Stanley FATMAX FMHT82565-0 Bedienungsanleitung

kMΩ

INSTRUCTION MANUAL

Basic DMM

www.2helpU.com

WARNING: To reduce the risk of injury, read and

understand these safety warnings and instructions before

using the light. Keep these instructions with the light for future

reference. If you have questions or comments, contact us.

FMHT82565-0

M A X

MIN

HOLD

200k

20k

2k 200

1.5V

200

600

200

200m

20m

kMΩ

Introduction

The instrument of this series is a small hand-held 3 1/2

digital multimeter. Stable, highly reliable and anti-drop per-

formance. It is provided with a LCD display of 15 mm height

for clear reading. The circuit design takes LSI double integral

A/D converter as its core under the protection of an overload

protection circuit, making it a superior and handy instrument.

It can be used to measure DC and AC voltage, DC current,

resistance, battery voltage, diodes and forin-circuit continuity

test.

Measurement features of the types of this

series:

Features

Alternating Voltage measurement V~

Direct Voltage measurement

Direct current measurement

Resistance measurement Ω

Diode measurement

On-off measurement

Battery measurement 1.5V

Data hold

User Manual

FRONT PANEL

1 Display

3 1/2 digital LCD

display.

2 Function and range

switch

Select different functions

and range.

3 VΩmA Jack

4 COM Jack

5 10A Jack

6 Data hold button

Press the HOLD button.

The LCD will hold the last

reading measured and

display the H symbol.

When the button is

released, the instrument

will return to normal.

MAX

MIN

HOL D

200k

20k

200

1.5V

200

600

200

200m

20m

kMΩ

Safety Information

FMHT82565-0 Digital Multimeter is designed based on EN

61010-1, EN 61010-2-030, EN 61010-2-033, 600V CAT III

and pollution degree 2.

WARNING

The special attention should be paid when using the meter because

the improper usage may cause electric shock and damage the

meter. The safety measures in common safety regulations and

operating instruction should be complied with when using. In order

to make fully use of its functions and ensure safe operations please

comply with the usage in this section carefully.

Safety Signs

Important safety information. Read the manual.

High voltage with danger.

Ground.

Double Insulation (Class II safety equipment).

Fuse must be replaced as per the specification herein.

Accord with the related EU laws and regulations

AC (Alternating Current)

DC (Direct Current)

Conforms to UL STD. 61010-1, 61010-2-030, 61010-2-

033; Certified to CSA STD C22.2 NO. 61010-1, 61010-2-

030, 61010-2-033

Notice

• The instrument can only be used in conjunction with the probe for the

compliance with safety standards. If the probe needs replacing due

to damage, the replacement must be of the same type or the same

electrical specifications.

User Manual

• Do not exceed the input limits specified for each range.

• When the instrument is measuring, do not touch the input

terminal not in use.

• When a measurement range is uncertain, turn the function/

range switch to the maximum range position.

• Before turning the function/range switch, make sure the probe

is open with the circuit being measured.

• Before on-line resistance measurement, turn off all power and

discharge all capacitors.

• Be careful when taking measurement of voltage higher than

60V DC/30V AC. Remember to keep your fingers behind the

hand shield of the probe.

• When measuring a TV set or switch power supply, watch for

pulse in the circuit that may damage the multimeter.

• Measure known voltage with the meter to verify that the meter

is working properly. If the meter is working abnormally, stop

using it immediately A protective device may be damaged.

If there is any doubt, please have the meter inspected by a

qualified technician.

• Before taking the measurement of voltage with the probe,

make sure there is no electronic element connected to the test

socket of the transistor.

Maintenance

• Before removing the rear cover, disconnect the probe from the

circuit to be measured.

• To protect the internal circuit, replace the fuse with one of the

same specification:

F1:FF 10AH 600V, 10KA; F2:FF 400mAH 600V, 10KA

• Don’t use the instrument until the rear cover is placed back

and the screws are tightened.

• Clean the housing of instrument only with a wet rag dripped

with little detergent but never chemical solution.

• In case of any abnormality, stop using it and sent it for

maintenance.

Accuracy Indicators

Accuracy:±(% of reading+digits) with one year of warranty.

Reference conditions: environmental temperature is from

18°C~28°C, relative humidity is not more than 80%.

General features:

Safety Class CAT III 600V

waterproof IP20

Fuse

F1:FF 10AH 600V,10KA;

F2:FF 400mA H 600V, 10KA

Power AAA 1.5V × 2 batteries

Maximum display value 1999

Over-range indication “OL”

Polarity display “–” for negative polarity

Low voltage indication “ ” on the display

Operating temperature 0~40°C(32~104°F)

Storage temperature -10~50°C(14~122°F)

Relative humidity <80% RH

Altitude <2000m

Dimension (L×W×H) 150×74×48mm

Weight about 220g

User Manual

Direct voltage measurement

Range Resolution Accuracy

200mV 100μV ±0.5% of reading, ±3 digits

1mV ±0.5% of reading, ±3 digits

20V 10mV ±0.5% of reading, ±3 digits

200V 100mV ±0.5% of reading, ±3 digits

600V 1V ±0.8% of reading, ±5 digits

Overload protection:

200mV range: 250V DC or RMS. AC

The rest range: 600V DC or RMS. AC

Alternating voltage measurement

Range Resolution Accuracy

200V 100mV ±1.0% of reading, ±10 digits

600V

1V ±1.2% of reading, ±10 digits

Overload protection: 600V DC or RMS. AC

Frequency range: 40Hz to 400Hz

Display: Average (effective value of sinusoid)

Direct current measurement

Range Resolution Accuracy

2mA 1μA ±1 % of reading, ±3 digits

20mA

10μA ±1 % of reading, ±5 digits

200mA 100μA ±1.5% of reading, ±5 digits

10A 10mA ±3% of reading, ±10 digits

Overload protection:

F1:FF 10AH 600V, 10KA; F2:FF 400mAH 600V, 10KA

When measured current is greater than 2A, the continuous measure-

ment time cannot be more than 2 minutes. Disconnect the current

and wait 10 minutes before making another measurement.

Resistor

Range Resolution Accuracy

200Ω 0.1Ω ±1.2% of reading, ±5 digits

2kΩ

1Ω ±0.8% of reading, ±2 digits

20kΩ 10Ω ±0.8% of reading, ±2 digits

200kΩ 100Ω ±0.8% of reading, ±2 digits

2MΩ 1kΩ ±1.0% of reading, ±5 digits

Maximum open circuit voltage: 2.4V

Overload protection: 250V DC or RMS. AC

Diode and circuit on-off measurement

Range Description

When the on-resistance is smaller than 30Ω,

the built-in buzzer will beep.

Displays the approximate diode positive voltage.

Overload protection: 250V DC or RMS. AC

Battery voltage measurement

Position Resolution Load impedance

1.5V 0.001V 470

0.01V 3000

Overload protection: F2:FF 400mA H 600V,10KA

Operating Instructions

Notices before operation:

1 Plug the instrument in, check the batteries, if it is low, the

symbol “ ” will display, requiring battery replacement;

otherwise follow the steps below.

User Manual

2 The “ ” besides the probe jack indicates that the input

voltage or current should not exceed the specified limits

to protect the internal circuit.

3 Before measurement, turn the function/range switch to

the desired range.

Direct voltage measurement

1 Insert the red probe into the “VΩmA” jack and the black

one into the “COM” jack.

2 Turn the function/range switch to “ ” and connect the

probe to the power supply or load to be measured. The

polarity touched by the red probe will be on the display.

WARNING

1. If you do not know the measured voltage range in advance,

set the function/range switch to the maximum range, and then

gradually turn to smaller ranges until satisfactory resolution.

2. If the display shows “OL”, this indicates an overrange

measurement, and the switch should be set to a higher range.

3. Do not input a voltage of more than 600V, it is capable of

indicating a higher voltage, but with the risk of damaging the

inside circuit.

4. When taking the measurement of high voltage, pay special

attention to avoid an electric shock.

Alternating voltage measurement

1 Place the red probe into the “VΩmA” jack and the black

one into the “COM” jack.

2 Turn the function/range switch to “v~” and connect the

probe to the power supply or load to be measured.

Note: Refer to point 1, 2, 3, and 4 for direct voltage

measurement.

Direct current measurement

1 Place the black probe into the “COM” jack. for current to be

measured not exceeding 200mA, put the red one into the

“VΩmA” jack. For current to be measured between 200mA and

10A, insert the red probe into the “10A” jack.

2 Set the function/range switch to the desired “ ” range, and

connect the probe in series with the load to be measured. The

current value and the polarity connected to the red probe will be

shown on the display.

WARNING

1. If you do not know the measured current range in advance, set the function/

range switch to the maximum range, and then gradually turn to smaller

ranges until satisfactory resolution.

2. If the display shows “OL”, this indicates an overrange measurement, and the

switch should be set to a higher range.

3. The symbol “ ” beside the probe indicates the maximum input current

is 200mA or 10A, depending on the inserted jack Overcurrent will blow the

fuse.

1 Place the black probe into the “COM” jack and the red one into

the “VΩmA” jack.

2 Turn the function/range switch to the “COM” jack, and connect

the probe to the resistor being measured and read the results on

the display.

WARNING

1. If the resistor being measured is greater than the maximum value of the

selected range, the display will show “OL”, requiring the selection of a higher

range. It normally takes a few seconds for the reading to get stable when

measuring a resistor larger than 1 MΩ.

2. In default of input, for instance, open circuit, the display shows “OL”.

3. When measuring an online resistor, de-energized the circuit being measured

and discharge all capacitors.

User Manual

Inhaltsverzeichnis

Sprachen:

Andere Stanley Messgerät Handbücher

Stanley

Stanley STHT77341 Bedienungsanleitung

Stanley

Stanley STHT77100 Bedienungsanleitung

Stanley

Stanley TLM 220 Bedienungsanleitung

Stanley

Stanley Fatmax TLM330S Bedienungsanleitung

Stanley

Stanley SLL360 Bedienungsanleitung

Stanley

Stanley STHT77366 Bedienungsanleitung

Stanley

Stanley STHT77498-1 Bedienungsanleitung

Stanley

Stanley FATMAX FMHT77585 Bedienungsanleitung

Stanley

Stanley STHT77502-1 Bedienungsanleitung

Stanley

Stanley STHT77498 Bedienungsanleitung

Stanley

Stanley TLM 130i Bedienungsanleitung

Stanley

Stanley STHT1-77032 Bedienungsanleitung

Stanley

Stanley STHT77616 Bedienungsanleitung

Stanley

Stanley STHT77366 Bedienungsanleitung

Stanley

Stanley TLM99 Bedienungsanleitung

Stanley

Stanley STHT77065 Bedienungsanleitung

Stanley

Stanley FATMAX FMHT77595 Bedienungsanleitung

Stanley

Stanley TLM65 Bedienungsanleitung

Stanley

Stanley TLM99 Bedienungsanleitung

Stanley

Stanley Fatmax TLM165S Bedienungsanleitung

Stanley

Stanley FATMAX FMHT77596 Bedienungsanleitung

Stanley

Stanley TLM65 Handbuch

Stanley

Stanley Compulevel Bedienungsanleitung

Stanley

Stanley FCL-G Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung