Star Micronics SP2000 Bedienungsanleitung

DOT MATRIX PRINTER

SP2000 SERIES

USER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

MANUALE DI ISTRUZIONI

Federal Communications Commission

Radio Frequency Interference

Statement

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

For compliance with the Federal Noise Interference Standard, this equipment requires a

shielded cable.

This statement will be applied only for the printers marketed in U.S.A.

Statement of

The Canadian Department of Communications

Radio Interference Regulations

This digital apparatus does not exceed the Class A limits for radio noise emissions from

digital apparatus set out in the Radio Interference Regulations of the Canadian Department

of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le

brouillage radioélectrique édicté par le ministère des Communications du Canada.

The above statement applies only to printers marketed in Canada.

Manufacturer’s Declaration of Conformity

EC Council Directive 89/336/EEC of 3 May 1989

This product, has been designed and manufactured in accordance with the International

Standards EN 50081-1/01.92 and EN 50082-1/01.92, following the provisions of the

ElectroMagneticCompatibilityDirectiveoftheEuropeanCommunitiesasofMay1989.

EC Council Directive 73/23/EEC and 93/68/EEC of 22 July 1993

This product, has been designed and manufactured in accordance with the International

Standards EN 60950, following the provisions of the Low Voltage Directive of the

European Communities as of July 1993.

The above statement applies only to printers marketed in EU.

Trademark acknowledgments

SP2000 Series: Star Micronics Co. Ltd.

ESC/POS: Seiko Epson Corporation

Notice

without STAR’s express permission is forbidden.

•The contents of this manual are subject to change without notice.

•All efforts have been made to ensure the accuracy of the contents of this manual at the

time of going to press. However, should any errors be detected, STAR would greatly

appreciate being informed of them.

•The above notwithstanding, STAR can assume no responsibility for any errors in this

manual.

TABLE OF CONTENTS

1. Outline ...............................................................................................................1

2. Unpacking and Installation................................................................................2

2-1. Unpacking ..............................................................................................2

2-2. Locating the Printer................................................................................3

2-3. Handling Care ........................................................................................3

2-4. Maintenance ...........................................................................................3

3. Parts Identification and Nomenclature ..............................................................4

4. Optional AC Adapter.........................................................................................6

5. Connecting.........................................................................................................8

5-1. Ferrite Core Installation .........................................................................8

5-2. Connecting to host computer (serial interface) ......................................9

5-3. Connecting to host computer (parallel interface).................................10

5-4. Connecting to a Peripheral Unit...........................................................10

6. Loading the Ribbon Cartridge and Paper ........................................................12

6-1. SP2300 type .........................................................................................12

6-2. SP2500 type .........................................................................................15

6-3. Removing the Paper .............................................................................20

7. Control Panel ...................................................................................................21

7-1. Basic Operation....................................................................................21

7-2. Errors ...................................................................................................22

7-3. Switch Operation (Combined Switch Operation) ................................23

8. Control Codes ..................................................................................................27

8-1. Star Mode Commands .........................................................................27

8-2. ESC/POS Mode Commands ................................................................32

9. Optional Near-end Sensor ...............................................................................35

9-1. Adjusting the Near-end Sensor ............................................................35

Appendix A: General Specifications .................................................................151

Power Supply Specifications......................................................................154

Appendix B: Serial Interface .............................................................................155

B-1. Pins and Signal Names ......................................................................155

B-2. Interface Connections (Serial Interface) ............................................156

Appendix C: Parallel Interface ..........................................................................157

C-1. Table of Connection Signals for Each Mode .....................................157

Appendix D: DIP Switch Setting ......................................................................159

D-1. Parallel Interface ................................................................................159

D-2. Serial Interface ...................................................................................161

Appendix E: Memory Switch Settings ..............................................................164

Appendix F: Peripheral Unit Driver Circuit.....................................................165

– 1 –

ENGLISH

The SP2000 Series Serial Impact Dot Matrix Printer is designed for use with

electronic instruments such as POS, banking equipment, computer peripheral

equipment, etc.

The major features of the SP2000 series are as follows:

1. Bi-directional printing at approx. 3.1 lines/sec.

2. Serial interface or parallel interface.

3. The data buffer allows the unit to receive print data even during printing.

4. Peripheral unit drive circuit enables control of external devices such as cash

drawers.

SP2 3 2 0 M D 42 – 24

No. of print columns

42 : 42 columns (16 CPI)

Interface

D : Serial interface (RS-232C)

C : Parallel interface

Paper feed

M : Friction paper feed method

Mechanism

2 : Singlecolor,42columns(16CPI)

6 : Twocolor,42columns(16CPI)

Printer type

3 : Standard type

5 : Auto cutter equipped type

SP2000 series printer

1. Outline

– 2 –

ENGLISH

2. Unpacking and Installation

2-1. Unpacking

After unpacking the unit, check that all the necessary accessories are included in

the package.

SP2300 type

SP2500 type

Fig. 2-1 Unpacking

If anything is missing, contact the dealer where you bought the printer and ask

themtosupplythemissingpart.Notethatitisagoodideatokeeptheoriginalbox

andallthepackingmaterialsjustincaseyouneedtopacktheprinterupagainand

send it somewhere at a later date.

Printer Ribbon cartridge

User’s manual

Ferrite core Fasteners

Printer

Ribbon cartridge

User’s manual

Ferrite core Fasteners

– 3 –

ENGLISH

2-2. Locating the Printer

When you locate your printer, keep the following tips in mind:

1. Protectyourprinterfromexcessiveheatsuchasdirectsunlightorheaters,and

keep it away from moisture and dust.

2. Place the printer on a firm, level surface which is fairly vibration-free.

3. Asteadypowersupplythatisnotsubjecttopowersurgesshouldbeconnected

to the printer.

For example, do not connect it to the same circuit as a large, noise-producing

appliance such as a refrigerator or an air conditioner.

4. Make sure the line voltage is the voltage specified on the printer’s identifica-

tion plate.

5. Todisconnecttheprinter,theplughastobedisconnectedfromthewallsocket,

which has to be located close to the printer, and easy to access.

2-3. Handling Care

1. Be careful not to drop paper clips, pins or other foreign matter into the unit as

these cause the printer to malfunction.

2. Do not attempt to print when either paper or ribbon cartridge is not located in

the printer, otherwise the print head can be damaged.

3. Do not open the cover while printing.

4. Do not touch the print head immediately after printing as it gets very hot.

5. Use only roll paper that is not glued to the core.

6. When the paper end mark appears on the paper, replace the roll paper before

it runs out.

2-4. Maintenance

Essentially,yourprinterisarobustpieceofequipment,butshouldbetreatedwith

a modicum of care in order to avoid malfunctions. For example:

1. Keep your printer in a “comfortable” environment. Roughly speaking, if you

feel comfortable, then the environment is suitable for your printer.

2. Do not subject the printer to physical shocks or excessive vibration.

3. Avoid over-dusty environments. Dust is the enemy of all precision mechani-

cal devices.

4. To clean the exterior of the printer, use a cloth barely dampened with either

water with a little detergent or a little alcohol, but do not allow any liquid to

fall inside the printer.

5. The interior of the printer may be cleaned with a small cleaner or a com-

pressed-air aerosol (sold for this purpose). When performing this operation,

be sure not to bend or damage any cable connections or electronic compo-

nents.

– 4 –

ENGLISH

3. Parts Identification and Nomenclature

SP2300 type

Fig. 3-1 External view of the printer (SP2300 type)

Cover

Protects the printer from dust and reduces noise.

Do not open the cover while printing.

Control panel

Features two control switches and

two indicators to indicate printer

status.

AC adapter

Refer to the following

section for installation

instructions.

Interface connector

Connects the printer with

host computer.

Peripheral unit drive circuit

connector

Connects to peripheral units

such as cash drawers, etc.

Do not connect this to a

telephone.

DIP switch

Use to make various

settings.

Power switch

Turns printer power on

and off.

– 5 –

ENGLISH

SP2500 type

Fig. 3-2 External view of the printer (SP2500 type)

Cover

Protects the printer from dust and reduces noise.

Do not open the cover while printing.

Control panel

Features two control switches and two

indicators to indicate printer status.

AC adapter

Refer to the following

section for installation

instructions.

Interface connector

Connects the printer with

host computer.

Peripheral unit drive circuit

connector

Connects to peripheral units

such as cash drawers, etc.

Do not connect this to a

telephone.

DIP switch

Use to make various

settings.

Power switch

Turns printer power on

and off.

– 6 –

ENGLISH

4. Optional AC Adapter

Use the following procedure to install the optional AC adapter.

Fig. 4-2 Flat side faces this way

1Turn the printer over.

2Plug the AC adapter’s cord into the socket as shown in the above illustration.

Make sure the flat side of the plug is facing towards the inside of the printer.

3Use one of the nylon fasteners that comes with the printer to fasten the cord

at the point indicated in the illustration.

AC adapter Adapter holder Fasteners

AC adapter cord Cord holder

[Before AC adaptor installed] [After AC adaptor installed]

Fig. 4-1

AC adaptor Screws

Fastener

Adaptor holder

Cord holder

Power code

– 7 –

ENGLISH

4Coil the AC adapter cord into the space provided, and insert the AC adapter

into its space.

5UsetheadapterholderandscrewtosecuretheACadapterandthecordholder

and screw to secure the cord.

6Turn the printer back right side up.

7Plug the female end of the power cord into the AC adapter, and plug the other

end into a power outlet.

Fig. 4-3 Fasten cord here

Andere Handbücher für SP2000

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Star Micronics Drucker Handbücher

Star Micronics

Star Micronics NX-2420 Multi-Font Bedienungsanleitung

Star Micronics

Star Micronics NX-10 Bedienungsanleitung

Star Micronics

Star Micronics Delta Bedienungsanleitung

Star Micronics

Star Micronics TSP400 Series Bedienungsanleitung

Star Micronics

Star Micronics TSP600 Series Bedienungsanleitung

Star Micronics

Star Micronics TUP900 Series Bedienungsanleitung

Star Micronics

Star Micronics LC-7211 Bedienungsanleitung

Star Micronics

Star Micronics TSP800 Series Bedienungsanleitung

Star Micronics

Star Micronics TUP900 Series Bedienungsanleitung

Star Micronics

Star Micronics SP317 Bedienungsanleitung

Star Micronics

Star Micronics NX-1000 Bedienungsanleitung

Star Micronics

Star Micronics Star SCP700 Series Bedienungsanleitung

Star Micronics

Star Micronics futurePRNT TSP100 Handbuch

Star Micronics

Star Micronics TUP900 Series Bedienungsanleitung

Star Micronics

Star Micronics TSP600 Series Bedienungsanleitung

Star Micronics

Star Micronics Star SCP700 Series Bedienungs- und Wartungshandbuch

Star Micronics

Star Micronics NX-1020 Bedienungsanleitung

Star Micronics

Star Micronics NR-10 Bedienungsanleitung

Star Micronics

Star Micronics SB-15 Bedienungsanleitung

Star Micronics

Star Micronics TSP143IIU Bedienungsanleitung

Star Micronics

Star Micronics TSP100ECO Bedienungsanleitung

Star Micronics

Star Micronics SP200F Bedienungsanleitung

Star Micronics

Star Micronics 10X Bedienungsanleitung

Star Micronics

Star Micronics LC-7211 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung