Star Micronics TSP400 Series Bedienungs- und Wartungshandbuch

Thermal Printer

TSP400 Series

TUP400

Programmer’s Manual

TABLE OF CONTENTS

1. OUTLINE............................................................................................1

2. Memory Switch and DIP Switch.........................................................3

2-1. Memory Switch............................................................................3

3. Display panel and functions ................................................................4

3-1. LED..............................................................................................4

3-2. Switches .......................................................................................4

3-3. Power switch and ON LINE/FEED switch combinations ...........4

3-4. Sensor adjustment mode ..............................................................5

4. SERIAL INTERFACE ..........................................................................6

4-1. Interface Specifications................................................................6

4-2. Interface Circuit ...........................................................................7

4-2-1. RS-232C Interface .............................................................7

4-2-2. RS-422A Interface.............................................................7

4-3. Connectors and Signal Names .....................................................8

4-3-1. RS-232C Interface .............................................................8

4-3-2. RS-422A Interface.............................................................9

4-4. Interface Connections ................................................................10

4-5. Data Protocol..............................................................................11

4-5-1. DTR/DSR mode ..............................................................11

4-5-2. X-ON/X-OFF mode.........................................................13

4-5-3. STX-ETX mode...............................................................14

4-6. Error Status ...............................................................................16

5. PARALLEL INTERFACE..................................................................18

5-1. Interface Specifications..............................................................18

5-2. Interface Timing.........................................................................18

5-3. Connectors and Signal Names ...................................................19

6. PERIPHERAL UNIT DRIVE CIRCUIT ............................................21

6-1. Errors..........................................................................................23

7. CONTROL CODES/PAGE MODE....................................................24

8. CONTROL CODES/LINE MODE .....................................................61

8-1. Line Mode Command Summary................................................61

8-2. Command Specification .............................................................65

9. CHARACTER CODE TABLES.......................................................99

10. Automatic Cutter .............................................................................108

11. Presenter’s memory switch settings ................................................109

12. TSP LABEL ....................................................................................110

– 1 –

The TSP400 series is ideal for printing text, bar code and graphics.

The TSP400 series has the following features:

1. extremely quiet and fast printing (50 mm/sec.) using the direct line thermal

printing method

2. astraightpaperpath,whichpreventspaperjamsandisidealforlabelprinting

3. support for many bar code types

(UPC,JAN/EAN-8,JAN/EAN-13,CODE39,IFT2OF5,CODE128,CODE

93, NW-7)

4. a black mark sensor that detects the top of the page

5. a transmissive sensor that detects the gap between labels (no black mark is

necessary)

6. a large-diameter (115 mm) roll

7. a wide selection of interchangeable interfaces (RS232C, Centronics Parallel,

RS422A)

8. an installed heavy-duty and reliable cutter (TSP442 only)

9. enclosedutilitysoftware(TSPLABEL)thatmakesiteasiertodesignandprint

bar code labels

10.a memory switch that enables a wide selection of printer default settings and

easy setup using the enclosed utility software (TSPSETUP)

The printer has two different software modes which can be selected using the

memory switch. In order to enable changed memory switch settings, turn the

printer OFF and ON again or send printer reset command (<ESC>“?”) to the

printer.

(Factory setting: Page Mode)

Page Mode:

Code <ESC> “#0,0000” <LF> <NUL>

Hex 1B 23 30 2C 30 30 30 30 0A 00

Ideal for bar code label, graphics and text data printing.

Can locate and rotate bar code and text. Accepts a non-compressed BMP file so

that the printer can import and print a BMP file which is scanned or edited in

Windows applications.

1. OUTLINE

– 2 –

Line Mode:

Code <ESC> “#0,0001” <LF> <NUL>

Hex 1B 23 30 2C 30 30 30 31 0A 00

ThismodeiscompatiblewithStarReceiptprinters,suchastheSP300andSP200

series.

Forimprovementpurposes,thedescriptionsandspecificationsinthismanualare

subject to change without notice.

– 3 –

2. MEMORY SWITCHAND DIP SWITCH

Functionalsettings aremadeusingthe printer’sEEPROMmemoryswitchesand

the DIP switches located on the interface board.

2-1. Memory Switch

Each memory switch is a 16-bit word stored in EEPROM.

The printer is shipped with the factory setting which is made in accordance with

its product type.

For the detailed functions and the settings of the Memory switches, please refer

to "Chapter 7 and 8".

The factory settings are shown in the table below.

hctiwsyromoM214PST244PST284PUT

0#000000000000

1#000000000000

2#000000000000

3#000000000000

B#--1010

2-2. DIP Switch

For the detailed functions and the settings of theDIP switches, please refer to

"Installation manual".

– 4 –

3-1. LED

LED Function

POWER Lights up when the printer is turned on

HEAD UP

NO PAPER Lights up when an error occurs (Refer to 6-1 Errors.)

ERROR

ON LINE Lights up when the printer is on line; goes off when the printer

is off line; lights up when the head temperature is too high

3-2. Switches

Switch Function

ON LINE Switches between on line and off line

FEED Enable starting position: Feeds the paper to the next starting

position

Disable starting position: Feeds the paper while pressed

3-3. Power switch and ON LINE/FEED switch combinations

The following can be set when the power switch is turned on.

1) Power + FEED switches

1 short beep … Test print

HEAD UP LED lights up

2) Power + ON LINE switches

Approx. 2 sec. Approx. 2 sec.

1 short beep … 2 short beeps … 3 short beeps …

abc

HEAD UP LED NO PAPER LED ERROR LED

lights up lights up lights up

Pause at a: HEX dump

Pause at b: sensor selection

Press ON LINE 1 short beep Reflecting sensor

Press FEED 2 short beeps Transmissive sensor

3. DISPLAY PANELAND FUNCTIONS

– 5 –

Pause at c: command mode selection

Press ON LINE 1 short beep Page mode

Press FEED 2 short beeps Line mode

3) Power + ON LINE + FEED switches

Approx. Approx. Approx. Approx.

2 sec. 2 sec. 2 sec. 2 sec.

1 short beep … 2 short beeps … 3 short beeps … 1 long beep … …

abcde

HEAD UP NO PAPER ERROR LEDs flash All LEDs

LED LED LED successively light up

lights up lights up lights up lights up

Pause at a: RAM backup cleared

Pause at b: feed function selection

Press ON LINE 1 short beep Disable starting position

Press FEED 2 short beeps Enable starting position

Pause at c: sensor adjustment mode

Pause at d: no operation

Pause at e: clearing of all memory switches and test print

3-4. Sensor adjustment mode

a) Reflecting sensor (black mark sensor)

• Insert the paper in front of the sensor mechanism so that the sensor is not

positioned at a black mark.

• Turn the reflecting sensor adjustment controller VR4 on the PCB until the

HEAD UP LED lights up.

b) No paper sensor

• Insert the paper in front of the sensor mechanism so that the sensor is not

positioned at a black mark.

• TurnthereflectingsensoradjustmentcontrollerVR3onthePCBuntiltheNO

PAPER LED lights up.

c) Transmissive sensor

• Insert only the label’s base paper in front of the sensor mechanism.

• Turn the reflecting sensor adjustment controllers VR1 and VR2 on the PCB

until the ERROR LED lights up.

• VR1 is used for coarse adjustment and VR2 is used for fine adjustment.

– 6 –

4. SERIAL INTERFACE

4-1. Interface Specifications

Transmission type.................Asynchronous serial interface

Baud rate (bps) .....................2400, 4800, 9600, or 19200

(Selected by DIP switch)

Word format

Start bit: ......................1

Data bits: ....................7 or 8 (Selected by DIP switch)

Parity: .........................Odd, Even, or None

(Selected by DIP switch)

Stop bit: ......................1

Signal polarities

RS-232C .....................Mark = Logic “1” (–3V to –15V)

Space = Logic “0” (+3V to +15V)

RS-422A.....................Mark = Logic “1” (“A” negative with respect to

“B” by at least 0.2V: A B – 0.2V)

Space = Logic “0” (“A” positive with respect to

“B” by at least 0.2V: A B + 0.2V)

Handshaking .........................DTR or XON/XOFF mode (Selected by DIP

switch)

b0 b1 b2 b3 b4 b5 b6 (b7)

ABCD

Mark [1]

Space [0]

A: Start bit

B: Data bits

C: Vertical parity bit

D: Stop bit

SERIAL

– 7 –

75188 or equivalent

Printer Host computer

4-2. Interface Circuit

4-2-1. RS-232C Interface

Input (RXD, CTS)

Output (DTR, FAULT, TXD, RCH, RTS)

4-2-2. RS-422A Interface

Input (RD, RS)

Output (SD, CS)

SERIAL

Andere Handbücher für TSP400 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Star Micronics Drucker Handbücher

Star Micronics

Star Micronics LC-8521 Bedienungsanleitung

Star Micronics

Star Micronics SM-T400I Series Bedienungsanleitung

Star Micronics

Star Micronics TSP552II Bedienungsanleitung

Star Micronics

Star Micronics MULTI-FONT NX-1000II Bedienungsanleitung

Star Micronics

Star Micronics TSP600 Series Bedienungsanleitung

Star Micronics

Star Micronics TSP600 Series Bedienungsanleitung

Star Micronics

Star Micronics SP2000 Bedienungs- und Wartungshandbuch

Star Micronics

Star Micronics NX-2460C Bedienungsanleitung

Star Micronics

Star Micronics TSP1000 Series Montageanleitung

Star Micronics

Star Micronics SP300 Series Bedienungsanleitung

Star Micronics

Star Micronics NP-345 Montageanleitung

Star Micronics

Star Micronics DP8340R Series Bedienungsanleitung

Star Micronics

Star Micronics TSP 654IID Bedienungsanleitung

Star Micronics

Star Micronics NX-1020 Bedienungsanleitung

Star Micronics

Star Micronics SP312F Bedienungsanleitung

Star Micronics

Star Micronics TSP400 Series Bedienungsanleitung

Star Micronics

Star Micronics TSP800 Series Bedienungsanleitung

Star Micronics

Star Micronics TSP400 Series Bedienungsanleitung

Star Micronics

Star Micronics NP-226 Montageanleitung

Star Micronics

Star Micronics TUP400 Series Bedienungsanleitung

Star Micronics

Star Micronics NX-1020 Bedienungsanleitung

Star Micronics

Star Micronics SR-10/I5 Bedienungsanleitung

Star Micronics

Star Micronics NP-215 Bedienungsanleitung

Star Micronics

Star Micronics TSP400 Series Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung