Stanley BXGT10147E Montage- und Bedienungsanleitung
Automatic.Hose.Reel.
Installation, Use, and
Maintenance Guide
Unpacking
Please.check.the.contents.of.your.package
A, Instruction.Manual
B, Hardware.Pack
C, Hose.Reel
D, Wall.Bracket
E, Mount tube
Caution: This.hose.reel.is.not.intended.to
be.used.as.a.potable.water.source
Caution: Except.as.indicated.in.these
instruction.do.not.open.the.outer.housing
Hardware.Pack
Contents
Couplings
Your hose reel was made with one of
The following hose-end configurations
Poly quick-connect
with nozzle
Preparing.your.tools
Installation.is.easier.with.the.right.tools…
electric drill
3/8”masonry drill bit
1/8”drill bit
pen or pencil
bubble level
adjustable wrench
Philips screwdriver
tape measure
B.1 X 4
Choosing the best location
Select the best location to mount your hose reel
1, Near your worksite. Your hose reel comes with up to 10-30m (30-100ft) of
hose, Think about where you need to water and make sure the hose can reach.
2. Near a spigot. This hose reel is provided with a 1-2m (3-6.5ft) leader hose, so
selection a location close to the spigot
3. On a sturdy wall or structure. There are many options for mounting this hose
reel into various structures, but it’s important that the structure be sturdy enough
to support the weight of the reel, up to 14.5kg(32lbs) with water
4. In the shade. By mounting your hose reel in a shady area of your yard, you
can reduce harmful effects of sunlight on the reel and hose and extend the life of
your purchase.
Installation:Heavy plywood cladding
If you wall’s ply wood cladding is thick, 12mm (1/2”) or more, you can directly
mount the Wall Bracket
WARNING: Ensure there are no live electrical wires or
Plumbing in the wall at the location you are drilling
CAUTION: when using powder tools such as a
electric drill, please wear eye protection.
‘
READING: please check which mold you have, and then
get the installation dimension from the table below.
1, The mounting bracket has 4 holes which will be used to secure it to the wall or timber
post. Use the mounting bracket as a template to mark the holes prior to drilling (Note: Use
a level to ensure the holes are vertically aligned).
2, Drill the required holes with a 10mm(3/8”) masonry drill bit (for wall mount)
approximately 50mm(2)”deep or a 3mm(1/0") drill bit (for timber post) approximately
60mm(2.5") deep.
3, Once the holes are drilled, insert the anchor plug (provided) into each hole (applicable
for wall mount).
4, Fasten the mounting bracket with four screws and washer (provided .B.1 or B.2) to the
wall or timber post
5, Hag Hose Reel (C) on wall bracket (D), and secure it by inserting the mount
tube.(provided E)
6, Connect the leader hose to water source.
Model number
A
B
Hardware pack
BXGT10147E
57mm(2-1/4”)
165mm(6-1/2”)
B.1
Operating Instructions
Extending the hose
1, Pull the hose out to the desired length. The hose will automatically lock in position
Anywhere lock: Pull out the hose to the desired length and then stop pulling so the reel can lock in the desired position.
2, To retract, pull out about 300mm of hose; the hose will retract back into the reel
Caution: Always hold the hose until it
completely. retract into the hose reel
Caution: The yellow tape marks the end
of the hose length.
Noted :
1, To retract, it is suggested that a minimum of 15”has been extended
2, During retraction, always hold on to the hose and follow the retraction until it is finished. Under no circumstances should
you let go of the hose as it will retract at a high speed potentially causing injury to any person standing nearby, and/or
damaging to the hose and hose reel.
3, When the hose is twisted, it is necessary to extend the hose to its full length, untwist the hose and then allow it to retract
Adjusting the stop-ball
The location of the stop ball can be adjusted to allow more or less hose exposed when fully rewound.
1, Pull out the hose to the desired length, ensuring the hose reel is locked ( will not rewind).
2, Loose two screws in the stop ball and move it to the desired location.
3, And tight screws in the desired location.
4, Unlock the hose
Caution: Always make sure the hose reel is locked before removing the stop ball, and make
sure the stop-ball is securely fastened before unlocking the reel.
Care and Maintenance Tips
1, Turn off the water source and release the pressure in the hose when not in use.
2, To prevent freezing and potential damage to the hose reel, store indoors during winter months.
4, Clean the housing and hose using only mild soap and water.
Inhaltsverzeichnis
Andere Stanley Werkzeuge Handbücher
Stanley
Stanley 55 Betriebsanleitung
Stanley
Stanley MasterFix XGrip N09QI Bedienungsanleitung
Stanley
Stanley S32 Bedienungsanleitung
Stanley
Stanley Bostitch T55 Series Bedienungsanleitung
Stanley
Stanley 55 Bedienungsanleitung
Stanley
Stanley STHT82942 Bedienungsanleitung
Stanley
Stanley DR19 Bedienungsanleitung
Stanley
Stanley 70500 Fehlerbehebungshandbuch
Stanley
Stanley Kit 6 Bedienungsanleitung
Stanley
Stanley STHM5 Bedienungsanleitung
Stanley
Stanley EZM4000 Fehlerbehebungshandbuch
Stanley
Stanley HSX Series Bedienungsanleitung
Stanley
Stanley STEL501 Bedienungsanleitung
Stanley
Stanley RINGER9/16 Bedienungsanleitung
Stanley
Stanley 07536 Fehlerbehebungshandbuch
Stanley
Stanley SST1801 Bedienungsanleitung
Stanley
Stanley 8221074STN Series Bedienungsanleitung
Stanley
Stanley CH15 Bedienungsanleitung
Stanley
Stanley SFP 1250 Bedienungsanleitung
Stanley
Stanley BR Series Bedienungsanleitung
