ST X-NUCLEO-IDB05A1 Bedienungsanleitung

July 2015

DocID028033 Rev 1

1/16

www.st.com

UM1912

User manual

Getting started with X-NUCLEO-IDB05A1 BLE expansion board

based on the SPBTLE-RF module for STM32 Nucleo

Introduction

The X-NUCLEO-IDB05A1 is a Bluetooth Low Energy evaluation board based on BlueNRG-MS RF

module, SPBTLE-RF, to allow expansion of the STM32 Nucleo boards. The SPBTLE-RF module is FCC

(FCC ID: S9NSPBTLERF) and IC certified (IC: 8976C-SPBTLERF). The BlueNRG-MS is a very low

power Bluetooth Low Energy (BLE) single-mode network processor, compliant with Bluetooth

specification v4.1. X-NUCLEO-IDB05A1 is compatible with the ST Morpho and Arduino UNO R3

connector layout.

This expansion board can be plugged into the Arduino UNO R3 connectors of any STM32 Nucleo

board. The user can mount the ST Morpho connectors if required. The different expansion boards can

be easily stacked to allow evaluation of different devices with Bluetooth Low Energy connectivity.

The board has the following features:

On-board SPBTLE-RF module based on the BlueNRG-MS single mode BLE network processor

SPI EEPROM for parameter saving

Jumper at 3V3 for checking the current consumption of STM32 expansion board

Figure 1: Bluetooth Low Energy expansion board based on SPBTLE-RF module for STM32 Nucleo

Contents

UM1912

2/16

DocID028033 Rev 1

Contents

1Getting started................................................................................3

1.1 Hardware requirements....................................................................3

1.2 System requirements.......................................................................3

1.3 Setting up the board.........................................................................4

2Hardware description.....................................................................5

2.1 X-NUCLEO-IDB05A1 board.............................................................5

2.2 SPI and GPIO connection options....................................................6

2.3 Current measurement......................................................................7

2.4 X-NUCLEO-IDB05A1 component placement...................................7

3Component description .................................................................8

3.1 SPBTLE-RF module.........................................................................8

3.2 SPI EEPROM...................................................................................8

4Formal notices required by the U.S. Federal Communications

Commission ("FCC") ..............................................................................9

5Formal notices required by the Industry Canada ("IC") ............10

6Hardware schematic diagrams....................................................11

7Bill of material...............................................................................13

8Revision history ...........................................................................15

UM1912

Getting started

DocID028033 Rev 1

3/16

1 Getting started

This section describes the hardware requirements for the X-NUCLEO-IDB05A1 evaluation

board.

1.1 Hardware requirements

The X-NUCLEO-IDB05A1 is an expansion board for use with STM32 Nucleo boards. To

function correctly, the X-NUCLEO-IDB05A1 must be connected to the STM32 Nucleo

board as shown in Figure 2: "X-NUCLEO-IDB05A1 plugged into an STM32 Nucleo board

through the Arduino UNO R3 connector" below.

The STM32 Nucleo firmware and related documentation is available at

http://www.st.com/stm32nucleo

Figure 2: X-NUCLEO-IDB05A1 plugged into an STM32 Nucleo board through the Arduino UNO

R3 connector

The interconnection between the STM32 Nucleo and the X-NUCLEO-IDB05A1 has been

designed to permit the use of any STM32 Nucleo board, although complete testing has

been performed using the NUCLEO-L053R8 hosting the ultra-low power STM32, and the

NUCLEO-F401RE hosting the dynamic efficiency STM32.

1.2 System requirements

Using the Nucleo boards with the X-NUCLEO-IDB05A1 expansion board requires the

following software and hardware:

Windows PC (XP, Vista, 7, 8) to install the firmware package

USB type A to Mini-B USB cable to connect the Nucleo board to the PC

Installation of the board firmware package (order code: X-CUBE-BLE1) and the BlueNRG

graphical user interface utility on the user's PC requires the following:

Getting started

UM1912

4/16

DocID028033 Rev 1

128 MB of RAM

40 MB of hard disk space

The X-CUBE-BLE1 firmware and related documentation is available on www.st.com

1.3 Setting up the board

To set up the board, perform the following steps:

1. Check that the jumper on the J1 connector is connected. This jumper provides the

required voltage to the devices on the board

2. Connect the X-NUCLEO-IDB05A1 on the Nucleo board from the top as shown in

Figure 2: "X-NUCLEO-IDB05A1 plugged into an STM32 Nucleo board through the

Arduino UNO R3 connector"

3. Power the Nucleo board using the Mini-B USB cable

4. Program the firmware in the STM32 on the Nucleo board using the firmware example

provided

5. Reset the MCU board using the reset button available on the Nucleo board

6. The evaluation kit is ready to be used

UM1912

Hardware description

DocID028033 Rev 1

5/16

2 Hardware description

This section describes the X-NUCLEO-IDB05A1 features and provides information which

could be useful to understand the board schematic diagrams.

2.1 X-NUCLEO-IDB05A1 board

The board allows the user to test the functionality of the SPBTLE-RF module. The

SPBTLE-RF hosts the BlueNRG-MS, a very low power Bluetooth Low Energy (BLE) single-

mode network processor, compliant with Bluetooth specification v4.1. The module also

embeds the innovative BALF-NRG-01D3 (balun with integrated harmonic filter) and a chip

antenna.

Its functionality can be exploited using the firmware package contained in the X-CUBE-

BLE1. It is fundamental to program the microcontroller on the STM32 Nucleo board. Please

refer to user manuals UM1724 and UM1725, available on www.st.com.

The SPBTLE-RF module and the STM32 Nucleo board are connected through connectors

CN5, CN6, CN8 and CN9 (see Table 1: "Interconnection between STM32 Nucleo board

and X-NUCLEO-IDB05A1 left-side connectors" for details). The pins indicated with an

asterisk (*) allow an alternative pin for that specific function, i.e. SPI_IRQ could be moved

from CN8.1 to CN5.2.

Table 1: Interconnection between STM32 Nucleo board and X-NUCLEO-IDB05A1 left-side

connectors

Signal

Name

IOREF

RESET

3V3

GND

VIN

Left connector

Connector

Name

CN6 Power

CN8 Analog

Pin#

NUCLEO-L053R8

(MCU Port)

PA0

PA1

PA4

PB0

PC1/ PB9

PC0/ PB8

X-NUCLEO-IDB05A1

expansion board

3V3

GND

SPI_IRQ (*)

SPI_CSN (*)

Hardware description

UM1912

6/16

DocID028033 Rev 1

Table 2: Interconnection between STM32 Nucleo board and X-NUCLEO-IDB05A1 right-side

connectors

Signal

Name

D15

D14

AREF

GND

D13

D12

D11

D10

Right connector

Connector

Name

CN5 Digital

CN9 Digital

Pin#

NUCLEO-L053R8

(MCU Port)

PB8

PB9

PA5

PA6

PA7

PB6

PC7

PA9

PA8

PB10

PB4

PB5

PB3

PA10

PA2

PA3

X-NUCLEO-IDB05A1

expansion board

GND

SPI_CLK (Opt)

SPI_MISO

SPI_MOSI

SPI_CSN (Opt)

SPI_IRQ (Opt)

SPI_EEPROM_nS

BlueNRG_RST

SPI_CLK (*)

Opt = Optional connection.

2.2 SPI and GPIO connection options

Table 3: "BlueNRG-MS interface (optional) with the STM32 Nucleo board" shows the SPI

and GPIO connection options between the STM32 and BlueNRG-MS hosted on the

SPBTLE-RF module. These can be used for operation of the board in different

configurations in cases where different expansion boards are utilized and there is a conflict

of signals.

Table 3: BlueNRG-MS interface (optional) with the STM32 Nucleo board

BlueNRG-MS

Signal

SPBTLE-RF

Default

STM32

port

Optional STM32

port

BlueNRG-MS_IRQ

4 –SPI_IRQ

PA0

PC7

To use optional connection

mount R8, demount R1

UM1912

Hardware description

DocID028033 Rev 1

7/16

BlueNRG-MS

Signal

SPBTLE-RF

Default

STM32

port

Optional STM32

port

BlueNRG-MS_CSn

10 –SPI_CS

PA1

PB6

To use optional connection

mount R7, demount R2

BlueNRG-MS_SCLK

7 –SPI_CLK

PB3

PA5

To use optional connection

mount R6, demount R4

Refer to the schematic diagrams for details.

For the optional connections, modify the firmware for the correct use of the STM32

resources to be used.

2.3 Current measurement

To monitor the power consumption of the BlueNRG-MS X-NUCLEO-IDB05A1 board, insert

an ammeter probe between pins 1 and 2 of the jumper on the J1 connector. Since the

power consumption of BlueNRG-MS is very low during most of its operating time, an

accurate instrument in the range of a few µA may be required.

2.4 X-NUCLEO-IDB05A1 component placement

The following diagram shows the component placement on the X-NUCLEO-IDB05A1

board.

Figure 3: X-NUCLEO-IDB05A1 component placement details

Component description

UM1912

8/16

DocID028033 Rev 1

3 Component description

The board has the following devices.

3.1 SPBTLE-RF module

The SPBTLE-RF is an easy-to-use Bluetooth Low Energy module. It is based on the

BlueNRG-MS device, which is a very low power Bluetooth Low Energy (BLE) single-mode

network processor, compliant with Bluetooth specification v4.1. The SPBTLE-RF has the

following certifications:

FCC (FCC ID: S9NSPBTLERF)

IC (IC: 8976C-SPBTLERF)

The interface of the device to the STM32 Nucleo boards is through SPI interface and

GPIOs.

The SPBTLE-RF integrates a balun BALF-NRG-01D3 and a chip antenna. It embeds 32

MHz and 32.768 kHz crystal oscillators for the BlueNRG-MS.

The part numbers used to develop this application are shown in Table 4: "SPBTLE-RF

details".

Table 4: SPBTLE-RF details

Feature

Description

Sales type

SPBTLE-RF

Package

SMD 11 pin

Operating voltage

2 to 3.6 V

3.2 SPI EEPROM

The M95640-R is a 64 Kbit serial SPI bus EEPROM with high-speed clock interface. The

device can be used to store the configuration parameters related to applications or settings

of the SPBTLE-RF module

The part numbers used to develop this application are shown in Table 5: "SPI EEPROM

details".

Table 5: SPI EEPROM details

Feature

Description

Sales type

M95640-RMC6TG

Package

MLP8

Operating voltage

1.8 to 5.5 V

UM1912

Formal notices required by the U.S. Federal

Communications Commission ("FCC")

DocID028033 Rev 1

9/16

4 Formal notices required by the U.S. Federal

Communications Commission ("FCC")

Any changes or modifications to this equipment not expressly approved by

STMicroelectronics may cause harmful interference and void the user's authority to operate

this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including any interference that may cause undesired

operation.

This device uses, generates and radiated radio frequency energy. The radio frequency

energy produced by this device is well below the maximum exposure allows by Federal

Communications Commission (FCC).

The X-NUCLEO-IDB05A1 contains FCC certified module SPBTLE-RF (FCC ID:

S9NSPBTLERF).

Formal notices required by the Industry Canada

("IC")

UM1912

10/16

DocID028033 Rev 1

5 Formal notices required by the Industry Canada

("IC")

English:

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is

subject to the following two conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference that may cause undesired

operation of the device.

French:

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils

radio exempts de licence. 'exploitation est autorisée aux deux conditions suivantes: (1)

l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter

tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en

compromettre le fonctionnement.

The X-NUCLEO-IDB05A1 contains IC certified module SPBTLE-RF (IC: 8976C-

SPBTLERF).

Andere Handbücher für X-NUCLEO-IDB05A1

Inhaltsverzeichnis

Andere ST Hauptplatine Handbücher

ST STEVAL-IHM011V1 Bedienungsanleitung

ST STEVAL-ISB68WA Bedienungsanleitung

ST STEVAL-LVLP01 Bedienungsanleitung

ST STEVAL-IHM020V1 Bedienungsanleitung

ST Teseo-VIC3DA Bedienungsanleitung

ST UM0527 Bedienungsanleitung

ST SPC584B-DISP Bedienungsanleitung

ST TN100 RF Bedienungsanleitung

ST STM3221G-EVAL Bedienungsanleitung

ST STMPE801 Bedienungsanleitung

ST User Manual Bedienungsanleitung

ST STM32F4 Series Montage- und Bedienungsanleitung

ST L9678-S-EVB Bedienungsanleitung

ST STEVAL-AETKT2V1 Bedienungsanleitung

ST STEVAL-DIGAFEV1 Bedienungsanleitung

ST STM32H743I-EVAL Bedienungsanleitung

ST EVALST-3PHISOSD Bedienungsanleitung

ST M24LR64-R Bedienungsanleitung

ST STM32F103RET6 Bedienungsanleitung

ST STM32756G-EVAL Bedienungsanleitung

ST UM2335 Bedienungsanleitung

ST STEVAL-IME015V1 Bedienungsanleitung

ST EVALSP820-XS Bedienungsanleitung

ST EVAL-L99ASC03 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung