Star Micronics TSP200 Series Bedienungs- und Wartungshandbuch

Thermal Printer

TSP200 Series

Programmer’s Manual

TABLE OF CONTENTS

1. OUTLINE..............................................................................................1

2. MEMORY SWITCH AND DIP SWITCH ...........................................2

2-1. Memory Switch............................................................................2

2-2. DIP Switch ...................................................................................2

3. DISPLAY PANEL AND FUNCTIONS ...............................................4

3-1. LED..............................................................................................4

3-2. Switches .......................................................................................4

3-3. Switch Operation (Combined Switch Operation) ........................4

4. SERIAL INTERFACE ..........................................................................5

4-1. Interface Specifications................................................................5

4-2. Interface Circuit ...........................................................................6

4-2-1. RS-232C Interface .............................................................6

4-3. Connectors and Signal Names .....................................................7

4-3-1. RS-232C Interface .............................................................7

4-4. Interface Connections ..................................................................9

4-5. Data Protocol..............................................................................10

4-5-1. DTR mode .......................................................................10

4-5-2. X-ON/X-OFF mode.........................................................12

5. PARALLEL INTERFACE..................................................................13

5-1. Interface Specifications..............................................................13

5-2. Interface Timing.........................................................................13

5-3. Connectors and Signal Names ...................................................14

6. PERIPHERAL UNIT DRIVE CIRCUIT ............................................16

7. ERRORS..............................................................................................19

7-1. Automatic Recovery (Power Lamp: Flashing;

On-Line Lamp: On)....................................................................19

7-2. Recoverable Errors (Power Lamp: Flashing;

On-Line Lamp: Off) ...................................................................19

7-3. Fatal Error (Power Lamp: Flashing;

On-Line Lamp: Flashing)...........................................................20

7-4. Type of buzzer sound (only Star mode) P: 50ms Pi: 100ms......20

8. CONTROL CODES/STAR MODE ....................................................21

8-1. Star Mode Command Summary.................................................21

8-2. Command Specification .............................................................25

9. CONTROL CODES/ESC/POS MODE ..............................................57

10. CHARACTER CODE TABLES .......................................................59

11. AUTOMATIC CUTTER...................................................................73

– 1 –

The TSP200 series is ideal for printing text, bar code and graphics.

The TSP200 series has the following features:

1. extremelyquietandfastprinting(maximum50mm/sec.)usingthedirectline

thermal printing method

2. support many bar code types

(UPC-A,UPC-E,JAN/EAN-8,JAN/EAN-13,CODE39,IFT 2 OF 5,CODE

128, CODE 93, NW-7)

3. dual interfaces (RS232C, Parallel)

4. memory switches that enable wide selection of printer default settings

TheprinterhastwodifferentsoftwaremodeswhichcanbeselectedusingtheDIP

switch.

(Factory setting: Star Mode)

Star Mode: DIP switch 1-7 ON

ThismodeiscompatiblewithStarReceiptprinters,suchastheSP300andSP200

series.

ESC/POS Mode: DIP switch 1-7 OFF

This mode is compatible with the printers supporting ESC/POS command.

1. OUTLINE

ESC/POS is a trademark of Seiko Epson Corporation.

Forimprovementpurposes,thedescriptionsandspecificationsinthismanualare

subject to change without notice.

– 2 –

2. MEMORY SWITCHAND DIP SWITCH

Functionalsettingsaremadeusingtheprinter’sEEPROMmemoryswitchesand

the DIP switches.

2-1. Memory Switch

Each memory switch is a 16-bit word stored in EEPROM.

The printer is shipped with the factory setting which is made in accordance with

its product type.

For the detailed functions and the settings of the Memory switches, please refer

to “Chapter 8”.

The factory settings are shown in the table below.

Memory switch TSP212 TSP242

#0 0000 0000

#1 0000 0000

#2 0000 0100

#3 0000 0000

#4 0000 0000

2-2. DIP Switch

Be sure to turn off the power of the printer before changing the setting of the

DIP switches.

DIP switch array

8141

OFF DIP switch 1

DIP switch

DIP switch 2

Power off

– 3 –

DIP switch #1

The factory settings of DIP switch 1 are all on.

Switch Contents ON OFF

1-1 Baud Rate

1-2

1-3 Data Length 8 bit 7 bit

1-4 Parity Check Disabled Enabled

1-5 Parity Selection Odd Even

1-6 Handshake DTR XON/XOFF

1-7 Operating Mode Star ESC/POS

1-8 Interface RS232C Parallel

Baud Rate 1-1 1-2

2400BPS OFF OFF

4800BPS ON OFF

9600BPS ON ON

19200BPS OFF ON

DIP Switch #2

Factory settings: 2-1 and 2-2 are on; 2-3 and 2-4 are off.

Switch Contents ON OFF

2-1 Print Density

2-2

2-3 Serial I/F No. 6 Pin Reset Signal Enabled Disabled

2-4 Serial I/F No. 8 Pin Reset Signal Enabled Disabled

Print Density 2-1 2-2

Light OFF OFF

Standard ON ON

Somewhat Heavy ON OFF

Heavy OFF ON

– 4 –

3-1. LED

LED Function

POWER Lights up when the printer is turned on.

Blinks when an error occurs (Refer to 7. ERRORS.)

ON LINE Lights up when the printer is on line; goes off when the printer

is off line or error occurs (Refer to 7. ERRORS.)

3-2. Switches

Switch Function

ON LINE Switches between on line and off line

FEED Feeds the paper while pressed

3-3. Switch Operation (Combined Switch Operation)

1) <SELF PRINTING>

FEED + POWER ON (Turn the power on while holding the FEED switch

depressed.)

Self-printing will be performed. VER. NO., Memory switch settings, DIP

switch settings and character order will be printed out.

2) <Hexadecimal dump mode>

ON LINE + POWER ON (Turn the power on while holding the ON LINE

switch depressed.)

Each of the signals sent from the computer to the printer will be printed out

in hexadecimal code.

This function allows you to check if a control code sent to the printer by the

program being used is correct or not. The last line is not printed if its data is

less than one full line. However, if the ON LINE switch is pressed to set the

offlinemode,thelastlinewillbeprinted.Toturnoffthemode,itisnecessary

to turn off the printer completely.

3. DISPLAY PANELAND FUNCTIONS

– 5 –

4. SERIAL INTERFACE

4-1. Interface Specifications

Transmission type.................Asynchronous serial interface

Baud rate (bps) .....................2400, 4800, 9600, or 19200

(Selected by DIP switch)

Word format

Start bit: ......................1

Data bits: ....................7 or 8 (Selected by DIP switch)

Parity: .........................Odd, Even, or None

(Selected by DIP switch)

Stop bit: ......................1

Signal polarities

RS-232C .....................Mark = Logic “1” (–3V to –15V)

Space = Logic “0” (+3V to +15V)

Handshaking .........................DTR or XON/XOFF mode (Selected by DIP

switch)

SERIAL

b0 b1 b2 b3 b4 b5 b6 (b7)

ABCD

Mark [1]

Space [0]

A: Start bit

B: Data bits

C: Vertical parity bit

D: Stop bit

– 6 –

75188 or equivalent

Printer Host computer

4-2. Interface Circuit

4-2-1. RS-232C Interface

Input (RXD, DSR)

Output (DTR, FAULT, TXD, RTS)

SERIAL

Andere Handbücher für TSP200 Series

Inhaltsverzeichnis

Andere Star Micronics Drucker Handbücher

Star Micronics

Star Micronics SP2000 Bedienungsanleitung

Star Micronics

Star Micronics LC-6211 Bedienungsanleitung

Star Micronics

Star Micronics LC-90 NX-1010 Bedienungsanleitung

Star Micronics

Star Micronics SP300 Series Bedienungs- und Wartungshandbuch

Star Micronics

Star Micronics TSP800 Series Bedienungsanleitung

Star Micronics

Star Micronics TSP043 Series Bedienungsanleitung

Star Micronics

Star Micronics TSP600 Series Bedienungsanleitung

Star Micronics

Star Micronics LC-8211 Bedienungsanleitung

Star Micronics

Star Micronics LC-200 Bedienungsanleitung

Star Micronics

Star Micronics USB Bedienungsanleitung

Star Micronics

Star Micronics TUP900 Series Bedienungsanleitung

Star Micronics

Star Micronics TSP400Z Series Bedienungsanleitung

Star Micronics

Star Micronics NX-2400 Bedienungsanleitung

Star Micronics

Star Micronics TSP700 Series Bedienungsanleitung

Star Micronics

Star Micronics NX-1040 Bedienungsanleitung

Star Micronics

Star Micronics TCP300 Series Bedienungs- und Wartungshandbuch

Star Micronics

Star Micronics TSP700II Series Bedienungsanleitung

Star Micronics

Star Micronics Radix Bedienungsanleitung

Star Micronics

Star Micronics TSP100ECO Bedienungsanleitung

Star Micronics

Star Micronics TSP143IIU Bedienungsanleitung

Star Micronics

Star Micronics SB-10 Bedienungsanleitung

Star Micronics

Star Micronics Line Thermal Printer Bedienungsanleitung

Star Micronics

Star Micronics SP500 Series Montageanleitung

Star Micronics

Star Micronics lC-10 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung