StarTech.com UNIDOCKU33 Bedienungsanleitung

Manual Revision: 10/28/2014

For the most up-to-date information, please visit: www.startech.com

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

IT: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

UNIDOCKU33

USB 3.0 SATA or IDE HDD/SSD Dock w/ UASP

*actual product may vary from photos

Instruction Manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved by StarTech.com could void the user’s

authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of

their respective holders.

Instruction Manual

Table of Contents

Introduction............................................................................................1

Packaging Contents ................................................................................................................................. 1

System Requirements.............................................................................................................................. 1

Product Diagram ....................................................................................2

Front View .................................................................................................................................................... 2

Rear View .................................................................................................2

Docking Station Installation.................................................................3

SATA Drive Installation..........................................................................3

IDE Drive Installation.............................................................................4

SATA/IDE Drive Removal .......................................................................4

Docking Station Operation...................................................................5

Drive Initialization .................................................................................................................................... 5

LED Indicators.........................................................................................6

Disconnecting the Hard Drive.............................................................................................................. 6

Specications..........................................................................................8

Technical Support ..................................................................................9

Warranty Information............................................................................9

Instruction Manual

Introduction

Packaging Contents

• 1x Universal Hard Drive Dock

• 1x USB 3.0 Cable

• 1x IDE 40 to 40 Pin Cable

• 1x LP4 Power Cable

• 1x 40 Pin + LP4 to 44 Pin IDE Cable

• 1x Universal Power Adapter (NA/UK/EU/AUS)

• 1x Instruction Manual

System Requirements

• Computer system with available USB port

• 2.5” / 3.5” SATA and/or IDE Hard Drive (HDD) or Solid State Drive (SSD)

Instruction Manual

Product Diagram

Front View

1. SATA Hard Drive Power button / Power and Activity LED (Button #1)

2. IDE Hard Drive Power button / Power and Activity LED (Button #2)

3. SATA Hard Drive slot (Slot #1)

4. IDE Hard Drive slot (Slot #2)

5. SATA Hard Drive eject button

Rear View

1. IDE Hard Drive Data Port

2. IDE Hard Drive Power port

3. USB 3.0 port

4. Power adapter port

Instruction Manual

Docking Station Installation

WARNING:

Hard drives and docking stations require careful handling. If you are not careful with

your hard disk, lost data may result. Always handle your hard drive and docking station

with caution. Be sure that you are properly grounded by wearing an anti-static strap

when handling computer components or discharge yourself of any static electricity

build-up by touching a large grounded metal surface (such as the computer case) for

several seconds.

1. Connect the Dock to an available power outlet, using the provided power adapter.

2. Connect the Dock to your computer system, using the provided USB 3.0 cable.

SATA Drive Installation

1. Carefully align and insert your 2.5” or 3.5” SATA drive in the SATA Hard Drive slot (slot

#1) on the docking station, such that the SATA power and data connectors on the

drive are properly aligned with the corresponding connectors inside the hard drive

slot.

2. Press the SATA Hard Drive power button.

3. Your computer Operating System will now automatically recognize the drive and it

will be accessible as though it were installed in the system internally.

Note: If your computer fails to automatically recognize your drive it is likely your drive

has not been initialized or formatted correctly. (See Drive Initialization in Software

operation for further instructions.)

Instruction Manual

IDE Drive Installation

1. Connect the included 40-pin IDE ribbon cable to the IDE connector on the rear of

the dock. If using a 2.5in IDE hard drive, connect the 40 to 44-pin IDE cable to the

rear of the dock.

2. Connect the included LP4 Molex power cable into the LP4 connector on the rear

of the dock. If using the 40 to 44-pin cable, connect the built-in LP4 connector to

the connector on the rear of the dock.

3. Connect the IDE hard drive to the ribbon cable and LP4 Molex connector (3.5in

only). Make sure all of the cables are securely connected.

4. Insert the IDE hard drive into the top-loading drive bay (closest to rear connectors).

5. Press the IDE Hard Drive power button.

Note: If your computer fails to automatically recognize your drive it is likely your drive

has not been initialized or formatted correctly. (See Drive Initialization in Software

operation for further instructions.)

SATA/IDE Drive Removal

WARNING:

Ensure your hard drive(s) has been disconnected from your computer operating

system prior to attempting drive removal. Failure to properly disconnect your drive

may result in lost data or drive damage. (See Disconnecting the Hard Drive in Docking

Station Operation for further instructions.)

1. Turn o your drive by pressing the corresponding power button.

2. (Only required for IDE drives) If you have a 3.5in IDE drive, disconnect the 40pin IDE cable

and the LP4 power cable (3.5in drive) from both your hard drive and the docking station.

Instruction Manual

If you have a 2.5in IDE drive, disconnect the 44-pin IDE cable from the drive, and

disconnect the 40 pin IDE cable and LP4 breakout cable from the docking station.

3. (Only required for SATA drives) Press the eject button for the SATA Hard drive to

release the drive from the connector for removal.

4. Carefully grasp the drive and lift it upwards until the bottom of the drive has

completely risen above the hard drive slot.

5. Safely and carefully store your drive and any cables in a secure location. (See your

hard drive manual for proper storage instructions.)

Docking Station Operation

Drive Initialization

Prior to using your installed drive, it will need to be initialized and formatted to the

operating system requirements in order for your computer system to recognize it.

1. From the main Windows desktop, right-click on “My Computer” (“Computer” in

Vista/ 7 / 8/ 8.1), then select Manage. In the new Computer Management window,

select Disk Management from the left window panel.

Instruction Manual

2. A dialog window will automatically appear, asking you to initialize the drive.

Depending on the version of Windows, it will give you the option of either creating

an “MBR” or “GPT” disk.

Note: GPT (GUID partition) is required for drives larger that 2TB but is not compatible

with some older operating systems, while MBR is supported by newer and older

operating systems.

3. Once initialized, locate the Disk that says it is “Unallocated” (check the listed hard

drive capacity to conrm it’s the correct hard drive) and then right-click in the

section that says “Unallocated” and select “New Partition”.

4. Follow the on screen prompts to initialize the drive in the format of your choice.

LED Indicators

The docking station oers a power LED indicator (blue) and an activity LED indicator

(red) for each drive. When the drive is powered on, the Blue LED Power indicator

will illuminate. While the hard drive is being accessed, the Red LED will ash. Do not

remove your drive from the docking station while the Red LED is ashing, as it could

damage to your drive, resulting in data loss.

Disconnecting the Hard Drive

Windows

1. Select the “Safely remove Hardware and Eject Media” icon, located in the task bar.

2. Select the storage device from the list that appears.

3. Wait for the message indicating that it is now safe to remove the device.

Note: Removing the connected drive prior to receiving notication that it is safe to

do so, could result in losing or corrupting data stored on the drive. Once the Safe

to Remove Hardware message appears, please remove the drive from the docking

station. (See Drive Removal.)

Instruction Manual

Mac OS X

To safely disconnect the attached drive from the host computer, close any windows

listing the contents of the removable drive. Once all windows are closed, click on the

USB storage icon on the desktop, and drag it to the Trash Can icon on the desktop.

Allow 5 seconds before physically removing the drive from the docking station.

Inhaltsverzeichnis

Andere StarTech.com Dockingstation Handbücher

StarTech.com

StarTech.com ST4300U3C1 Bedienungsanleitung

StarTech.com

StarTech.com DK30A2DHU Bedienungsanleitung

StarTech.com

StarTech.com Thunderbolt TB3CDOCKDP Bedienungsanleitung

StarTech.com

StarTech.com TB3DK2DPW Bedienungsanleitung

StarTech.com

StarTech.com USB3SMDOCKV Bedienungsanleitung

StarTech.com

StarTech.com DK31C4DPPD Bedienungsanleitung

StarTech.com

StarTech.com DK30C2DPPDUE Bedienungsanleitung

StarTech.com

StarTech.com USB3DOCKH2DP Bedienungsanleitung

StarTech.com

StarTech.com TB3DK2DPWUE Bedienungsanleitung

StarTech.com

StarTech.com TB3DK2DPM2 Bedienungsanleitung

StarTech.com

StarTech.com SATDOCK25U Bedienungsanleitung

StarTech.com

StarTech.com SATDOCK22RE Bedienungsanleitung

StarTech.com

StarTech.com SATADOCKU2 Bedienungsanleitung

StarTech.com

StarTech.com TB3DKM2HDL Bedienungsanleitung

StarTech.com

StarTech.com 8STSDOCK1EU3P2 Bedienungsanleitung

StarTech.com

StarTech.com SATDOCK22U3S Bedienungsanleitung

StarTech.com

StarTech.com USB3VDOCKD Bedienungsanleitung

StarTech.com

StarTech.com USB3SDOCKDD Bedienungsanleitung

StarTech.com

StarTech.com DK30CHDDPPD Bedienungsanleitung

StarTech.com

StarTech.com DK30CH2DEPUE Bedienungsanleitung

StarTech.com

StarTech.com Thunderbolt TB3CDOCKDP Bedienungsanleitung

StarTech.com

StarTech.com SATDOCKU3SEF Bedienungsanleitung

StarTech.com

StarTech.com USB3SDOCKDD Bedienungsanleitung

StarTech.com

StarTech.com DKM31C3HVCPD Bedienungsanleitung

Beliebte Dockingstation Handbücher anderer Marken

Sony

Sony Dream Machine XDR-DS12iP Bedienungsanleitung

Acer

Acer USB Type-C Dock II Bedienungsanleitung

ATEN

ATEN UC-2000 Bedienungsanleitung

Xcellon

Xcellon HDD-202 Bedienungsanleitung

Dok

Dok CR09 Bedienungsanleitung

Philips

Philips BTM630/12 Bedienungsanleitung

IOGear

IOGear Travel Pro GUD3C09 Bedienungsanleitung

RKI

RKI SDM-E2 Bedienungsanleitung

iHome

iHome iP15 Bedienungsanleitung

VITURE ONE

VITURE ONE MOBILE DOCK Bedienungsanleitung

Lindy

Lindy 42984 Bedienungsanleitung

CipherLab

CipherLab 8001 Bedienungsanleitung

Pyle

Pyle PIPDSP2 Bedienungsanleitung

Avol

Avol AS2350 Bedienungsanleitung

Datalogic

Datalogic JoyaTouch Bedienungsanleitung

Philips

Philips DC190/79 Bedienungsanleitung

Targus

Targus DOCK315EUZ Bedienungsanleitung

Akasa

Akasa DuoDockX3 AK-DK08U3-BK Bedienungsanleitung