Standa 11SOLO2 Bedienungsanleitung

SINGLE CHANNEL LASER POWER/ENERGY METER

11SOLO2

INSTRUCTION MANUAL

Revision –0.9

June 2008

11SOLO2 User’s Manual Revision 0.9 1

WARRANTY

The Standa 11SOLO2 Single Channel Laser Power, Energy and Power/Energy Meter carries a one-year

warranty (from date of shipment) against material and/or workmanship defects, when used under normal

operating conditions. The warranty does not cover damages related to battery leakage or misuse.

|Standa will repair or replace, optionally, any 11SOLO2 that proves to be defective during the warranty

period, except in the case of product misuse.

Any attempt by an unauthorized person to alter or repair the product voids the warranty.

The manufacturer is not liable for consequential damages of any kind.

Customers must fill in and mail the warranty card in order to activate the warranty.

In case of malfunction, contact your local Standa distributor or nearest Standa office to obtain a return

authorization number. The material should be returned to:

STANDA

Švitrigailos 4-39

03222 Vilnius

Lithuania

Tel: +370-5-2651474

Fax: +370-5-2651483

e-mail: [email protected]

Website: www.standa.lt

CLAIMS

To obtain warranty service, contact your nearest Standa agent or send the product, with a description of

the problem, transportation and insurance prepaid, to the nearest Standa agent. Standa assumes no risk

for the damage in transit. Standa will, at its option, repair or replace the defective product free of charge

or refund your purchase price. However, if Standa determines that the failure is caused by misuse,

alterations, accident or abnormal condition of operation or handling, you will be billed for the repair and

the repaired product will be returned to you, transportation prepaid.

11SOLO2 User’s Manual Revision 0.9 2

SAFETY INFORMATION

Do not use the 11SOLO2 if the device or the detector looks damaged, or if you suspect that the

11SOLO2 is not operating properly.

Appropriate installation must be done for water-cooled and fan-cooled detectors. Refer to the specific

instructions for more information. The user must wait for a while before handling these detectors after

power is applied. Surfaces of the detectors get very hot and there is a risk of injury if they are not allowed

to cool down.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and

on, it is suggested to try to correct the interference by taking one or more of the

following steps:

• Reorient or relocate the receiving antenna.

• Increase the distance between the equipment and receiver.

• Connect the equipment to an outlet that is on a different circuit than the receiver.

• Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved in writing by Standa may void the

user’s authority to operate this equipment.

SYMBOLS

The following international symbols are used in this manual:

Refer to the manual for specific Warning or Caution information to avoid any damage to

the product.

DC, Direct Current

11SOLO2 User’s Manual Revision 0.9 3

1.1 INTRODUCTION.............................................................................................................................................6

1.2 SPECIFICATIONS ...........................................................................................................................................7

1.3 FRONT PANEL DESCRIPTION.........................................................................................................................9

1.4 TOP PANEL DESCRIPTION ...........................................................................................................................10

2.1 HOW TO USE THE KEYS TO ACCESS THE MENUS...........................................................................................12

2.2 QUICK POWER AND ENERGY MEASUREMENT PROCEDURE...........................................................................13

2.3 DESCRIPTION OF THE TOP LEVEL 11SOLO2 MENUS ...................................................................................16

2.3.1 Displays.............................................................................................................................................16

2.3.1.1 Real time display ...........................................................................................................................16

2.3.1.2 Histogram display..........................................................................................................................17

2.3.1.3 Line Plot display............................................................................................................................17

2.3.1.4 Statistics display ............................................................................................................................18

2.3.1.5 Peak Power Display.......................................................................................................................18

2.3.1.6 Status display.................................................................................................................................19

2.3.1.7 Avg Display...................................................................................................................................19

2.3.1.8 View File .......................................................................................................................................20

2.3.1.9 Fluence Display.............................................................................................................................20

2.3.1.10 Zoom..........................................................................................................................................20

2.3.1.11 Digital Tuning Needle display...................................................................................................21

2.3.2 Scale Menu ........................................................................................................................................21

2.3.3 Settings...............................................................................................................................................22

2.3.3.1 Wavelength Setting........................................................................................................................22

2.3.3.2 Corrections Setting ........................................................................................................................23

2.3.3.3 Data Sampling Settings..................................................................................................................24

2.3.3.4 Trig Level Setting..........................................................................................................................29

2.3.3.5 Period Multiplier............................................................................................................................29

2.3.3.6 Refer Values ..................................................................................................................................29

2.3.3.7 Save and Load User Settings.........................................................................................................30

2.3.3.8 Power Unit.....................................................................................................................................31

2.3.3.9 Communication..............................................................................................................................31

2.3.3.10 Fluence.......................................................................................................................................31

2.3.3.11 Peak Power ................................................................................................................................31

2.4 REAL-TIME CONTROLS AND ABOUT 11SOLO2..........................................................................................31

2.4.1 Control Functions in the Ctrl menu...................................................................................................32

2.4.1.1 Ctrl – Zero Offset...........................................................................................................................32

2.4.1.2 Ctrl - Acquire Data ........................................................................................................................32

2.4.1.3 Ctrl - Transfer File.........................................................................................................................32

2.4.1.4 Ctrl – Statistics Mode ....................................................................................................................33

2.4.1.5 Ctrl – Relative Mode .....................................................................................................................33

2.4.1.6 Ctrl – Energy Mode.......................................................................................................................34

2.4.1.7 Ctrl - Analog OUT.........................................................................................................................34

2.4.1.8 Ctrl - Anticipation..........................................................................................................................35

2.4.1.9 Ctrl – Display Hi Res.....................................................................................................................35

2.4.1.10 Ctrl – View Data........................................................................................................................35

2.4.2 “?”.....................................................................................................................................................35

2.5 SERVICE .....................................................................................................................................................35

3.1 INSTALLATION............................................................................................................................................36

3.1.1 Installation for Windows™: ..............................................................................................................36

3.2 SETTING UP COMMUNICATION TO THE 11SOLO2.......................................................................................36

3.2.1 Verify COM Port................................................................................................................................36

3.2.2 Connect to the 11SOLO2...................................................................................................................36

3.2.3 To echo commands ............................................................................................................................37

3.2.4 Test the connection............................................................................................................................37

3.2.5 HyperTerminal settings shortcut .......................................................................................................37

3.3 PCSOLO USER-FRIENDLY SERIAL DATA ACQUISITION SOFTWARE .............................................................37

3.4 TRADITIONAL COMMUNICATION SETTINGS................................................................................................38

11SOLO2 User’s Manual Revision 0.9 4

3.4.1 Serial Command format.....................................................................................................................38

3.4.1.1 Serial Protocol Rules:....................................................................................................................38

3.4.1.2 Text mode rules:............................................................................................................................38

3.4.1.3 Binary Mode rules:........................................................................................................................39

3.4.2 Serial Command Directory................................................................................................................41

3.4.3 Serial commands................................................................................................................................42

3.4.4 ERROR MESSAGES..........................................................................................................................60

4.1 USB INSTALLATION FOR THE SOLO2 ........................................................................................................61

4.2 FREE SOFTWARE UPGRADE ........................................................................................................................61

4.3 BATTERY CHARGING..................................................................................................................................61

QEA AND QEAS............................................................................................................................ 62

5.1 QEA/12/25/50 AND QEAS/12/25/50 .........................................................................................................62

ATTENUATOR/DIFFUSER CALIBRATION PROCEDURE................................. 62

6APPENDIX B ..................................................................................................................................... 64

6.1 RECYCLING AND SEPARATION PROCEDURE.................................................................................................64

6.2 SEPARATION:..............................................................................................................................................64

6.3 DISMANTLING PROCEDURE:........................................................................................................................64

11SOLO2 User’s Manual Revision 0.9 5 
LIST OF ILLUSTRATIONS 
 
FIG. 1-1 11SOLO2 FRONT PANEL................................................................................................................. 9 
FIG. 1-2 11SOLO2 TOP PANEL................................................................................................................... 10 
FIG. 2-1 THE MENU BAR............................................................................................................................... 13 
FIG. 2-2 THE DIALOG BOX ............................................................................................................................ 13 
FIG. 2-3 VIEW OF THE FIRST GROUP OF 11SOLO2 MENUS............................................................................ 16 
FIG. 2-4 REAL TIME DISPLAY ....................................................................................................................... 17 
FIG. 2-5 DISPLAY OPTIONS MENU ................................................................................................................ 17 
FIG. 2-6 STATISTICS DISPLAY....................................................................................................................... 18 
FIG. 2-7 STATUS DISPLAY ............................................................................................................................ 19 
FIG. 2-8 WATTMETER DATA SAMPLING MENU ............................................................................................... 19 
FIG. 2-9 VIEW FILE SCREEN......................................................................................................................... 20 
FIG. 2-8 DIGITAL NEEDLE DISPLAY............................................................................................................... 21 
FIG. 2-10 SCALE MENU................................................................................................................................21
FIG. 2-11 SETTINGS MENU........................................................................................................................... 22 
FIG. 2.12 SETTING CORRECTION MENU ........................................................................................................ 23 
FIG. 2-13 DATA SAMPLING PARAMETERS WINDOW........................................................................................ 26 
FIG. 2-14 PASS/FAIL MENU......................................................................................................................... 30 
FIG. 2-15 PULSE WIDTH SETTING FOR THE PEAK POWER MODE ................................................................... 31 
FIG. 2-16 VIEW OF THE MENU STRUCTURE................................................................................................... 32 
 
 Standa Ltd. All rights reserved 

11SOLO2 User’s Manual Revision 0.9 6

1 THE 11SOLO2 SINGLE CHANNEL LASER POWER/ENERGY METER

1.1 Introduction

To obtain the full performance from the 11SOLO2, we recommend that you read this manual carefully.

The 11SOLO2 is a microprocessor-based power and energy meter that uses the latest technology to

provide a multitude of options in a user-friendly environment. It is a complete power and energy meter.

The 11SOLO2 provide a statistical analysis of your measurements. It allows you to store data on the 1-

megabyte flash internal memory. Moreover, the 11SOLO2 can be updated over the internet by

connecting the USB or the RS-232 port to a personal computer.

The 11SOLO2 has enhanced network capabilities that take further advantage of the USB and RS-232

ports for data acquisition and remote control. It can transfer data files to a PC for more sophisticated data

analysis and respond to commands through the PC interface. You will find an easy-to-use

communications software to transform your PC screen into a virtual 11SOLO2 on our website.

There is no need to enter the head specifications when connecting the new Standa power or energy

detector heads, for heads version 4 and above. The 11SOLO2 is already internally set up to accept all

the Standa wattmeter and joulemeter heads with a DB-15 connector. When connecting a 11QE-xx-x-MT

or a 11XLE-4 the 11SOLO2 enters in the metallic mode to ensure proper measurements. The metallic

mode is available on all 11SOLO2. The new 11SOLO2 also has improved performance in joulemeter

mode that allows 2 additional lower scales.

Although the default parameter is Watt, you may also choose to measure in dBm.

dBm = Log (power in Watts/0.001W)

Unpacking

Each Standa 11SOLO2 is thoroughly tested and calibrated prior to shipment.

Visually inspect every 11SOLO2 unit after removing it from the shipping containers. If you see any

damage, retain all packaging materials and shipping receipts. Any damage claim should be made

promptly to the transportation company. Notify the nearest Standa representative concerning the claim,

so that any repair or replacement can be arranged as soon as possible.

Easy software upgrade

Keep in touch with the latest improvements to our user-friendly software. You can download the latest

software version anytime from our website www.standa.lt and install it on the 11SOLO2 with the serial

interface. You will find all the necessary information on downloading and upgrading in section 4.2.

11SOLO2 User’s Manual Revision 0.9 7

1.2 Specifications

The following specifications are based on a one-year calibration cycle, an operating temperature of 18 to

28ºC (64 to 82ºF) and a relative humidity not exceeding 80%.

Table 1-1 List of Specifications

Power meter specifications 11SOLO2

Power Range 0.1 nW to 10 kW

Power Scales

(photo diode head)

3nW, 10nW, 30nW, 100nW, 300nW, 1µW, 3µW, 10µW, 30µW, 100µW,

300µW, 1mW, 3mW, 10mW, 30mW, 100mW, 300mW, 1W, 3W

Power Scales

(thermal head)

16 scales: 300uW, 1mW, 3mW, 10mW, 30mW, 100mW, 300mW, 1W,

3W, 10W, 30W, 100W, 300W, 1kW, 3kW, 10kW

Resolution (digital) Current scale/2048

Monitor Accuracy ±0.5 % 5 µV full scale1

Response Time

(accelerated)2

1 sec

Sampling Frequency 200 kHz

Statistics Current value, Max, Min, Average, Std Dev., RMS stability, PTP stability,

Time

Energy meter specifications 11SOLO2

Energy Range 0.1µJ to 20 kJ

Energy Scales 20 scales: 10uJ, 30uJ, 100µJ, 300µJ, 1mJ, 3mJ, 10mJ, 30mJ, 100mJ,

300mJ, 1J, 3J, 10J, 30J, 100J, 300J, 1kJ, 3kJ, 10kJ, 30kJ

Resolution (digital) 5 nJ

Accuracy31.0 %50 µV < 500 Hz

2.0 %50 µV 500 Hz to 1.2 kHz

3%50 µV 1.2 kHz to 6 kHz (MT mode)

6%50 µV 6kHz to 10 kHz (MT mode)

Default Trigger Level 2 %

Software Trigger

Level

0.1% to 99.9%, 0.1% resolution

Metallic mode: hardware set to 3%.

1The 5µV bias can introduce an error into low power measurements with low sensitivity detectors. It is

essential to use the Zero Offset to rezero the 11SOLO2 before making a measurement in these

conditions. It is always good practice to use the Zero Offset. See section 2.2.

2Varies with detector head.

3Including linearity, detector dependant.

11SOLO2 User’s Manual Revision 0.9 8

Repetition Frequency 3 kHz in acquire data, no missing point

2 kHz in statistics mode, no missing point

3-10 kHz in acquire data, with data sampling at a pulse rate of 3 kHz4.

Statistics Current value, Max, Min, Average, Std Dev., RMS stability, PTP stability,

Pulse #, Repetition Rate, Avg Power.

Data Storage 225,000 points5

General Specifications 11SOLO2

Digital Display 76.78 x 57.58 mm LCD, 240 x 160 Pixels

Display Rate 3 Hz numeric display

15 Hz bar graph & needle display

Bar Graph 165 divisions

Data Displays Real time, Line plot, Histogram, Statistics, Digital tuning needle

User input correction

factors

2 multipliers and 2 offsets (7 digits floating point)

Analog Output 0 – 1 volt, full scale, ± 1%

Internet Upgrades USB and RS-2326

PC Serial Commands USB and RS-2325

High throughput

serial frequency

Up to 200Hz, with a 310 ms delay between burst for Metallic or XLE

joulemeters, whereas 45 to 78 ms for MB joulemeter and power heads.

Dimensions (without

stand)

210 mm(W) x 122 mm (H) x 44 mm (D)

Weight (with stand) 0.52 kg

Battery Pack 4 rechargeable 1.2 V Ni-MH AA

Battery life 11 hours, 6 hours with backlight

Battery charge time 6 hours

Universal External

Power Supply

Input: 100/240 VAC 50-60 Hz, Output 9 VDC 1.66 A.

4Above 3 kHz the monitor will sample points but no log every single point.

5Maximum if not using any advanced features that require memory.

6USB cable included. RS-232 cable must be purchased separately.

11SOLO2 User’s Manual Revision 0.9 9

Fig. 1-1 11SOLO2 Front Panel

1.3 Front Panel Description

1- I/O and backlight control key.

The I/O key has two functions:

a. 11SOLO2 on and off

Pressing the I/O key quickly when the 11SOLO2 is OFF turns the 11SOLO2 ON (do not

hold the I/O key). To turn off the 11SOLO2, press and hold the I/O key a few seconds.

To prevent battery leakage and to increase battery life, we recommend switching off the

11SOLO2 when not in use.

b. Backlight control

With 11SOLO2 ON, pressing the I/O key very quickly switches the LCD screen Backlight

ON or OFF. If you are working without the external power supply, turn the backlight off

for longer battery life.

2- , , , Arrow keys.

a. The Arrow keys allow the user to browse through the menus. Press the Right Arrow

key until you reach your desired option. To go backwards, keep pressing the Left Arrow

key

b. When you are not in the Menu, the Arrow keys permits alternative function for quick

access button

UP key: Make a physique scale up and the auto-scale is disabled.

Down key: Make a physical scale down and the auto-scale is disabled.

Left key: Makes or remakes a zero offset.

Right key: Activate the custom wavelength keypad.

3- ENTER key.

The ENTER key selects the highlighted option.

4- Menu Key

The Menu key gives access to the MENU BAR.

5- LCD SCREEN

Inhaltsverzeichnis

Andere Standa Messgerät Handbücher

Standa

Standa 11UNO Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung