Star Micronics TSP552II Bedienungsanleitung

THERMAL PRINTER

TSP552II

USER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

MANUALE DI ISTRUZIONI

Federal Communications Commission

Radio Frequency Interference

Statement

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

For compliance with the Federal Noise Interference Standard, this equipment requires a

shielded cable.

This statement will be applied only for the printers marketed in U.S.A.

Statement of

The Canadian Department of Communications

Radio Interference Regulations

This digital apparatus does not exceed the Class A limits for radio noise emissions from

digital apparatus set out in the Radio Interference Regulations of the Canadian Department

of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le

brouillage radioélectrique édicté par le ministère des Communications du Canada.

The above statement applies only to printers marketed in Canada.

Manufacturer’s Declaration of Conformity

EC Council Directive 89/336/EEC of 3 May 1989

This product, has been designed and manufactured in accordance with the International

Standards EN 50081-1/01.92 and EN 50082-1/01.92, following the provisions of the

ElectroMagneticCompatibilityDirectiveoftheEuropeanCommunitiesasofMay1989.

EC Council Directive 73/23/EEC and 93/68/EEC of 22 July 1993

This product, has been designed and manufactured in accordance with the International

Standards EN 60950, following the provisions of the Low Voltage Directive of the

European Communities as of July 1993.

The above statement applies only to printers marketed in EU.

Trademark acknowledgments

TSP552II: Star Micronics Co., Ltd.

ESC/POS: Seiko Epson Corporation

Notice

without STAR’s express permission is forbidden.

•The contents of this manual are subject to change without notice.

•All efforts have been made to ensure the accuracy of the contents of this manual at the

time of going to press. However, should any errors be detected, STAR would greatly

appreciate being informed of them.

•The above notwithstanding, STAR can assume no responsibility for any errors in this

manual.

TABLE OF CONTENTS

1. Outline ..............................................................................................................1

2. Parts Identification and Nomenclature .........................................................2

3. Consumable Parts and AC Adapter ..............................................................4

4. Connecting Cables and AC Adapter..............................................................5

4-1. Connecting the Interface Cable..............................................................5

4-2. Connecting the Peripheral Drive Cable .................................................6

4-3. Connecting the optional AC Adapter.....................................................7

4-4. Turning Power On .................................................................................8

5. Control Panel ...................................................................................................9

5-1. PAPER FEED Switch ............................................................................9

5-2. POWER LED.........................................................................................9

5-3. ERROR LED .........................................................................................9

6. Loading Paper................................................................................................10

6-1. Loading New Roll Paper......................................................................10

6-2. Removing Remaining Paper ................................................................12

7. Command Summary .....................................................................................13

7-1. Star Mode..............................................................................................13

7-2. ESC/POS Mode ...................................................................................17

8. Preventing and Clearing Paper Jams ..........................................................19

8-1. Preventing Paper Jams .........................................................................19

8-2. Removing Paper Jam ...........................................................................19

9. Test Print Method..........................................................................................21

9-1. Producing a Test Print..........................................................................21

9-2. Hexadecimal Dump .............................................................................21

10. Periodical Cleaning .....................................................................................22

10-1.Cleaning the Thermal Head .................................................................22

10-2.Cleaning the Paper Holder ...................................................................22

Appendix A: Specifications...............................................................................95

A-1. General Specifications .........................................................................95

A-2. Print Specifications ..............................................................................95

A-3. Interface ...............................................................................................95

A-4. Power supply........................................................................................96

A-5. Environmental requirements ................................................................96

A-6. Reliability.............................................................................................96

Appendix B: Dip Switch Setting.......................................................................97

B-1. Serial Interface Type............................................................................97

B-2. Parallel Interface Type .........................................................................98

ENGLISH

Appendix C: Interface.....................................................................................100

C-1. Serial Interface ...................................................................................100

C-2. Two-way parallel interface (IEEE1284) ............................................103

C-3. Peripheral Drive Connector ...............................................................106

C-4. Power Connector................................................................................108

Please access the following URL

http://www.star-micronics.co.jp/service/frame_sp_spr_e.htm

for the lastest revision of the manual.

ENGLISH

– 1 –

ENGLISH

1. Outline

This manual explains how to use the thermal printer TSP552II and provides

points to note for safe use and prevention of problems and malfunctions.

Before using the printer, please read this manual thoroughly to ensure its

optimum use.

The major features of the printer are as follows:

1. Printsathighspeed(max.130mm/sec, 28linespersecondwhenthelinefeed

is set to 3.75 mm)

2. Quality print (8 dots/mm) thanks to the high-density line thermal print head.

3. Low noise due to line thermal technology.

4. Logo, coupon, and bar code printing is available.

5. Print density can be adjusted by DIP switches.

6. An auto cutter is provided as standard.

7. The built-in peripheral unit driver enables control of two peripheral units.

8. Considerable ease of paper loading thanks to the paper drop-in structure.

9. The paper drop-in structure makes maintenance easy.

10.The compact size requires only a small installation space.

11.Supports ESC/POS TM commands.

– 2 –

ENGLISH

2. Parts Identification and Nomenclature

Control panel

Features LED indica-

tors to indicate printer

status and switches to

operate the printer.

DIP switch

Used to make various

settings.

Lever

Pull down this lever to open

the printer cover.

Switch

Used to turn on/off

power to the printer.

Printer cover

Open this

cover to load

or replace

paper.

Roll paper User’s manual

Power connector Peripheral drive connector Interface connector

– 3 –

ENGLISH

Choosing a place for the printer

Before actually unpacking the printer, you should take a few minutes to

think about where you plan to use it. Remember the following points

when doing this.

✓Choose a firm, level surface where the printer will not be exposed to

vibration.

✓The power outlet you plan to connect to for power should be nearby

and unobstructed.

✓Make sure that the printer is close enough to your host computer for

you to connect the two.

✓Make sure that the printer is not exposed to direct sunlight.

✓Makesurethattheprinteriswellawayfromheatersandothersources

of extreme heat.

✓Make sure that the surrounding area is clean, dry, and free of dust.

✓Make sure that the printer is connected to a reliable power outlet. It

should not be on the same electric circuit as copiers, refrigerators, or

other appliances that cause power spikes.

✓Make sure that the room where you are using the printer is not too

humid.

– 4 –

ENGLISH

3. Consumable Parts andAC Adapter

When consumable parts have run out, use those specified in the table below.

Make sure that the AC adapter specified in the table is used.

Use of consumable parts or AC adapter which are not specified in the table may

result in damage to the printer, fire or electric shock.

Parts Name Specifications

Roll paper Thermal paper

Width: 80 mm

Outer roll diameter: ø83 mm or less

Core outer diameter: ø18 mm

Core inner diameter: ø12 ±0.5 mm

Recommended paper (Normal type paper)

TF50KS-E2C (Nippon Paper Industries)

PD-150R (Oji Paper Co., Ltd.)

P220AG (Mitsubishi Paper Mills Limited)

Recommended paper (High image stability paper)

PD-160R (Oji Paper Co., Ltd.)

HP220AB-1 (Mitsubishi Paper Mills Limited)

HP220A (Mitsubishi Paper Mills Limited)

AC adapter (Option) Input: 90 to 264 V AC

Output: 24 V DC

Important!

AccessthefollowingURLfortheinformationoftherecommendedpaper.

http://www.star-micronics.co.jp/

- 1.0

+0.5

– 5 –

ENGLISH

4. Connecting Cables andACAdapter

4-1. Connecting the Interface Cable

Note: Before connecting/disconnecting the interface cable, make sure that

power to the printer and all the devices connected to the printer is

turned off. Also make sure the power cable plug is disconnected from

the AC outlet.

(1)Connect the interface cable to the connector on the rear panel of the printer.

(2)In the case of a serial interface, tighten the connector screws. In the case of a

parallel interface, fasten the connector clasps.

(3)Pass the interface cable through the hole provided at the bottom of the printer

cover, then place the printer in position.

Note: Make sure that the interface cable is passed through the hole. Failure

to do so may cause the cable to be squashed by the printer, resulting in

damage to the cable.

Serial interface cable

Parallel interface cable

– 6 –

ENGLISH

4-2. Connecting the Peripheral Drive Cable

Note: Before connecting/disconnecting the peripheral drive cable, make

sure that power to the printer and all the devices connected to the

printer is turned off. Also make sure the power cable plug is discon-

nected from the AC outlet.

(1)Connect the peripheral drive cable to the connector on the rear panel of the

printer,andpassitthroughthecableholeprovidedatthebottomoftheprinter

cover.

Note: Make sure that the peripheral drive cable is passed through the hole.

Failure to do so may cause the cable to be squashed by the printer,

resulting in damage to the cable.

Inhaltsverzeichnis

Sprachen:

Andere Star Micronics Drucker Handbücher

Star Micronics

Star Micronics TSP700 Series Bedienungsanleitung

Star Micronics

Star Micronics LC-7211 Bedienungsanleitung

Star Micronics

Star Micronics SP349 Bedienungsanleitung

Star Micronics

Star Micronics DP8340R Series Bedienungsanleitung

Star Micronics

Star Micronics MP100 Handbuch

Star Micronics

Star Micronics XB24-10 Bedienungsanleitung

Star Micronics

Star Micronics DP8340 Series Betriebsanleitung

Star Micronics

Star Micronics mC-Print3 MCP31L Kurzanleitung

Star Micronics

Star Micronics NR-10 Bedienungsanleitung

Star Micronics

Star Micronics LC24-30 Colour Bedienungsanleitung

Star Micronics

Star Micronics NX-1000 Bedienungsanleitung

Star Micronics

Star Micronics TSP400 Series Bedienungsanleitung

Star Micronics

Star Micronics SP500 Series Montageanleitung

Star Micronics

Star Micronics futurePRNT TSP100 Handbuch

Star Micronics

Star Micronics SM-S230I Series Bedienungsanleitung

Star Micronics

Star Micronics LaserPrinter4 Bedienungsanleitung

Star Micronics

Star Micronics TCP300 Series Bedienungs- und Wartungshandbuch

Star Micronics

Star Micronics NP-255 Montageanleitung

Star Micronics

Star Micronics TSP1000 Series Montageanleitung

Star Micronics

Star Micronics TSP400 Series Bedienungs- und Wartungshandbuch

Star Micronics

Star Micronics DP8340 Series Bedienungsanleitung

Star Micronics

Star Micronics TSP200 Series Bedienungsanleitung

Star Micronics

Star Micronics FVP-10U Bedienungsanleitung

Star Micronics

Star Micronics NX-100 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung