ST STMPE801 Bedienungsanleitung

June 2007 Rev 1 1/17

UM0401

User manual

User manual for eight bit port expander

STMPE801 demonstration board

Introduction

This document explains the functioning of the demo board for the port expander Chip

STMPE801 with a PC GUI for reading and writing to the eight GPIOs and controlling the I2C

interface.

The objective of this demonstration board is to display the capabilities of the 8-bit port

expander (STMPE801) developed by STMicroelectronics using a Windows-based software

application. The software application provides a user-friendly environment to test the port

expander and verify its functionality.

The board is controlled by the GUI through the parallel port in the PC. The power to the

board should come from an external 5 V constant DC power supply.

The PC based GUI acts as the I2C host and controls the STMPE801 slave on the board.

The eight GPIOs in the STMPE801 are accessible through headers and can be easily pulled

high or low using jumpers. The GPIOs can be configured as outputs by writing to the

appropriate registers using the GUI. All these interfaces are controlled by using I2C

communication between Host and Slave devices.

In addition, the hardware has a provision for controlling the STMPE801 through an external

I2C master.

www.st.com

Contents UM0401

2/17

Contents

1 Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.1 System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.3 Software installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.4 Hardware installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.4.1 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.4.2 Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2 Running the STMPE801 port expander GUI . . . . . . . . . . . . . . . . . . . . . . 8

2.1 Running internal registers of STMPE801 . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.2 Programming GPIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.3 Power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.4 Configuring interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3 Using the external I2C master . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4 Demo board footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

5 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

UM0401 List of figures

3/17

List of figures

Figure 1. GUI start up screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Figure 2. Port expander board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Figure 3. Voltage regulation from +5 V supply (VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Figure 4. JP10_1 for Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Figure 5. JP55_2 and JP56_2 for I2C_CLK and I2C_SDATA selection. . . . . . . . . . . . . . . . . . . . . . . . 7

Figure 6. JP2_3 setting for STMPE801 INT pull-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Figure 7. JP3_3 and JP5_3 setting for STMPE801 SCLK and SDAT . . . . . . . . . . . . . . . . . . . . . . . . . 7

Figure 8. JP4_3 setting for STMPE801 I2C Slave address selection . . . . . . . . . . . . . . . . . . . . . . . . . 8

Figure 9. JP6_3 and JP7_3 setting for STMPE801 VCC and VIO connections . . . . . . . . . . . . . . . . . . 8

Figure 10. Screen shot of STMPE801 GUI startup screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Figure 11. Screen shot of write/read tab in STMPE801 GUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Figure 12. Error screen when the incorrect I2C slave address is chosen . . . . . . . . . . . . . . . . . . . . . . 10

Figure 13. GPIO Input state screen shot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Figure 14. GPIO Output state screen shot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Figure 15. Entering in hibernate mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 16. Interrupt setting tab screen shot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 17. Interrupt enabled with indication of current interrupt status in the ISR - screen shot . . . . . 14

Figure 18. External I2C connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 19. Demo board footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Getting started UM0401

4/17

1 Getting started

1.1 System requirements

In order to use the port expander demonstration board with the Windows operating system,

a recent version of Windows, such as Windows XP or Windows 2000 must be installed on

the PC. The user must have administrative rights to install the executable and launch it.

The version of the Windows OS installed on your PC may be determined by clicking on the

"System" icon in the Control Panel.

1.2 Package contents

The port expander demo board includes the following items:

●Hardware content:

– One demonstration board

– One parallel port cable

●Software content:

– PC executable software (STMPE801_GUI) to be used along with demo board

– A DLL file to support the executable (io.dll) to be installed in the same directory as

the executable file.

– Source code (written in Borland Delphi)

●Documentation:

–Usermanual

– Schematic of the hardware

1.3 Software installation

The GUI is a simple executable that can be run even from a USB flash drive. The only

requirement is that the user must have administrative rights on the system in order to open

the accompanying DLL file. The GUI can be started by double-clicking on the file

STMPE801_GUI.exe. When the exe file is opened, the GUI resembles Figure 1 below:

UM0401 Getting started

5/17

Figure 1. GUI start up screen

1.4 Hardware installation

Figure 2 below shows the snapshot of the demonstration board.

Figure 2. Port expander board

Getting started UM0401

6/17

1.4.1 Power supply

The demo board should be powered from an external supply of 5 V, 1 A. (Connector X1 is

for +5 V and Connector X2 is GND). This supply is regulated to get the required VCC, VIO

and Vpull-up voltages by adjusting the Resistor divider components.

Figure 3 below shows the Voltage regulation circuit used. For example, a VCC of 1.8 V can

be achieved by fixing the R6_1 resistor to 680 ohms and calculating R7_1 using the formula:

Equation 1

where, the VOUT we need is 1.8 V, VREF is 1.25 V and IADJ is 50 µA.

By default, the resistors are chosen to fix the voltages at VCC = 1.8 V, VIO = 3.3 V and

Vpull-up = 2.3 V in the demo board.

Figure 3. Voltage regulation from +5 V supply (VIN)

1.4.2 Jumper settings

There are several jumpers on the board that should be properly set to ensure proper

functioning of the board.

●JP10_1: as shown in Figure 4 below, the JP10_1 jumper should be set to power the

voltage Regulators with +5V from the X1 and X2 connectors. This is the main power

connection for all the components on the board.

Figure 4. JP10_1 for Power supply

VOUT VREF

R61

-------------------

⎝⎠

⎛⎞

IADJR71

+= -

UM0401 Getting started

7/17

●JP55_2 and JP56_2: as shown in Figure 5 below, these jumper settings are to select

the I2C CLOCK and DATA source, either from the parallel port (DB-25 connector) or

from an external I2C Master.

Figure 5. JP55_2 and JP56_2 for I2C_CLK and I2C_SDATA selection

These jumpers should be connected if STMPE801 is to be controlled by the GUI through the

DB-25 connector. They can be left open if an external I2C Master is used. For using external

I2C Master, refer to Section 3.

●JP2_3: as shown in Figure 6 below, JP2_3 is used to connect the INT pin to the pull-up

resistor and LED for easier monitoring of the generated interrupts. If this is not

connected, an external pull-up resistor should be used to pull up the open drain INT

output to VIO supply. The jumper should connect pins 1 and 2.

Figure 6. JP2_3 setting for STMPE801 INT pull-up

●JP3_3 and JP5_3: JP3_3 is used to connect the I2C_CLK from the I2C Master to the

STMPE801 SCLK pin. And similarly JP5_3 is used to connect I2C_DATA from the I2C

Master to the STMPE801 SDATA pin. Figure 7 shows the jumper connection to be used

on the board.

Figure 7. JP3_3 and JP5_3 setting for STMPE801 SCLK and SDAT

Running the STMPE801 port expander GUI UM0401

8/17

●JP4_3: JP4_3 is the jumper used to select the I2C slave address as either 0x82 or

0x88. There are pull-down and pull-up resistors for the respective selection and these

can be enabled by shorting the headers as shown in Figure 8.

Figure 8. JP4_3 setting for STMPE801 I2C Slave address selection

●JP6_3 and JP7_3: These jumpers are provided to isolate the STMPE801 chip from the

rest of the board for troubleshooting. They can also be used as test points to measure

the respective supply operating current. To supply the chip with the VCC and VIO, these

jumpers should be shorted as shown in Figure 9.

Figure 9. JP6_3 and JP7_3 setting for STMPE801 VCC and VIO connections

The board is ready to function after these jumper settings and the GPIOs can be accessed

through the different headers provided. Refer to Section 4 for the location of the various

jumpers on the board.

2 Running the STMPE801 port expander GUI

This port expander demo board consists of two main parts:

●PC GUI

●Demonstration board

The various jumpers on the board should be configured correctly before running the GUI.

In order to run the GUI, the demo board must first be connected to the PC with the DB-25

parallel port cable and the power supply of +5 V should be provided.

The user should login as administrator before running the GUI (STMPE801_DEMO.exe).

This file should be run from the same directory as the io.dll file.

When the GUI is successfully running, the startup screen resembles Figure 10. There are

four tab options for testing the various device functionalities as explained in the following

sections.

UM0401 Running the STMPE801 port expander GUI

9/17

Figure 10. Screen shot of STMPE801 GUI startup screen

2.1 Running internal registers of STMPE801

The internal registers of the STMPE801 can be read or written to using the "Write Read" tab

in the GUI. Figure 11 shows a screen shot of this function. The radio button device 1 should

be selected if the slave address is 0x82, and radio button device 2 should be selected if the

slave address is 0x88. Making the wrong selection on the device radio buttons generates an

error message as shown in Figure 12.

Running the STMPE801 port expander GUI UM0401

10/17

Figure 11. Screen shot of write/read tab in STMPE801 GUI

The register contents can be read by writing the 8-bit hex address into the "Address" field

and the number of registers to be read in the "Length" field. Then click on the "Read" button.

The contents displayed are in Hex and 8-bits wide. The same procedure can be followed for

writing into the registers. The content to be written should be in bytes and only 8 bytes can

be written with a single "Write" button click.

Note: The Length field should always be non-zero. A read or write with length zero causes the GUI

to close.

Figure 12. Error screen when the incorrect I2C slave address is chosen

Inhaltsverzeichnis

Andere ST Hauptplatine Handbücher

ST STEVAL-WESU1 Bedienungsanleitung

ST STEVAL-IFS001V1 Bedienungsanleitung

ST EVAL-L99DZ200 Bedienungsanleitung

ST EVALSP1340CPU Bedienungsanleitung

ST UM1682 Bedienungsanleitung

ST STEVAL-PCC001V1 Bedienungsanleitung

ST STEVAL-ISB044V1 Bedienungsanleitung

ST STM3241G-EVAL Bedienungsanleitung

ST UM1509 Bedienungsanleitung

ST NUCLEO-WB15CC Bedienungsanleitung

ST STM32G081B-EVAL Bedienungsanleitung

ST STM32F407 Series Bedienungsanleitung

ST UM0704 Bedienungsanleitung

ST EVALKITSTKNX Bedienungsanleitung

ST STM32L152RCT6 Discovery kit Bedienungsanleitung

ST STEVAL-SPIN3202 Bedienungsanleitung

ST SPC572LADPT100S Bedienungsanleitung

ST UM1935 Bedienungsanleitung

ST EVALST-3PHISOSD Bedienungsanleitung

ST UM0920 Bedienungsanleitung

ST STEVAL-IPMnM1S Bedienungsanleitung

ST STM3240G-EVAL Bedienungsanleitung

ST X-NUCLEO-NFC03A1 Bedienungsanleitung

ST FDA803S Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung