Star Micronics TSP650II SERIES Bedienungsanleitung

THERMAL PRINTER

TSP650II SERIES

Hardware Manual

Federal Communications Commission

Radio Frequency Interference

Statement

is device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) is device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: is equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules. ese limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

For compliance with the Federal Noise Interference Standard, this equipment requires a shielded cable.

For RF interference suppression, if a ferrite core is provided with this device, ax it to the interface cable.

is statement will be applied only for the printers marketed in U.S.A.

Statement of

e Canadian Department of Communications

Radio Interference Regulationst

is Class A digital apparatus complies with Canadian ICES-003.

e above statement applies only to printers marketed in Canada.

Trademark acknowledgments

TSP650II : Star Micronics Co., Ltd.

Notice

permission is forbidden.

•e contents of this manual are subject to change without notice.

•All eorts have been made to ensure the accuracy of the contents of this manual at the time of going to press.

However, should any errors be detected, STAR would greatly appreciate being informed of them.

•e above notwithstanding, STAR can assume no responsibility for any errors in this manual.

2013 Star Micronics Co., Ltd..

< For Bluetooth models >

Federal Communications Commission

Radio Frequency Interference

Statement

is device complies with Part 15 of the FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following

two conditions:

(1)this device may not cause harmful interference, and

(2)this device must accept any interference received,including interference that may cause undesired operation.

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and

meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio

frequency (RF) Exposure rules. is equipment has very low levels of RF energy that it deemed to comply without

maximum permissive exposure evaluation(MPE). But it is desirable that it should be installed and operated keeping

the radiator at least 20cm or more away from person's body (excluding extremities: hands,wrists,feet and ankles).

is statement will be applied only for the printers marketed in U.S.A and Canada.

CE MARKING WARNING

Hereby, Star Micronics Co., Ltd. declares that this device is in compliance with the essential requirements and other

relevant provisions of Directive 1999/5/EC.

Notice) is device can be operated in all European countries.

Italy: e public use is subject to general authorisation by the respective service provider.

Norway: is subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-

Alesund.

is statement will be applied only for the printers marketed in Europe.

TABLE OF CONTENTS

1. Unpacking and Installation......................................................................... 1

1-1. Unpacking .................................................................................................... 1

1-2. Notes about Installation ............................................................................... 1

2. Parts Identication and Nomenclature....................................................... 2

3. Setup ............................................................................................................ 3

3-1. Connecting the Interface Cable to the PC...................................................... 3

3-2. Connecting the Interface Cable to the Printer ............................................... 4

3-3. Connecting the AC Adapter .......................................................................... 7

3-4. Turning the Power On................................................................................... 8

3-5. Connecting to a Peripheral Device ................................................................ 8

3-6. Loading a Paper Roll..................................................................................... 9

3-7. Bluetooth Setting (For Bluetooth Interface Model only)..................................... 12

3-8. Setup Precautions ....................................................................................... 15

4. Attaching the Accessories.......................................................................... 17

4-1. Attaching the Holder Plate.......................................................................... 17

4-2. Attaching the Rubber Feet .......................................................................... 19

4-3. Switch Cover Installation............................................................................ 19

5. Adjusting the Near-end Sensor ................................................................. 20

6. Error Indicators......................................................................................... 21

6-1. Recoverable errors ...................................................................................... 21

6-2. Unrecoverable errors .................................................................................. 21

7. Preventing and Removing Paper Jams...................................................... 22

7-1. Preventing Paper Jams ................................................................................ 22

7-2. Removing Paper Jams ................................................................................. 22

7-3. Releasing the Cutter Lock ........................................................................... 23

8. Maintenance............................................................................................... 24

8-1. Thermal Head............................................................................................. 24

8-2. Platen Rubber Roller .................................................................................. 24

8-3. Paper Holder .............................................................................................. 24

1. Unpacking and Installation

* Accessories vary depending on the model and the

region where the printer was purchased.

Paper roll

Printer

Holding plate

Screws

Switch blind

Safety Instruction

Setup sheet

CD-ROM

Paper roll guide

Rubber feet

1-1. Unpacking

Aer unpacking the unit, check that all the necessary accessories are included in the package.

1-2. Notes about Installation

1. Choose a rm, level surface where the printer will not be exposed to vibration.

2. Make sure that the printer is connected to a reliable power outlet. It should not be on the same electric circuit as copi-

ers, refrigerators, or other appliances that cause power spikes.

3. e power outlet you plan to connect to for power should be nearby and unobstructed.

4. Make sure that the printer is not exposed to direct sunlight.

5. Make sure that the printer is well away from heaters and other sources of extreme heat.

6. Make sure that the printer is connected to a reliable power outlet. It should not be on the same electric circuit as copi-

ers, refrigerators, or other appliances that cause power spikes.

7. Make sure that the room where you are using the printer is not too humid.

8. Use the printer within the boundaries indicated in the environmental requirements. Even when the ambient tem-

perature and humidity are within the specications, avoid radical changes in environmental conditions. e suitable

operating temperature range is as follows:

Operating temperature: 5°C to 45°C

9. When disposing of the printer, obey local regulations.

ERROR

FEED

POWER

TSP650

2. Parts Identication and Nomenclature

Control panel

Features lamps that indicate printer

status and a button for operating

the printer.

Printer cover

Open to replace paper.

Do not open while printing.

Power switch

Turns theprinteron

and o.

Connects to peripheral devices

such as cash drawers.

Do not connect this to a tel-

ephone line.

Peripheral drive connector

Connects to an optional

AC adapter.

Power inlet

Connects to a host PC

through a cable.

Interface connector

Lights when the printer is online.

This lamp also indicates errors, in

combination with other lamps.

POWER lamp (green)

Lights when the cover is open.

This lamp also indicates errors, in

combination with other lamps.

ERROR lamp (red)

When the printer is online, pressing

this button feeds the paper roll.

FEED button

Cover open lever

Use this lever to open the

printer cover.

3. Setup

3-1. Connecting the Interface Cable to the PC

3-1-1. Parallel Cable

Connect the parallel cable to a parallel port on your PC.

3-1-2. RS-232C Cable

Connect the RS-232C cable to a RS-232C port on your PC.

3-1-3. USB Cable

Connect the USB cable to a USB port on your PC.

3-1-4. Ethernet Cable

Connect the Ethernet cable to a USB port on your PC.

Parallel interface cable

Ferrite core

Interface cable

5 cm

(maximum)

Fastener

Pull and cut

3-2. Connecting the Interface Cable to the Printer

Printer cables are not included in the package.

Obtain an appropriate cable that complies with the specications beforehand.

Because the appropriate interface cable diers depending on the system that you are connecting the printer to, contact

the dealer that you bought the product from if you are unsure about what cable to use.

Before connecting or disconnecting an interface cable, be sure to disconnect the AC adapter’s power cord from the outlet.

3-2-1. Parallel Interface Cable

To connect a parallel cable, follow the procedure given below.

(1) Make sure the printer is turn o.

(2) Ax the ferrite core onto the cable as shown in the illustration.

(3) Pass the fastener through the ferrite core.

(4) Loop the fastener around the cable and lock it. Use scissors to cut

o any excess.

(5) Connect the interface cable to the connector on the rear panel of

the printer.

(6) Fasten the connector clasps.

RS-232C interface cable

USB cable

Cable hook

4 cm (maximum)

3-2-2. RS-232C Interface Cable

(1) Make sure that the AC adapter’s power cord is not connected to the outlet.

(2) Connect the interface cable to the connector on the rear panel of the printer.

(3) Tighten the connector screws.

3-2-3. USB Cable

To connect a USB cable, follow the procedure given below.

(1) Make sure that the AC adapter’s power cord is not connected to the outlet.

(2) Connect the USB cable to the USB port.

(3) As shown in the gure, pass the cable through the cable hooks to hold it in place.

Ethernet cable

IFBD-HE07

3-2-4. Ethernet Cable

To connect the cable, follow the procedure given below.

(1) Make sure that the AC adapter’s power cord is not connected to the outlet.

(2) Connect the Ethernet cable to the Ethernet port.

g Link disconnection detection feature

e Ethernet interface model is equipped with a link disconnection detection feature.

If the printer is turned on when an Ethernet cable is not connected to it, the POWER and ERROR lamps are simul-

taneously turned on and o at 4-second intervals to indicate the disconnection.

Be sure to connect the Ethernet cable from a PC or hub to the printer, and then turn the printer on.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Star Micronics Drucker Handbücher

Star Micronics

Star Micronics LC-240 Bedienungsanleitung

Star Micronics

Star Micronics Multi-Font NX-2410 Bedienungsanleitung

Star Micronics

Star Micronics NP-215 Bedienungsanleitung

Star Micronics

Star Micronics LC-7211 Bedienungsanleitung

Star Micronics

Star Micronics SP300 Series Bedienungs- und Wartungshandbuch

Star Micronics

Star Micronics SP 200 Bedienungsanleitung

Star Micronics

Star Micronics LC-1011C Bedienungsanleitung

Star Micronics

Star Micronics 10X Bedienungsanleitung

Star Micronics

Star Micronics NP-266S Montageanleitung

Star Micronics

Star Micronics NP-IO Bedienungsanleitung

Star Micronics

Star Micronics TSP700II Series Bedienungsanleitung

Star Micronics

Star Micronics SP700 Series Bedienungsanleitung

Star Micronics

Star Micronics USB Bedienungsanleitung

Star Micronics

Star Micronics LaserPrinter4 Bedienungsanleitung

Star Micronics

Star Micronics DP8340R Series Bedienungsanleitung

Star Micronics

Star Micronics TUP500 series Bedienungsanleitung

Star Micronics

Star Micronics NL-10 Bedienungsanleitung

Star Micronics

Star Micronics LC-500 Bedienungsanleitung

Star Micronics

Star Micronics LC-4511 Bedienungsanleitung

Star Micronics

Star Micronics NX-1000 Bedienungsanleitung

Star Micronics

Star Micronics TSP400 Series Bedienungsanleitung

Star Micronics

Star Micronics LC-7211 Bedienungsanleitung

Star Micronics

Star Micronics Star DP8340 Bedienungsanleitung

Star Micronics

Star Micronics TSP200 Series Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung