Stanley 204018 Bedienungsanleitung

Filename: “Panic Hardware Exit Device Installation”

Location: Date Created: 8/16/2004

Issued By: PCN 04-132 Date Revised: 12/3/2004

Revised By: M. Sheehan Page 1 of 6

Panic Hardware Exit Device

Installation Manual

Quick-Reference Guide

204018

Rev. A, 12-3-04

Prohibition on Copying

Any unauthorized reproduction, disclosure or distribution of copies by any person

of any portion of this work may be a violation of copyright law of the United

States of America and other countries, could result in the awarding of statutory

damages of up to $250,000 (17 USC 504) for infringement, and may result in

Stanley Access Technologies

Quick-Reference Guide

Filename: “Panic Hardware Exit Device Installation”

Location: Date Created: 8/16/2004

Issued By: PCN 04-132 Date Revised: 12/3/2004

Revised By: M. Sheehan Page 2 of 6

1. Lay SX panel horizontally with escutcheon and cylinder lock facing

down.

2. Install screw #6-32 x 2” into the center block to aid in pulling and

holding the center block in position.

3. Remove Dummy Plate from center block. Be sure to save the two #10-

32 x 3/4” flat head machine screws holding Dummy Plate, as you will

need them for later installation.

4. Locate the center block in the rectangular hole.

5. Align the protruding square of the center block with the square hole in

the mounting plate and place onto the center block. (See Fig. 5.)

6. Place scissor cartridge on center block and secure with the two #10-32

x 3/4” flat head machine screws. (See Fig. 6)

Filename: “Panic Hardware Exit Device Installation”

Location: Date Created: 8/16/2004

Issued By: PCN 04-132 Date Revised: 12/3/2004

Revised By: M. Sheehan Page 3 of 6

7. Secure Crank arm.

a. Remove the #6-32 x 2” helper screw.

b. Align crank arm with shaft. You may have to operate the push

bar scissors to align tab with slot.

c. Secure with one #6-32 x 1/4” truss head. (See Fig. 7)

8. Insert push bar (See Fig. 9) and secure end caps with four #10-32 x

1/2” self-tapping screws. (See Fig. 10)

9. Center Panic bar assembly on mutton bar. Measure six inches down

from end of panic bar. (End opposite to center block) Drill .218” hole

centered through panic hardware and mutton bar. Secure hardware

down with ¼-20 x 1” self-tapping hex head bolt.

Filename: “Panic Hardware Exit Device Installation”

Location: Date Created: 8/16/2004

Issued By: PCN 04-132 Date Revised: 12/3/2004

Revised By: M. Sheehan Page 4 of 6

10.Insert cover strip into back bar. Push in until flush with back bar

extension. (See Fig. 11)

11.Install base caps and secure with four #10-32 x 2” self-tapping screws.

(See Fig.12)

Filename: “Panic Hardware Exit Device Installation”

Location: Date Created: 8/16/2004

Issued By: PCN 04-132 Date Revised: 12/3/2004

Revised By: M. Sheehan Page 5 of 6

12.Adjust bottom throw bolt length.

a. Remove the four #10-32 flat head screws from the guide block in

the bottom of the stile

b. Rotate the bottom throw bolt counterclockwise until it sticks out

5/8” from the bottom of the stile.

c. Replace guide block and four #10-32 flat head screws.

13.Check operations.

a. Fully depress push bar and release

b. Top bolt will retract and latch.

BOTTOM

THROW

BOLT

GUIDE

BLOCK

MOUNTING

SCREWS

Filename: “Panic Hardware Exit Device Installation”

Location: Date Created: 8/16/2004

Issued By: PCN 04-132 Date Revised: 12/3/2004

Revised By: M. Sheehan Page 6 of 6

c. Push the jamb sensor in and you should see about 5/8” of

movement from the top bolt.

Inhaltsverzeichnis

Andere Stanley Werkzeuge Handbücher

Stanley

Stanley EZM4000 Fehlerbehebungshandbuch

Stanley

Stanley CH15 Bedienungsanleitung

Stanley

Stanley S32 Bedienungsanleitung

Stanley

Stanley MasterFix XGrip N09QI Bedienungsanleitung

Stanley

Stanley 160173XSTN Bedienungsanleitung

Stanley

Stanley 150 Bedienungsanleitung

Stanley

Stanley 9045670STN Bedienungsanleitung

Stanley

Stanley SFP 1250 Bedienungsanleitung

Stanley

Stanley 07536 Fehlerbehebungshandbuch

Stanley

Stanley HP Twin 8 Bedienungsanleitung

Stanley

Stanley SST1801 Bedienungsanleitung

Stanley

Stanley AL24 Bedienungsanleitung

Stanley

Stanley BXGT10147E Montage- und Bedienungsanleitung

Stanley

Stanley CH1513101 Bedienungsanleitung

Stanley

Stanley BR87 Bedienungsanleitung

Stanley

Stanley DR19 Bedienungsanleitung

Stanley

Stanley TR201 Bedienungsanleitung

Stanley

Stanley Kit 6 Bedienungsanleitung

Stanley

Stanley 71501 Fehlerbehebungshandbuch

Stanley

Stanley 55 Bedienungsanleitung

Stanley

Stanley STHM5 Bedienungsanleitung

Stanley

Stanley GD50 Bedienungsanleitung

Stanley

Stanley STHT82942 Bedienungsanleitung

Stanley

Stanley Bostitch T55 Series Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

Grizzly

Grizzly H6472 Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung