Star Micronics TSP700II Series Bedienungsanleitung

THERMAL PRINTER

TSP700II SERIES

Hardware Manual

Federal Communications Commission

Radio Frequency Interference

Statement

is device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is

subject to the following two conditions:

(1) is device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.

L'exploitation est autorisée aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d'en compromettre le fonctionnement.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

For compliance with the Federal Noise Interference Standard, this equipment requires a shielded cable.

For RF interference suppression, if a ferrite core is provided with this device, ax it to the interface cable.

NOTE:

is equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 of the FCC Rules. ese limits are designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and

meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio

frequency (RF) Exposure rules. is equipment has very low levels of RF energy that it deemed to comply without

maximum permissive exposure evaluation(MPE). But it is desirable that it should be installed and operated keeping

the radiator at least 20cm or more away from person's body (excluding extremities: hands,wrists,feet and ankles).

Cet équipement est conforme aux limites d"exposition aux rayonnements énoncées pour un environnement non

contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices d'exposition dans le Supplément

C à OET65 et d"exposition aux fréquences radioélectriques (RF) CNR-102 de l"IC. Cet équipement émet une

énergie RF très faible qui est considérée conforme sans évaluation de l"exposition maximale autorisée. Cependant,

cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le dispositif rayonnant et

le corps (à l"exception des extrémités : mains, poignets, pieds et chevilles).

Trademark acknowledgments

TSP700II : Star Micronics Co., Ltd.

Notice

permission is forbidden.

•e contents of this manual are subject to change without notice.

•All eorts have been made to ensure the accuracy of the contents of this manual at the time of going to press.

However, should any errors be detected, STAR would greatly appreciate being informed of them.

•e above notwithstanding, STAR can assume no responsibility for any errors in this manual.

•iOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.

•Android is a trademark of Google Inc.

•Windows is registered trademarks of Microso Corporation.

•Bluetooth® wordmark and logo are registered trademarks owned by Bluetooth SIG, Inc.

2007-2016 Star Micronics Co., Ltd..

Caution Symbol

ese symbols are located near the thermal print head.

Because the thermal print head is hot immediately aer printing, do not touch it. Static

electricity can damage the thermal print head. To protect the thermal print head from

static electricity, do not touch it.

is symbol is located near the cutter.

Never touch the cutter blade, as you could injure your ngers.

is symbol is located near the peripheral drive connector.

Do not connect this to a telephone.

is symbol is located near the screws securing the case or the protective plate, which

should not be opened by individuals other than service personnel. Individuals, other

than service personnel, should not remove these screws. High voltage areas in the case

can be dangerous.

TABLE OF CONTENTS

1. Unpacking and Installation................................................................................. 5

1-1. Unpacking................................................................................................ 5

1-2. Notes about Installation ........................................................................... 5

2. Parts Identication and Nomenclature............................................................... 6

3. Setup .................................................................................................................... 7

3-1. Connecting the Interface Cable to the PC ................................................. 7

3-2. Connecting the Interface Cable to the Printer��8

3-3. Connecting the AC Adapter.................................................................... 11

3-4. Turning the Power On ............................................................................ 12

3-5. Connecting to a Peripheral Device.......................................................... 12

3-6. Loading a Paper Roll .............................................................................. 13

3-7. Bluetooth Settings (For Bluetooth Interface Models only).............................. 17

3-8. Setup Precautions................................................................................... 22

4. Attaching the Accessories....................................................................................24

4-1. Attaching the Holder Plate ..................................................................... 24

4-2. Attaching the Cable................................................................................ 27

4-3. Switch Blind Installation ........................................................................ 27

5. Error Indicators ..................................................................................................28

5-1. Recoverable errors.................................................................................. 28

5-2. Unrecoverable errors.............................................................................. 28

6. Preventing and Clearing Paper Jams ..................................................................29

6-1. Preventing Paper Jams............................................................................ 29

6-2. Removing Paper Jam .............................................................................. 29

7. Maintenance ........................................................................................................30

7-1. Thermal Head ........................................................................................ 30

7-2. Platen Rubber Roller .............................................................................. 30

7-3. Sensors and the Surrounding Areas ........................................................ 30

7-4. Paper Holder the Suurounding Areas...................................................... 30

1-1. Unpacking

Aer unpacking the unit, check that all the necessary accessories are included in the package.

* Accessories vary depending on the model and the region where the printer was purchased.

1. Unpacking and Installation

1-2. Notes about Installation

1. Choose a rm, level surface where the printer will not be exposed to vibration.

2. Make sure that the printer is connected to a reliable power outlet. It should not be on the same electric circuit as copi-

ers, refrigerators, or other appliances that cause power spikes.

3. e power outlet you plan to connect to for power should be nearby and unobstructed.

4. Make sure that the printer is not exposed to direct sunlight.

5. Make sure that the printer is well away from heaters and other sources of extreme heat.

6. Do not locate the printer in a badly ventilated or dusty environment.

7. Make sure that the room where you are using the printer is not too humid.

8. is device employs a DC motor and switches that have an electrical contact point.

Avoid using the device in environments where silicon gas can become volatile.

9. Use the printer within the boundaries indicated in the environmental requirements. Even when the ambient tem-

perature and humidity are within the specications, avoid radical changes in environmental conditions. e suitable

operating temperature range is as follows:

Operating temperature: 5°C to 45°C

10. When disposing of the printer, obey local regulations.

Note: The ferrite core and fastener provided with your printer depend on your

printer conguration.

Printer

Cable cover

Holding plate

Screws

Roll stoppers

Shaft

Paper roll Switch blind Setup sheets

2. Parts Identication and Nomenclature

Interface connector

For connection to a

host computer.

Peripheral drive connector

Connects to peripheral units

such as cash drawers, etc.

Do not connect this to a

telephone.

Power connector

For connection of the AC

adapter.

Never unplug the AC adapter

while the printer is on.

Printer cover

Open this cover to load

or replace paper.

Cover open lever

Push this lever in the direction of the ar-

row to open the printer cover.

Power switch

Used to turn on/

o power to the

printer.

Control panel

Features LED indicators to indi-

cate printer status and switches

to operate the printer.

Lights when the printer is online.

This lamp also indicates errors, in combination with ERROR lamp.

POWER lamp (green)

Lights when the cover is open.

This lamp also indicates errors, in combination with POWER lamp.

ERROR lamp (Red/Orange LED)

When the printer is online, pressing this button feeds the paper roll.

FEED button

3-1. Connecting the Interface Cable to the PC

3-1-1. Parallel Cable

Connect the parallel cable to a parallel port on your PC.

3-1-2. RS-232C Cable

Connect the RS-232C cable to a RS-232C port on your PC.

3-1-3. USB Cable

Connect the USB cable to a USB port on your PC.

3-1-4. Ethernet Cable

Connect the Ethernet cable to a USB port on your PC.

3. Setup

3-2. Connecting the Interface Cable to the Printer

Printer cables are not included in the package.

Obtain an appropriate cable that complies with the specications beforehand.

Because the appropriate interface cable diers depending on the system that you are connecting the printer to, contact

the dealer that you bought the product from if you are unsure about what cable to use.

Before connecting or disconnecting an interface cable, be sure to disconnect the AC adapter’s power cord

from the outlet.

3-2-1. Parallel Interface Cable

To connect a parallel cable, follow the procedure given below.

(1) Make sure the printer is turn o.

(2) Ax the ferrite core onto the cable as shown in the illustration.

(3) Pass the fastener through the ferrite core.

(4) Loop the fastener around the cable and lock it. Use scissors to cut

o any excess.

(5) Connect the interface cable to the connector on the rear panel of

the printer.

(6) Fasten the connector clasps.

Ferrite core

Interface cable

5 cm

(maximum)

Fastener

Pull and cut

Parallel interface cable

3-2-2. RS-232C Interface Cable

(1) Make sure that the AC adapter’s power cord is not connected to the outlet.

(2) Connect the interface cable to the connector on the rear panel of the printer.

(3) Tighten the connector screws.

3-2-3. USB Cable

To connect a USB cable, follow the procedure given below.

(1) Make sure that the AC adapter’s power cord is not connected to the outlet.

(2) Connect the USB cable to the USB port.

(3) As shown in the gure, pass the cable through the cable hooks to hold it in place.

RS-232C interface cable

4 cm (maximum)

USB cable

Cable hook

3-2-4. Ethernet Cable

If a ferrite core is included, install the ferrite core onto the Ethernet cable according to the following procedure to

prevent electrical noise.

If a ferrite core is not included, perform steps (1) and (5) only.

When using an Ethernet cable that is 10 cm or less, shielded cable is recommended.

g Link disconnection detection feature

e Ethernet interface model is equipped with a link disconnection detection feature.

If the printer is turned on when an Ethernet cable is not connected to it, the POWER and ERROR lamps are simul-

taneously turned on and o at 4-second intervals to indicate the disconnection.

Be sure to connect the Ethernet cable from a PC or hub to the printer, and then turn the printer on.

(1) Make sure the printer is turned o.

(2) Install the ferrite core onto the ethernet cable as shown in the illustration below.

(3) Pass the fastener through the ferrite core.

(4) Loop the fastener around the cable and lock it. Use scissors to cut o any excess.

(5) Connect the interface cable to the connector on the rear panel of the printer.

Ethernet cable

IFBD-HE07

10 cm

(maximum)

Fastener

Ferrite core

Ethernet cable

IFBD-HE05

Andere Handbücher für TSP700II Series

Inhaltsverzeichnis

Andere Star Micronics Drucker Handbücher

Star Micronics

Star Micronics LC-500 Bedienungsanleitung

Star Micronics

Star Micronics TSP400 Series Bedienungsanleitung

Star Micronics

Star Micronics DP8340R Series Bedienungsanleitung

Star Micronics

Star Micronics TSP400 Series Bedienungsanleitung

Star Micronics

Star Micronics TSP143IIU Bedienungsanleitung

Star Micronics

Star Micronics LaserPrinter4 Bedienungsanleitung

Star Micronics

Star Micronics DP-8340 FM-120 Bedienungsanleitung

Star Micronics

Star Micronics SP320S series Bedienungsanleitung

Star Micronics

Star Micronics lC-10 Bedienungsanleitung

Star Micronics

Star Micronics TSP552 Bedienungsanleitung

Star Micronics

Star Micronics SP500 Series Montageanleitung

Star Micronics

Star Micronics LC-1011C Bedienungsanleitung

Star Micronics

Star Micronics LC-100+ Bedienungsanleitung

Star Micronics

Star Micronics LC-90 Bedienungsanleitung

Star Micronics

Star Micronics 8111 Gebrauchsanweisung

Star Micronics

Star Micronics TSP700 Series Bedienungsanleitung

Star Micronics

Star Micronics Star SCP700 Series Bedienungs- und Wartungshandbuch

Star Micronics

Star Micronics SP700 Series Bedienungsanleitung

Star Micronics

Star Micronics LaserPrinter 8III Bedienungsanleitung

Star Micronics

Star Micronics Rainbow NX-1000C Bedienungsanleitung

Star Micronics

Star Micronics SP317/347F Bedienungsanleitung

Star Micronics

Star Micronics NX-1000 Bedienungsanleitung

Star Micronics

Star Micronics LC24-200 Colour Bedienungsanleitung

Star Micronics

Star Micronics DP8340 Series Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Brother

Brother 1440 - HL B/W Laser Printer Kurzanleitung

Fuji Xerox

Fuji Xerox DocuPrint P375 dw Bedienungsanleitung

WOOSIM

WOOSIM PORTI-S30 Bedienungsanleitung

Olivetti

Olivetti PG L2140 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub 224e Bedienungsanleitung

Canon

Canon LBP113w Bedienungsanleitung

Xerox

Xerox DocuColor 5000 Bedienungsanleitung

Canon

Canon PRO-500 Series Einrichtungshandbuch

Epson

Epson ET-7750 Betriebsanleitung