StarTech.com ST1000BT32 Handbuch

10/100/1000 Mbits/sec PCI Gigabit

Ethernet Adapter

ST1000BT32

ST1000BT64 Instruction Guide

The Professionals’ Source For Hard-to-Find Computer Parts

GIGABIT EETHERNET

ADAPTER

* Actual product may vary from photo

* ST1000BT32 shown

FCC COMPLIANCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installing the Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Introduction

Thank you for purchasing a StarTech.com Gigabit Ethernet adapter. Now your network

can experience incredibly fast data transfer speeds of up to 1000 Mbits/sec. With it’s

auto-sensing and auto-negotiation features, this card is also backwards-compatible with

100 Mbits/sec Fast Ethernet and 10 Mbits/sec Ethernet speeds and is capable of both

full- and half-duplex communications.

The ST1000BT64 is compliant with both 64-bit and 32-bit PCI specifications. The

ST1000BT32 is compliant with 32-bit PCI specifications.

Features

•Supports 64/32-bit (ST1000BT64) or 32-bit (ST1000BT32) 66/33 MHz PCI Local Bus

Master Version 2.2/2.1

•Complies with IEEE 802.3, IEEE 802.3u, and IEEE 802.3ab specifications

•Supports IEEE 802.3x full-duplex flow control

•Supports Plug and Play installation and automatic IRQ and I/O address setup

•Supports Jumbo Packet

•Built-in FIFO buffers reduce memory transfer overhead

•Backed by StarTech.com’s lifetime warranty

Before You Begin

To ensure a quick and easy card installation, please read the following section before

installing your card.

System Requirements

•APC and BIOS that supports PCI Local Bus Specification v2.0 or higher (Make sure

that your BIOS is updated) running Windows XP, 2000, NT, Me, 98, 95 OSR2, Netware

Server 5.x, Linux

•An available bus-mastering 32- or 64-bit PCI slot

•Cat 5e (or higher) UTP cable (for best results)

Contents

This package should contain:

•1x PCI Gigabit Ethernet network adapter

•1x driver disk

Installation

This section will guide you through the installation of your card and the related

software. Please read through the instructions carefully and complete each step in the

order listed.

Installing the Card

1. Make sure that your computer power cord is unplugged and you are grounded.

2. Remove the cover of your system (see your computer's user manual for details, if

necessary) and gently turn your computer onto its side.

3. Locate an empty PCI slot (usually white in colour, a 64-bit slot will be longer than a

32-bit slot) and remove the metal plate that covers the rear bracket. You may need a

Phillips screwdriver to perform this step. Hang on to the screw! You will need it to

secure the card later.

4. Gently insert the card into the empty slot, making sure it is firmly seated.

NOTE: If you are using the ST1000BT64-bit card in a 32-bit slot, make sure that the

exposed end of the card is not in contact with any conducting parts on your

motherboard. Not all motherboards allow 64-bit cards to fit into 32-bit slots.

5. Secure the card in place using the screw you removed in Step 3.

6. Put the computer case back on.

7. Plug the computer power cord back into an appropriate power source.

Installing the Drivers

NOTE: The following instructions are for Windows users only. Linux or Netware users

should consult the Readme.txt files in their respective folders. Depending on your OS

and the configuration of your system, the instructions below may not be identical to the

instructions on your screen.

Windows XP/2000/98/Me

1. Windows will automatically detect the new hardware. Click Next.

2. Select "Search for the best driver for your device (Recommended)” and click Next.

3. Insert your driver disk into the disk drive, browse to the WinXP, Win2000, WinMe, or

Win98 folder on the disk drive, then click Next.

4. Click Next. Windows will now install the driver.

5. When the download is complete, click Finish. If prompted, choose to restart your

system.

Windows 95B

1. Windows will automatically detect the new hardware. Select “Driver from disk

provided by hardware manufacturer” and click OK.

2. Insert the driver disk into the disk drive. Browse to the Win95B folder on the driver

disk and click OK. You may be required to provide your Windows 95 installation

disk.

3. When all drivers have been installed, reboot your computer to initialize the network

function.

Windows NT 4

1. Click on Start, then Settings, then Control Panel.

2. Click on the Network icon.

3. In the Network Settings box, choose “Add Adapter.”

4. Select “<Other> Requires disk from manufacturer” and press Enter.

5. Insert the drive disk into your disk drive. Browse to the WinNT4 folder on the driver

disk and click OK.

6. Windows NT will begin the binding process. If any additional network software

options were installed, you may be prompted for specific information about these

packages.

7. When installation is complete, restart your computer.

Monitoring Your Card

The card uses three Link/Activity LEDs to indicate the connection rate and activity of

the card. The three LEDs are for 10, 100, or 1000 Mbits/sec. A solid LED indicates that a

link has been established at that rate. A blinking LED indicates that there is traffic flow

on the network.

If no Link/Activity LED is lit, there is a connection error. Make sure that all devices are

turned on and that the network cable is properly connected at both ends. Also make sure

that your network cables comply with EIA/TIA 568 and at least Cat 5e specifications.

If problems persist, power down all devices and disconnect all plugs. Wait at least ten

seconds then plug the devices back in and power them up.

Connecting Your Card to Your Network

Depending on how you are planning on using the card, the device you are connecting it

to and the type of cable you need may differ. To take advantage of the card’s Gigabit

(1000 Mbits/sec) capacity, it is recommended that you always use at least Cat. 5e

Ethernet cable. If you are unsure of the type of cable required for your device, consult

your device manufacturer.

NOTE: StarTech.com carries a wide range of Cat. 5e and Cat. 6 Ethernet cables in various

colors and lengths. For more information on these products, as well as tips and ideas for

setting up and running your network, visit http://www.startech.com and click on the

Networking tab near the top of the screen.

•If you are connecting your computer directly to another computer, you need to use a

crossover cable.

•If you are connecting your computer to a hub or switch, you should use a straight-

through cable.

•If you are connecting your computer to the Internet via a DSL or cable modem, you

should use the cable recommended by the modem manufacturer.

Tips for Setting Up Your Network

For information and help on setting up your network, please consult the manufacturer of

your operating system. The following is for tips and troubleshooting purposes only and

is intended for Microsoft users on a local area network.

Make sure your computers are configured properly

For your convenience, you should configure each of your computers so that they can

“see” each other and share devices and files. To do this, you have to make sure that the

following have been installed on your computers:

•Client for Microsoft Networks

•TCP/IP (Internet Protocol)

•File and Print Sharing

These clients, protocols, and services can be found in the following locations:

Windows XP

1. Click on Start, then click My Network Places.

2. Click View Network Connections in the Network Tasks box.

3. Right-click on Local Area Connection and choose Properties.

Windows 2000

1. Click on Start, then Settings, then Network and Dialup Connections.

2. Double-click Local Area Connections and click the Properties button.

Windows Me/98/95

1. Click on Start, then Settings, then Control Panel.

2. Double-click on Network.

NOTE: If you need to add any of the following components, check your Windows

documentation for details.

Make sure all your computers are on the same workgroup

To be able to communicate properly with each other, each computer must be located on

the same workgroup. Each computer within a workgroup must have a unique name. To

ensure compatibility between each version of Windows, keep your computer names

under 13 characters long. To view, add, or edit your computer’s name, do the following:

Windows XP

1. Click Start and then Control Panel.

2. Double-click System then click on the computer name tab.

Windows 2000

1. Click on Start, then Settings, then Control Panel.

2. Double-click on System.

3. Click on the Network Identification tab.

Windows Me/98/95

1. Click Start, then Settings, then Control Panel.

2. Double-click Network, then click the Identification tab.

Make Sure Your Sharing is Set Up Properly

1. Go to your network dialog box using the procedure explained under “Make sure

your computers are configured properly.”

2. Click on File and Print Sharing.

3. Choose whether you want to install one, both, or neither of these options. Click OK.

4. Decide what files or folders you want to share. You can call up sharing options by

right-clicking on a file or folder and choose “Sharing” (Windows 2000/Me/98/95) or

“Sharing and Security” (Windows XP).

NOTE: If you are having any difficulties setting up or using your network, please

contact your operating system vendor.

Technical Specifications

Connector RJ-45

Standard IEEE 802.3 10BaseT

IEEE 802.3u 100BaseTx

IEEE 802.3ab 1000BaseT

Transmission Rate 10/20 (half/full duplex)

(Mbits/sec) 100/200 (half/full duplex)

1000/2000 (half/full duplex)

IRQ Line Assigned by system

I/O Address Assigned by system

Drivers Windows 95 OSR2/98/NT/Me/2000/XP,

Netware Server 5.x, Linux

LEDs 10 Mbits/sec Link/Activity

100 Mbits/sec Link/Activity

1000 Mbits/sec Link/Activity

Temperature 31~131ºF (0~55ºC)

Humidity 10~95% (non-condensing)

Certification FCC Class B, CE Mark, C-tick

Technical Support

The following technical resources are available for this StarTech.com product:

On-line help:

We are constantly adding new information to the Tech Support section of our web site. To

access this page, click the Tech Support link on our homepage, www.startech.com. In the

tech support section there are a number of options that can provide assistance with this

card.

Knowledge Base - This tool allows you to search for answers to common issues using

key words that describe the product and your issue.

FAQ - This tool provides quick answers to the top questions asked by our customers.

Downloads - This selection takes you to our driver download page where you can

find the latest drivers for this product.

Call StarTech.com tech support for help: 1-519-455-4931

Support hours: Monday to Friday 9:00AM to 5:00PM EST (except holidays)

Warranty Information

This product is backed by a lifetime warranty. In addition, StarTech.com warrants its

products against defects in materials and workmanship for the periods noted below,

following the initial date of purchase. During this period, the products may be

returned for repair, or replacement with equivalent products at our discretion. The

warranty covers parts and labor costs only. StarTech.com does not warrant its products

from defects or damages arising from misuse, abuse, alteration, or normal wear and

tear.

Limitation of Liability

In no event shall the liability to StarTech.com Ltd. (or its officers, directors, employees or

agents) for any damages (whether direct or indirect, special, punitive incidental,

consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss,

arising out of related to the use of the product exceed the actual price paid for

the product.

Some states do not allow the exclusion or limitation of incidental or consequential

damages. If such laws apply, the limitations or exclusions contained in this statement

may not apply to you.

Andere Handbücher für ST1000BT32

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere StarTech.com Adapter Handbücher

StarTech.com

StarTech.com USB31000S Bedienungsanleitung

StarTech.com

StarTech.com ECUSB3S2 Bedienungsanleitung

StarTech.com

StarTech.com USB2IR2 Bedienungsanleitung

StarTech.com

StarTech.com CB555WG Handbuch

StarTech.com

StarTech.com USB2VGAPRO Bedienungsanleitung

StarTech.com

StarTech.com DKT30CHVSCPD Bedienungsanleitung

StarTech.com

StarTech.com DVI2DPA Bedienungsanleitung

StarTech.com

StarTech.com ICUSB232IS Bedienungsanleitung

StarTech.com

StarTech.com CDP2HD4K60SA Bedienungsanleitung

StarTech.com

StarTech.com PCIVGA7 Bedienungsanleitung

StarTech.com

StarTech.com ICUSB422 Bedienungsanleitung

StarTech.com

StarTech.com ZIF2IDE35 Bedienungsanleitung

StarTech.com

StarTech.com EOC110K Bedienungsanleitung

StarTech.com

StarTech.com ECUSB3S2 Bedienungsanleitung

StarTech.com

StarTech.com DP2DVID Bedienungsanleitung

StarTech.com

StarTech.com NOTECONS01 Bedienungsanleitung

StarTech.com

StarTech.com EC1PECPS Systemhandbuch

StarTech.com

StarTech.com USB433ACD1X1 Bedienungsanleitung

StarTech.com

StarTech.com 8ST115BUSBCMULTI Bedienungsanleitung

StarTech.com

StarTech.com PEX433WAC11 Bedienungsanleitung

StarTech.com

StarTech.com USB2100S Handbuch

StarTech.com

StarTech.com USBBT2EDR4 Bedienungsanleitung

StarTech.com

StarTech.com 109B-USBC-HDMI Bedienungsanleitung

StarTech.com

StarTech.com USBBT1EDR2 Bedienungsanleitung

Beliebte Adapter Handbücher anderer Marken

PCB Piezotronics

PCB Piezotronics 090B274 Bedienungsanleitung

Auvidea

Auvidea J20 Produkthandbuch

Gossen MetraWatt

Gossen MetraWatt AT3-III E Bedienungsanleitung

Akribis

Akribis ITF-21-BISS-MIT Bedienungsanleitung

Tenda

Tenda W54U Bedienungsanleitung

ROHO

ROHO AGILITY Bedienungsanleitung

PROLiNK

PROLiNK WN2001 Bedienungsanleitung

Hawking

Hawking HUF2 Bedienungsanleitung

Airlink101

Airlink101 AWLC4030 Bedienungsanleitung

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Bedienungsanleitung

Philips

Philips SWA4554S/10 Bedienungsanleitung

JVC

JVC TS-C9D2B Gebrauchsanweisung

NETGEAR

NETGEAR A6100 Bedienungsanleitung

D-Link

D-Link DWA-121 Bedienungsanleitung

Philips

Philips SWA2037 Bedienungsanleitung

Basalte

Basalte 0610-20 Bedienungsanleitung

Yealink

Yealink EHS40 Bedienungsanleitung

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Bedienungsanleitung