Star Micronics ND-10/15 Bedienungsanleitung

ND-10115

USER’S MANUAL

NOT INTENDED FOR SALE

PN 80820163

Federal Communications Commission

Radio Frequency Interference Statement

This equipment generates and uses radio frequency energy and if not mstalled and used

properly. that is. in strict accordance with the manufacturer’s instructions. may cause

interference to radio and television reception It has been type tested and found to comply

with the limits for a Class B computing device in accordance with the specifications in

Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection

against such interference in a restdential installation. However. there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause

interference to radio or television reception. which can be determined by turning the

eqmpment off and on. the user is encouraged to try to correct the Interference by one

ot- more of the following measures:

l Reorient the receiv-ing antenna

l Relocate the computer with respect to the receiver

l Move the computer away from the receiver

l Plug the computer into a different outlet so that computer and receiver are on

different branch circuits.

If necessary, the user should consult the dealer or an experienced redio/teIevision tech-

nician for additional suggestions. The user may find the following booklet, prepared

by the Federal Communications Commission helpful: “How to Identify and Resolve

Radio-TV Interference Problems.” This booklet is available from the U.S. Government

Printing Office, Washington. D.C., 20402. Stock No. 004-000-00345-4.

For compliance with Federal Noise Interference Standard, this eqmpment requires a

shielded cable.

This statement willbe applied onlyfor the printers marketed in U.S.A.

Self Declaration

Radio interferences regarding this equipment has been eliminated according to Vfg

1046/1984 announced by the DBP.

DBP has been informed about the introduction of this special equipment and has been

conceded the right to examine the whole series.

It is upon the responsibility of the user to assume that his own assembled system is in

accordance with the technical regulations under Vfg 1046/1984.

To observe FTZ-regulations it is necessary, to establish all connections to the printer

with shielded cable.

The equipment may only be opened by qualified service representatives.

This statement willbe applied onlyfor the printers marketed in West Germany.

Trademark Acknowledgement

ND-10/15: Star Micronics Co., Ltd.

Apple II: Apple Computer Inc.

EasyWriter II: Information Unlimited Software. Inc.

FX-85: Seiko Epson Corp.

IBM PC, IBM Graphics Printer, IBM Proprinter: International Business Machines Corp.

Lotus l-2-3: Lotus Development Corp.

Microsoft BASIC: Microsoft Corporation

WordStar: MicroPro International Corporation

NOTICE

soever, without STAR’s express permission is forbidden.

l The contents of this manual are subject to change without notice.

l All efforts have been made to ensure the accuracy of the contents of this manual

at the time of going to press. However, should any errors be detected, STAR would

be greatly appreciate being informed of them.

l The above notwithstanding, STAR can assume no responsibility for any errors

in this manual.

Table of Contents

Chapter 1 Setting Up Your Printer

Locating the printer

Check the carton contents

Removing the printer cover

Removing the packing tube

Installing the ribbon cartridge

Installing the mute cover

Installing the interface board

Chapter 2 Getting to Know Your Printer

Controls and parts of the printer

Parts of the printer

Controls and indicators

Extra functions

Other controls

Selecting and loading paper

Loading single sheets

Loading sprocket-feed paper

Adjusting the print head

Testing the printer

Connecting the printer

Chapter 3 Using the Printer with Commercial Software 21

Using commercial software

Word processing with the printer

General concepts

The escape code

The master reset code

Using Near Letter Quality (NLQ)

Getting the most from your print choices

Using the printer with EasyWriter II

Redefining pitch settings and print control

codes

A sample printout with EasyWriter II

Redefining .your own print pitches

Redefining your own print control keys

Using the printer with WordStar

User-defind print commands

Using the printer with Lotus l-2-3

Using the panel modes

Advanced panel functions

Setting print start position

Setting the top of form

Setting the left and right margins

Chapter 4 Printing with BASIC

Some basics of BASIC

First steps

ASCII codes and the CHR$ function

Control codes

The escape codes

A note on command syntax

Selecting the right software mode

Some special kinds of text

Near Letter Quality characters

Italic printing

Underlining and overlining

Superscripts and subscripts

Changing the print pitch

Expanded print

Condensed print

Proportional printing

Making words stand out

Mixing print modes

Chapter 5 Formatting Text

Lines and line spacing

Starting a new line

Reverse line feeds

Changing the line spacing

Moving down the page without a carriage

return

Page control

Form feed

Reverse form feed

Changing the page length

Top and bottom margins

Setting left and right margins

Horizontal and vertical tabs

Horizontal tabs

One-time horjzontal tabs

Vertical tabs

Vertical tab channels

Centering and aligning text

Chapter 6 Special Features of the Printer

Now hear this

Resetting the printer

Taking the printer off line

Printing the bottom of the sheet

Backspace, delete, and cancel text

Printing zeroes

Immediate-print

Adjusting the width of space between

characters

Uni-directional printing

The seven bit dilemma

Block graphics characters and special

symbols

Chapter 7

International characters sets

Printing characters in the control code area

Printing BIG characters

The optional sheet feeder

The macro control code

Reading a hex dump

Download Characters and Dot Graphics 103

Dot matrix printing

Designing your own characters

Defining proportional characters

Downloading with the IBM-P mode

Designing your own NLQ characters

User-designed Dot Graphics

Higher resolution graphics

More graphics programming tips

Redefining alternate graphics codes

9-pin graphics mode

Chapter 8 Caring for Your Printer

Cleaning the printer

Replacing the ribbon

Replacing the .print head

Appendix A DIP Switch Settings

Switch functions

123

Appendix B ASCII Codes and Conversion Chart

129

135

Appendix C Function Codes

Commands to control print style

Font style controls

Print pitch controls

Special print modes

Controlling the vertical print position

Line feed and reverse line feed

Form feed and related commands

Top/bottom margins and vertical tabs

Controlling the horizontal print position

Download character commands

Dot graphics commands

Macro instruction commands

Other commands

Appendix D Command Summary in Numeric Order

Standard mode

IBM-P mode

IBM-G mode

147

201

Appendix E Technical Specifications

Appendix F The Parallel Interface

Functions of the Connector Signals

Appendix G Serial Interface Specifications

Configuring the serial interface

The serial protocols

215

219

223

Index

Serial busy protocols

XON/XOFF protocol

ACK protocol

CHAPTER 1

SETTING UP YOUR

PRINTER

Subjects covered in Chapter 1 include -

l Choosing a suitable place for your printer

l Unpacking

l Setting up

LOCATING THE PRINTER

Give some thought to the best place to put the printer. Both

the printer and computer should be used in normal office

surroundings. For best performance, we recommend:

l Use the printer on a flat surface.

l Keep it out of direct sunlight and away from

heat-producing appliances.

l Use it only in temperatures where you are comfortable.

l Avoid locations with dust, grease, or high humidity.

l Supply it “clean” electricity. Don’t connect it to the

same circuit used by large, noise-producing appliances

(such as refrigerators).

l Make sure the line voltage is within 10% of the voltage

specified on the identification plate.

CHECK THE CARTON CONTENTS

Open the carton and check each item in the box against

Figure l- 1to make sure that you have everything (there should

be five items).

You should also have a parallel interface board to connect

your computer to the printer. Also available are a parallel

interface board with extra buffer memory and a serial interface

board, both optional. (More on interfaces later.)

Figure l-l. Check to make sure you have all five items: 1) Printer,

2) Mute cover, 3) Paper guide, 4) Ribbon cartridge and 5) User’s

manual.

q Removing the printer covei

The printer’s cover is important for two reasons - it keeps

dust and dirt away from the printer’s delicate mechanism, and

it absorbs nearly all of the printer’s operating sounds. Don’t

take off the cover unless you have to change the ribbon or

make an adjustment.

To remove the cover, lift up the back of the cover to disengage

the two or three tabs at the front, then lift it off the rest of

the way. To replace the cover, slide the tabs in at the front

and lower it into place. Figure l-2 shows the proper position

and movement for both removing and replacing the cover.

Printer cover

Figure 1-2. Remove the printer cover by lifting carefully.

W Removing the packing tube

The printer is shipped with a protective spiral tube to keep

the print head from being damaged during shipping. This tube

must be removed before use. First, take off the printer cover.

The protective tube is split along its bottom side to allow easy

removal. Grasp one end of the spiral tube and firmly pull it

upward and away from the carriage rail.

Figure 1-3. Remove the protective tube from the carriage rail.

N Installing the ribbon cartridge

This printer uses a neat, easy-to-change ribbon cartridge

with automatic threading. To fit or change the ribbon car-

tridge:

1. Turn oj,Ythe power and remove the printer cover.

2. Slide the print head gently to the center of the printer.

Warning: The print head gets hot during operation,

so let it cool off before you touch it.

3. Set the release lever to either single sheet or sprock-

et-feed paper.

4. With the ribbon facing away from you, use the guide

hold.ers as a fulcrum and lightly press the cartridge down

until the two holder springs snap shut to hold the

cartridge firmly in place. See Figure l-4.

5. Check that the cartridge fits so that the drive pins

engage the cartridge teeth, by turning the ribbon ad-

vance knob.

6. Gently slide the print head carriage manually all the

way to your right or left until the ribbon automatically

slips down into its proper place between the print head

and the silver ribbon guide.

7. Replace the printer cover. (A switch on the printer

prevents the printer from operating when the cover is

off.)

Ribbon advance kno

Figure l-4. Press the cartridge into place until the holding springs snap

into place.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Star Micronics Drucker Handbücher

Star Micronics

Star Micronics TSP143IIIBI Bedienungsanleitung

Star Micronics

Star Micronics NX-2450 Bedienungsanleitung

Star Micronics

Star Micronics TSP600 Series Bedienungs- und Wartungshandbuch

Star Micronics

Star Micronics SP500 Series Bedienungsanleitung

Star Micronics

Star Micronics LC-1011C Bedienungsanleitung

Star Micronics

Star Micronics TUP900 Series Bedienungsanleitung

Star Micronics

Star Micronics Star SCP700 Series Bedienungsanleitung

Star Micronics

Star Micronics LC-6211 Bedienungsanleitung

Star Micronics

Star Micronics SP500 Series Benutzerhandbuch

Star Micronics

Star Micronics TSP143LAN Handbuch

Star Micronics

Star Micronics TSP400Z Series Bedienungsanleitung

Star Micronics

Star Micronics TSP200 Series Bedienungs- und Wartungshandbuch

Star Micronics

Star Micronics LC-100+ Bedienungsanleitung

Star Micronics

Star Micronics LC-20 Bedienungsanleitung

Star Micronics

Star Micronics lC-10 Bedienungsanleitung

Star Micronics

Star Micronics LaserPrinter 4III Bedienungsanleitung

Star Micronics

Star Micronics lC-10 Bedienungsanleitung

Star Micronics

Star Micronics SLIP SP298 SERIES Bedienungsanleitung

Star Micronics

Star Micronics SP200 Series Bedienungsanleitung

Star Micronics

Star Micronics NP-226 Montageanleitung

Star Micronics

Star Micronics TUP900 Series Bedienungsanleitung

Star Micronics

Star Micronics NX-10 Bedienungsanleitung

Star Micronics

Star Micronics TSP700II Series Bedienungsanleitung

Star Micronics

Star Micronics SP500 Series Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung