montage- und Bedienungsanleitung

ST SPC582B-DIS Bedienungsanleitung

ST STM32L5 Nucleo-144 board Bedienungsanleitung

ST STM32 Nucleo-64 Bedienungsanleitung

ST NUCLEO-8S207K8 Bedienungsanleitung

ST STUSB02E Bedienungsanleitung

ST STM3210B-EVAL Bedienungsanleitung

ST SPC572LADPT80S Bedienungsanleitung

ST SPC58XXADPT144S REV.B Bedienungsanleitung

ST ST25RU3993 Bedienungsanleitung

ST STM3210B-EVAL Bedienungsanleitung

ST STEVAL-MKI019V1 Bedienungsanleitung

ST EVAL-L99MOD5xXP Bedienungsanleitung

ST STEVAL-IHM011V1 Bedienungsanleitung

ST EVAL-L99H02QF Bedienungsanleitung

ST ST25DV-I2C Bedienungsanleitung

ST STM32CubeH7 Bedienungsanleitung

ST UM2248 Bedienungsanleitung

ST BlueNRG-LP Bedienungsanleitung

ST STEVAL-LLL014V1 Bedienungsanleitung

ST SPC58NHADPT386S Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung