Star Micronics TSP600 Series Bedienungsanleitung

THERMAL PRINTER

TSP600 SERIES

USER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

MANUALE DI ISTRUZIONI

Federal Communications Commission

Radio Frequency Interference

Statement

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

For compliance with the Federal Noise Interference Standard, this equipment

requires a shielded cable.

This statement will be applied only for the printers marketed in U.S.A.

Statement of

The Canadian Department of Communications

Radio Interference Regulations

This digital apparatus does not exceed the ClassA limits for radio noise emissions

from digital apparatus set out in the Radio Interference Regulations of the Canadian

Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les

limites applicables aux appareils numériques de la classe A prescrites dans le Règlement

sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

The above statement applies only to printers marketed in Canada.

Manufacturer’s Declaration of Conformity

EC Council Directive 89/336/EEC of 3 May 1989

This product, has been designed and manufactured in accordance with the

International Standards EN 50081-1/01.92 and EN 50082-1/01.92, following the

provisions of the Electro Magnetic Compatibility Directive of the European Communi-

ties as of May 1989.

EC Council Directive 73/23/EEC and 93/68/EEC of 22 July 1993

This product, has been designed and manufactured in accordance with the

International Standards EN 60950, following the provisions of the Low Voltage

Directive of the European Communities as of July 1993.

The above statement applies only to printers marketed in EU.

Trademark acknowledgments

TSP600: Star Micronics Co., Ltd.

ESC/POS: Seiko Epson Corporation

Notice

without STAR’s express permission is forbidden.

•The contents of this manual are subject to change without notice.

•All efforts have been made to ensure the accuracy of the contents of this manual at

the time of going to press. However, should any errors be detected, STAR would

greatly appreciate being informed of them.

•The above notwithstanding, STAR can assume no responsibility for any errors in

this manual.

TABLE OF CONTENTS

1. Parts Identification and Nomenclature .........................................................1

2. Consumable Parts and AC Adapter ..............................................................4

3. Connecting Cables and AC Adapter..............................................................6

3-1. Interface Cable .......................................................................................6

3-2. Connecting to a Peripheral Unit.............................................................8

3-3. Connecting the Optional AC Adapter....................................................9

3-4. Turning Power On ...............................................................................10

4. Control Panel and Other Functions.............................................................11

4-1. Control Panel .......................................................................................11

4-2. Errors ...................................................................................................11

4-3. Self Printing .........................................................................................13

5. Loading the Roll Paper .................................................................................14

6. Adjusting the Near-end Sensor ....................................................................17

7. Preventing and Clearing Paper Jams ..........................................................19

7-1. Preventing Paper Jams .........................................................................19

7-2. Removing Paper Jam ...........................................................................19

7-3. Releasing a locked Cutter (Auto Cutter Mode only) ...........................20

8. Periodical Cleaning .......................................................................................22

8-1. Cleaning the Thermal Head .................................................................22

8-2. Cleaning the Paper Holder ...................................................................22

Appendix A: Specifications...............................................................................95

A-1. General Specifications .........................................................................95

A-2. Auto Cutter Specifications ...................................................................96

A-3. Interface ...............................................................................................96

A-4. Electrical Characteristics .....................................................................96

A-5. Option...................................................................................................96

A-6. Environmental Requirements...............................................................97

A-7. Reliability.............................................................................................97

Appendix B: Dip Switch Setting.......................................................................98

B-1. Parallel Interface Type .........................................................................99

B-2. Serial Interface Type..........................................................................101

Appendix C: Parallel Interface ......................................................................104

Appendix D: Serial Interface..........................................................................105

D-1. RS-232C Connector ...........................................................................106

D-2. Cable Connections .............................................................................107

D-3. Electrical Characteristics ...................................................................107

Appendix E: Periheral Unit Drive Circuit ....................................................108

Appendix F: Memory Switch Settings ...........................................................109

Please access the following URL

http://www.star-micronics.co.jp/service/frame_sp_spr_e.htm

for the lastest revision of the manual.

ENGLISH

– 1 –

ENGLISH

1. Parts Identification and Nomenclature

Roll paper User’s manual

Cover open lever

Pull this lever in the

direction of the

arrow to open the

printer cover.

Control panel

Features LED indica-

tors to indicate printer

status and switches to

operate the printer.

Ferrite core Fastener

(Parallel interface

model only) (Parallel interface

model only)

Power switch

Used to turn on/off

power to the printer.

Power connector

For connection of

the AC adapter.

Never unplug the

AC adapter while

the printer is on.

Peripheral drive connector

Connects to peripheral

units such as cash

drawers, etc.

Do not connect this to a

telephone.

Interface connector

For connection to a

host computer.

Printer cover

Open this cover to load or

replace paper.

Auto Cutter Model

– 2 –

ENGLISH

Tear Bar Model

Roll paper User’s manual

Cover open lever

Pull this lever in the

direction of the

arrow to open the

printer cover.

Control panel

Features LED indica-

tors to indicate printer

status and switches to

operate the printer.

Ferrite core Fastener

(Parallel interface

model only) (Parallel interface

model only)

Power switch

Used to turn on/off

power to the printer.

Power connector

For connection of

the AC adapter.

Never unplug the

AC adapter while

the printer is on.

Peripheral drive connector

Connects to peripheral

units such as cash

drawers, etc.

Do not connect this to a

telephone.

Interface connector

For connection to a

host computer.

Printer cover

Open this cover to load or

replace paper.

– 3 –

ENGLISH

Choosing a place for the printer

Before actually unpacking the printer, you should take a few minutes to

think about where you plan to use it. Remember the following points

when doing this.

✓Choose a firm, level surface where the printer will not be exposed to

vibration.

✓The power outlet you plan to connect to for power should be nearby

and unobstructed.

✓Make sure that the printer is close enough to your host computer for

you to connect the two.

✓Make sure that the printer is not exposed to direct sunlight.

✓Makesurethattheprinteriswellawayfromheatersandothersources

of extreme heat.

✓Make sure that the surrounding area is clean, dry, and free of dust.

✓Make sure that the printer is connected to a reliable power outlet. It

should not be on the same electric circuit as copiers, refrigerators, or

other appliances that cause power spikes.

✓Make sure that the room where you are using the printer is not too

humid.

– 4 –

ENGLISH

2. Consumable Parts and AC Adapter

When consumable parts have run out, use those specified in the table below.

Make sure that the AC adapter specified in the table is used.

Use of consumable parts or AC adapter which are not specified in the table may

result in damage to the printer, fire or electric shock.

(1) Roll paper specification

Thermal paper

Thickness: 65~85

Width: 79.5±0.5 mm (57.5±0.5 mm when the optional paper roller

holder is used)

Outer roll diameter: ø90 mm or less

Take up paper roll width: 80 mm or (58 mm when the optional

paper roller holder is used)

Core outer/inner diameter

Paper thickness Core outer Core inner

65~85

m ø18±1 mm ø12±1 mm

Printed surface: Outer edge of roll

Tail end handling: Do not use paste or glue to secure the roll paper or

its core.

Do not fold the tail end of the paper.

(2) Recommended paper

Mitsubishi Paper Mills Limited

P220AG (normal type paper), 65

m (thickness)

HP220A (high image stability paper), 65

m (thickness)

HP220AB-1 (high image stability paper), 75

m (thickness)

P220AB (normal type paper, card ticket), 85

m (thickness)

Oji Paper Co., Ltd.

PD150R (normal type paper), 75

m (thickness)

PD160R (high image stability paper), 65/75

m (thickness)

Nippon Paper Industries

TF50KS-E2C (normal type paper), 65

m (thickness)

Depending on the type and thickness of the paper, it may be necessary to change

the settings for printing darkness. To change the darkness settings, use the

printing darkness settings command <ESC><RS> ‘d’ n. Refer to the separate

programmer’s manual for details.

+0.5

-1 +0.5

-1

– 5 –

ENGLISH

(3) AC adapter (option)

Model name: PS60-24 A

Input: 100 to 240 V AC, 50/60 Hz

Output: DC24±5%, 2.0 A (5.0 A Load 10 sec. Max)

Important!

AccessthefollowingURLfortheinformationoftherecommendedpaper.

http://www.star-micronics.co.jp/

– 6 –

ENGLISH

3. Connecting Cables and AC Adapter

3-1. Interface Cable

3-1-1. Ferrite Core Installation (Parallel interface model only)

(1)Foronlytheparallelinterfacemodel,

affix the ferrite core onto the cable

as shown in the illustration below.

(2)Pass the fastener through the ferrite

core.

(3)Loop the fastener around the cable

and lock it. Use scissors to cut off

any excess.

Ferrite core

Interface cable

5 cm

maximum

Fastener

Pull and cut

– 7 –

ENGLISH

3-1-2. Connecting the Interface Cable

Note: Before connecting/disconnecting the interface cable, make sure that

power to the printer and all the devices connected to the printer is

turned off.

Alsomakesurethepowercableplugisdisconnectedfromthe

AC outlet.

(1)Connect the interface cable to the connector on the rear panel of the printer.

(2)In the case of a serial interface, tighten the connector screws. In the case of a

parallel interface, fasten the connector clasps.

Serial interface cable

Parallel interface cable

Andere Handbücher für TSP600 Series

Inhaltsverzeichnis

Sprachen:

Andere Star Micronics Drucker Handbücher

Star Micronics

Star Micronics SP500 Series Bedienungsanleitung

Star Micronics

Star Micronics LC-7211 Bedienungsanleitung

Star Micronics

Star Micronics NX-1020 Bedienungsanleitung

Star Micronics

Star Micronics SP500 Series Montageanleitung

Star Micronics

Star Micronics TSP1000 Series Handbuch

Star Micronics

Star Micronics TSP700II Series Bedienungsanleitung

Star Micronics

Star Micronics USB Bedienungsanleitung

Star Micronics

Star Micronics NP-255 Montageanleitung

Star Micronics

Star Micronics SLIP SP298 SERIES Bedienungs- und Wartungshandbuch

Star Micronics

Star Micronics Star DP8340 Bedienungsanleitung

Star Micronics

Star Micronics SP500 Series Bedienungsanleitung

Star Micronics

Star Micronics NX-1040 Bedienungsanleitung

Star Micronics

Star Micronics LC24-200 Colour Bedienungsanleitung

Star Micronics

Star Micronics SLIP SP298 SERIES Bedienungsanleitung

Star Micronics

Star Micronics TSP200 Series Bedienungsanleitung

Star Micronics

Star Micronics Rainbow NX-1000C Bedienungsanleitung

Star Micronics

Star Micronics SB-10 Bedienungsanleitung

Star Micronics

Star Micronics Star SCP700 Series Bedienungsanleitung

Star Micronics

Star Micronics TSP800 Series Bedienungsanleitung

Star Micronics

Star Micronics TSP100IIIU Montageanleitung

Star Micronics

Star Micronics LaserPrinter 8III Bedienungsanleitung

Star Micronics

Star Micronics MULTI-FONT NX-1000II Bedienungsanleitung

Star Micronics

Star Micronics NL-10 Bedienungsanleitung

Star Micronics

Star Micronics TSP700II Series Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung