Star Micronics FuturePRNT TSP100 Bedienungsanleitung

Hardware Manual

Federal Communications Commission

Radio Frequency Interference

Statement

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

For compliance with the Federal Noise Interference Standard, this equipment requires a

shielded cable.

This statement will be applied only for the printers marketed in U.S.A.

Statement of

The Canadian Department of Communications

Radio Interference Regulations

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital

apparatus set out in the Radio Interference Regulations of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le

brouillage radioélectrique édicté par le ministère des Communications du Canada.

The above statement applies only to printers marketed in Canada.

Manufacturer’s Declaration of Conformity

EC Council Directive 89/336/EEC of 3 May 1989

This product, has been designed and manufactured in accordance with the International

Standards EN 61000-6-3 / 2001 and EN 55024 / 1998, following the provisions of the

Electro Magnetic Compatibility Directive of the European Communities as of May 1989.

EC Council Directive 73/23/EEC and 93/68/EEC of 22 July 1993

This product, has been designed and manufactured in accordance with the International

Standards EN 60950-1, following the provisions of the Low Voltage Directive of the

European Communities as of 2001.

The above statement applies only to printers marketed in EU.

Trademark acknowledgments

TSP100: Star Micronics Co., Ltd.

Notice

without STAR’s express permission is forbidden.

•The contents of this manual are subject to change without notice.

•All efforts have been made to ensure the accuracy of the contents of this manual at the

time of going to press. However, should any errors be detected, STAR would greatly

appreciate being informed of them.

•The above notwithstanding, STAR can assume no responsibility for any errors in this

manual.

TABLE OF CONTENTS

1. Unpacking and Installation ..........................................................................1

1-1.Unpacking ...........................................................................................1

2. Parts Identification and Nomenclature ......................................................2

3. Setup...............................................................................................................5

3-1.Connecting the USB Cable to the Printer ............................................5

3-2.Connecting to a Peripheral Unit ..........................................................6

3-3.Loading the Roll Paper ........................................................................7

3-4.Connecting the USB Cable to the PC ................................................10

3-5.Installing the Printer Software ...........................................................10

3-6.Connecting the Power Cord ..............................................................11

3-7.Turning Power On .............................................................................12

4. Attaching the Accessories...........................................................................13

4-1.Attaching the Holder Plate ................................................................13

4-2.Attaching the Rubber Feet .................................................................14

4-3.Switch Blind Installation ................................................................... 15

5. Termal Roll Paper Specification ...............................................................16

6. Control Panel and Other Functions ..........................................................17

6-1.Control Panel .....................................................................................17

6-2.Errors .................................................................................................17

6-3.Self-Printing ......................................................................................19

7. Preventing and Clearing Paper Jams ....................................................... 20

7-1.Preventing Paper Jams.......................................................................20

7-2.Removing Paper Jam .........................................................................20

7-3.Releasing a Locked Cutter (Auto Cutter Mode only) .......................21

8. Periodical Cleaning .....................................................................................23

8-1.Cleaning the Thermal Head ...............................................................23

8-2.Cleaning the Paper Holder ................................................................23

9. Periheral Unit Drive Circuit ...................................................................... 24

10. Specifications ............................................................................................... 26

10-1.General Specifications .......................................................................26

10-2.Auto Cutter Specifications ................................................................27

10-3.Interface .............................................................................................27

10-4.Electrical Characteristics ...................................................................27

10-5.Environmental Requirements ............................................................27

10-6.Reliability ..........................................................................................28

Please access the following URL

http://www.star-m.jp/eng/dl/dl02.htm

for the lastest revision of the manual.

– 1 –

1-1. Unpacking

After unpacking the unit, check that all the necessary accessories are included in

the package.

Fig. 1-1 Unpacking

If anything is missing, contact the dealer where you bought the printer and ask

them to supply the missing part. Note that it is a good idea to keep the original box

and all the packing materials just in case you need to pack the printer up again and

send it somewhere at a later date.

1. Unpacking and Installation

Printer

Paper roll holder

Holder plate

Switch blind

USB cable

Power cord

Rubber

foots

CD-ROM

Setup sheet

Roll paper

Screws

Ferrite core

–2 –

2. Parts Identification and Nomenclature

Cover open lever

Pull this lever in the

direction of the

arrow to open the

printer cover.

Control panel

Features LED indica-

tors to indicate printer

status and switches to

operate the printer.

Power switch

Used to turn on/off

power to the printer.

Power connector

For connection of

the power cord.

Peripheral drive connector

Connects to peripheral

units such as cash

drawers, etc.

Do not connect this to a

telephone.

Interface connector

For connection to a

host computer.

Printer cover

Open this cover to load or

replace paper.

Auto Cutter Model

–3 –

Tear Bar Model

Cover open lever

Pull this lever in the

direction of the

arrow to open the

printer cover.

Power connector

For connection of

the power cord.

Peripheral drive connector

Connects to peripheral

units such as cash

drawers, etc.

Do not connect this to a

telephone.

Interface connector

For connection to a

host computer.

Printer cover

Open this cover to load or

replace paper.

Control panel

Features LED indica-

tors to indicate printer

status and switches to

operate the printer.

Power switch

Used to turn on/off

power to the printer.

–4 –

Choosing a place for the printer

Before actually unpacking the printer, you should take a few minutes to

think about where you plan to use it. Remember the following points

when doing this.

✓Choose a firm, level surface where the printer will not be exposed to

vibration.

✓The power outlet you plan to connect to for power should be nearby

and unobstructed.

✓Make sure that the printer is close enough to your host computer for

you to connect the two.

✓Make sure that the printer is not exposed to direct sunlight.

✓Make sure that the printer is well away from heaters and other sources

of extreme heat.

✓Make sure that the surrounding area is clean, dry, and free of dust.

✓Make sure that the printer is connected to a reliable power outlet. It

should not be on the same electric circuit as copiers, refrigerators, or

other appliances that cause power spikes.

✓Make sure that the room where you are using the printer is not too

humid.

WARNING

✓Shut down your equipment immediately if it produces smoke, a

strange odor, or unusual noise. Immediately unplug the equipment

and contact your dealer for advice.

✓Never attempt to repair this product yourself. Improper repair work

can be dangerous.

✓Never disassemble or modify this product. Tampering with this

product may result in injury, fire, or electric shock.

–5 –

3. Setup

3-1. Connecting the USB Cable to the Printer

Affix the ferrite core onto the USB interface cable and pass the cable through the

cable support as shown. Then, connect the USB interface cable to the printer.

Note: The dialog shown below may appear on your PC screen if your PC is

running Windows 98 or Me, and if you turn ON the power of the printer

for the first time while the PC and the printer are connected with the

USB cable. In this case, refer to the software manual on the CD-ROM,

in the following directory: Documents folder.

–6 –

3-2. Connecting to a Peripheral Unit

You can connect a peripheral unit to the printer using a modular plug. The

following describes how to install the ferrite core and make the actual connection.

See “Modular plug”on page 24 for details about the type of modular plug that is

required. Note that this printer does not come with a modular plug or wire, so it

is up to you to obtain one that suits your needs.

CAUTION

Make sure that the printer is turned off and unplugged from the AC outlet

and that the computer is turned off before making connections.

(1) Connect the peripheral drive cable to the connector on the rear panel of the

printer.

CAUTION

Do not connect a telephone line into the peripheral drive connector.

Failure to observe this may result in damage to the printer.

Also, for safety purposes, do not connect wiring to the external drive

connector if there is a chance it may carry peripheral voltage.

–7 –

3-3. Loading the Roll Paper

Be sure to use roll paper that matches the printer’s specification.

When using a paper roll with an 57.5 mm width, install the paper roll holder as

described on the following page.

1) Push the cover open lever, and open

the printer cover.

2) While observing the direction of the

roll, set the paper roll into the hol-

low, and pull on the leading edge of

the paper toward you.

Cover open lever

Roll paper

Andere Handbücher für futurePRNT TSP100

Inhaltsverzeichnis

Andere Star Micronics Drucker Handbücher

Star Micronics

Star Micronics SP500 Series Bedienungsanleitung

Star Micronics

Star Micronics TSP800 Series Bedienungsanleitung

Star Micronics

Star Micronics TSP650 Series Bedienungsanleitung

Star Micronics

Star Micronics SM-L300 Kurzanleitung

Star Micronics

Star Micronics SP300 Series Bedienungsanleitung

Star Micronics

Star Micronics TSP600 Series Bedienungsanleitung

Star Micronics

Star Micronics LC-7211 Bedienungsanleitung

Star Micronics

Star Micronics NP-215 Bedienungsanleitung

Star Micronics

Star Micronics TUP592 Bedienungsanleitung

Star Micronics

Star Micronics NX-2450 Bedienungsanleitung

Star Micronics

Star Micronics 8 Series Gebrauchsanweisung

Star Micronics

Star Micronics NX-1040 Bedienungsanleitung

Star Micronics

Star Micronics TSP800 Series Bedienungsanleitung

Star Micronics

Star Micronics Multi-Font LC-IOII Bedienungsanleitung

Star Micronics

Star Micronics 4111 Gebrauchsanweisung

Star Micronics

Star Micronics NX-1001 Bedienungsanleitung

Star Micronics

Star Micronics SP500 Series Benutzerhandbuch

Star Micronics

Star Micronics NX-100 Bedienungsanleitung

Star Micronics

Star Micronics SP500 Series Betriebsanleitung

Star Micronics

Star Micronics SF-10HA Bedienungsanleitung

Star Micronics

Star Micronics DP8340 Series Bedienungsanleitung

Star Micronics

Star Micronics NP-IO Bedienungsanleitung

Star Micronics

Star Micronics SP2000 Bedienungs- und Wartungshandbuch

Star Micronics

Star Micronics TSP2000 Series Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung

Star Micronics futurePRNT TSP100 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken