StarTech.com SDOCK1EU3P Bedienungsanleitung

Manual Revision: 11/27/2015

For the latest information, technical specications, and support for

this product, please visit www.startech.com/SDOCK1EU3P.

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

IT: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

SDOCK1EU3P

Standalone Hard Drive Eraser & USB 3.0 Dock

*actual product may vary from photos

Instruction manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved by StarTech.com could void the user’s

authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of

their respective holders.

Instruction manual

Table of Contents

Product diagram ....................................................................................1

Introduction............................................................................................2

Packaging contents.................................................................................................................................. 2

About the LED indicators ....................................................................................................................... 3

Erasing a drive ........................................................................................4

Erase a drive ................................................................................................................................................ 5

Erase a drive using customized settings........................................................................................... 5

Change the custom erase settings ..................................................................................................... 6

Using the Utility menu ..........................................................................7

View the eraser details ............................................................................................................................ 7

Update the eraser rmware................................................................................................................... 7

Change the order of the Erase mode menu.................................................................................... 8

Set the date and time on the eraser................................................................................................... 8

Managing log records ...........................................................................9

Print and save log records...................................................................................................................... 9

Delete all of the log records .................................................................................................................. 9

Reset the password .................................................................................................................................. 10

Print a receipt..........................................................................................11

Connect the eraser to your computer.................................................11

About the Erase mode menu................................................................12

Technical support...................................................................................13

Warranty information............................................................................13

Instruction manual

Product diagram

Front view

Error LED

Activity LED Power and link LED Drive bay

Eject button

OK button

ESC button

Menu navigation buttonsLCD display

Rear view

RS232 serial-based printer port

USB 3.0 port Power jack

Power button

Instruction manual

Introduction

You can use the SDOCK1EU3P standalone eraser dock to erase your 2.5 in. and 3.5

in. drives without having to connect to a computer, making it easier to reuse and

repurpose your SATA storage. For added security, you can connect a serial printer to

the SDOCK1EU3P and print a conrmation that includes the time and date of the erase,

as well as the erase mode that you used. The SDOCK1EU3P supports nine erase modes,

and can also be used as a single-bay dock for your SATA drive oering fast USB 3.0

performance, also known as USB 3.1 Gen 1 (5 Gbps).

The SDOCK1EU3P also works with 2.5 and 3.5 in. IDE hard drives, mSATA drives, and

M.2 drives when you use a compatible StarTech.com adapter. For more information

about the available adapters, see the links below:

Type of drive StarTech.com product

IDE hard drives StarTech.com adapter SAT2IDEADP

SATA to 2.5in or 3.5in IDE Hard Drive Adapter for HDD Docks

mSATA drives StarTech.com adapter SAT32MSAT257

mSATA SSD to 2.5in SATA Adapter Converter

M.2 drives StarTech.com adapter SAT32M225

M.2 NGFF SSD to 2.5in SATA Adapter Converter

Packaging contents

• 1 x hard drive eraser and USB 3.0 dock

• 1 x USB 3.0 cable

• 1 x universal power adapter

• 4 x power adapter plugs (NA/EU/UK/AU)

• 1 x quick start guide

Instruction manual

About the LED indicators

The SDOCK1EU3P includes three LED indicators that are located on the top of the unit.

See the tables below for more information about what the LED behaviors signify.

Red error LED

LED behavior Signies

Red LED is illuminated An error is occurring.

For more information about the error that is

occurring, consult the LCD display and use the

Menu navigation buttons to navigate.

Green activity LED

LED behavior Signies

Green LED is slowly blinking The erase request is being processed.

Green LED is rapidly blinking The drive is being erased.

Yellow power and link LED

LED behavior Signies

Yellow LED is briey

illuminated

The dock is turned on.

Yellow LED is illuminated The drive is being erased. When the process

is complete, the yellow LED will no longer be

illuminated.

Instruction Manual

Erasing a drive

The SDOCK1EU3P oers nine erase modes. For more information about the dierent

erase modes, consult the descriptions below.

Erase option Description of the process

Quick Erase The partition table is quickly erased.

Of the nine erase options, the Quick Erase is the

fastest option.

1-Pass Erase A full disk overwrite (all zeroes) is completed.

3-Pass (DoD 5220.22-M) A multi-pass overwrite based on DOD 5220.22-M

specications is performed.

This method erases the drive three times: the rst

time with zeroes (0x00), the second time with 0xFF,

and the third time with random characters.

3-Pass (CSEC ITSG-06) A multi-pass overwrite based on CSEC ITSG-06

specications is completed.

3-Pass (HMG Enhanced IS 5) A multi-pass overwrite based on HMG Enhanced IS5

specications is completed.

7-Pass (VSITR) A multi-pass overwrite based on VSITR Specications

is completed.

Custom Erase The user species the number of passes and the

pattern used.

Secure Erase The HDD/SSD ATA drive’s internal Secure Erase

command is executed.

Enhanced Secure Erase The HDD/SSD ATA drive’s internal Enhanced Secure

Erase command is executed.

Instruction Manual

Erase a drive

Before you erase a drive, make sure that you back up any important data from the

drive.

1. Plug one end of the universal power adapter into the power jack on the back of the

eraser and the other end into a power source.

2. Use the Power button on the back of the eraser to turn it on.

3. Place the drive that you want to erase in the drive bay. Push down on the drive to

make sure that it’s secured in the eraser slot.

4. To select an erase mode, use the Menu navigation buttons on the front of the

eraser to move up and down in the Erase mode menu.

5. Press the OK button.

Warning! After you press the OK button, don’t remove the drive from the eraser until

it has nished erasing. Removing the drive before the erase is complete may result in

damage to the drive.

6. When the drive is erased, the LCD display indicates that the process is complete. If a

serial printer is connected to the eraser, a receipt prints out.

7. To remove the drive, press the Eject button.

Erase a drive using customized settings

Before you erase a drive, make sure that you back up any important data from the

drive.

1. Plug one end of the universal power adapter into the power jack on the back of the

eraser and the other end into a power source.

2. Use the Power button on the back of the eraser to turn it on.

3. Place the drive that you want to erase in the drive bay. Push down on the drive to

make sure that it’s secured in the eraser slot.

4. Use the Menu navigation buttons on the front of the eraser to move up and down

in the Erase mode menu.

5. Select Custom Erase and press the OK button.

6. Select Run <x> Pass and press the OK button.

7. When the drive is erased, the LCD display indicates that the process is complete. If a

serial printer is connected to the eraser, a receipt prints out.

8. To remove the drive, press the Eject button.

Instruction Manual

Change the custom erase settings

You can customize the erase settings that are applied when you select Custom Erase in

the Eraser mode menu, including setting the number of passes and selecting a pattern

number.

1. Use the Menu navigation buttons on the front of the eraser to move up and down

in the Erase mode menu.

2. Select Custom Erase and press the OK button.

3. Do any of the following:

• To select a pass number, select Setup Pass # and press the OK button. Use the

Menu navigation buttons to select a number between 1 and 99 and press the

OK button.

• To select a pattern count, select Setup Pattern and press the OK button. Use the

Menu navigation buttons to select a number between 1 and 99 and press the

OK button. Use the Menu navigation buttons to select a Data Pattern number

and press the OK button. Use the Menu navigation buttons to select a number

between 1 and 99. Press the OK button.

To return to the Erase mode menu, press the ESC button until you have exited the

Custom Erase settings.

Instruction Manual

Using the Utility menu

The SDOCK1EU3P includes a Utility menu that you can use to view information about

the eraser, including system and disk information.

View the eraser details

1. Use the Menu navigation buttons on the front of the eraser to move up and down

in the Erase mode menu.

2. Select Utility and press the OK button.

3. Do any of the following:

• To view the disk info, select Show Disk Info and press the OK button.

• To view the product name and current version of rmware, select System Info

and press the OK button.

To return to the Erase mode menu, press the ESC button until you have exited the

Utility menu.

Update the eraser rmware

1. Connect a USB 3.0 cable to your computer and the USB 3.0 port on the back of the

eraser.

2. Use the Power button on the back of the eraser to turn it on.

3. Place a Firmware drive in the drive bay.

Note: You can use any type of drive, provided that it’s formatted to FAT32.

4. On your computer, copy the Firmware le to the drive in the eraser.

5. Use the Menu navigation buttons on the front of the eraser to move up and down

in the Erase mode menu.

6. Select Utility and press the OK button.

7. Select Update System and press the OK button.

8. When the LCD display says Complete, use the Power button to turn o the eraser.

9. Wait ve seconds and turn on the eraser again.

To return to the Erase mode menu, press the ESC button until you have exited the

Utility menu.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere StarTech.com Dockingstation Handbücher

StarTech.com

StarTech.com USBVGADOCK2 Bedienungsanleitung

StarTech.com

StarTech.com SATDOCKU3SP Bedienungsanleitung

StarTech.com

StarTech.com USB3SMDOCKV Bedienungsanleitung

StarTech.com

StarTech.com DK30C2DPPD Bedienungsanleitung

StarTech.com

StarTech.com 116N-USBC-DOCK Bedienungsanleitung

StarTech.com

StarTech.com TB2DOCK4KDHC Bedienungsanleitung

StarTech.com

StarTech.com USB5N1DOCK Bedienungsanleitung

StarTech.com

StarTech.com DK30BACDD Bedienungsanleitung

StarTech.com

StarTech.com USB3VDOCKD Bedienungsanleitung

StarTech.com

StarTech.com Thunderbolt 3 Series Bedienungsanleitung

StarTech.com

StarTech.com DK31C4DPPD Bedienungsanleitung

StarTech.com

StarTech.com USB3SDOCKHDV Bedienungsanleitung

StarTech.com

StarTech.com TB4CDOCK Bedienungsanleitung

StarTech.com

StarTech.com SATDOCKCRH Bedienungsanleitung

StarTech.com

StarTech.com SDOCK2U313 Bedienungsanleitung

StarTech.com

StarTech.com SATDOCKCRH Bedienungsanleitung

StarTech.com

StarTech.com 116E-USBC-DOCK Bedienungsanleitung

StarTech.com

StarTech.com SDOCK4U33 Bedienungsanleitung

StarTech.com

StarTech.com 8STUSB3DDOCKFT Bedienungsanleitung

StarTech.com

StarTech.com UNIDOCKU33 Bedienungsanleitung

StarTech.com

StarTech.com SATDOCK4U2E Bedienungsanleitung

StarTech.com

StarTech.com TBDOCKHDPBC Bedienungsanleitung

StarTech.com

StarTech.com Thunderbolt 3 TB3DKM2DPL Bedienungsanleitung

StarTech.com

StarTech.com DK30CHHPD Bedienungsanleitung

Beliebte Dockingstation Handbücher anderer Marken

Sony

Sony Dream Machine XDR-DS12iP Bedienungsanleitung

Acer

Acer USB Type-C Dock II Bedienungsanleitung

ATEN

ATEN UC-2000 Bedienungsanleitung

Xcellon

Xcellon HDD-202 Bedienungsanleitung

Dok

Dok CR09 Bedienungsanleitung

Philips

Philips BTM630/12 Bedienungsanleitung

IOGear

IOGear Travel Pro GUD3C09 Bedienungsanleitung

RKI

RKI SDM-E2 Bedienungsanleitung

iHome

iHome iP15 Bedienungsanleitung

VITURE ONE

VITURE ONE MOBILE DOCK Bedienungsanleitung

Lindy

Lindy 42984 Bedienungsanleitung

CipherLab

CipherLab 8001 Bedienungsanleitung

Pyle

Pyle PIPDSP2 Bedienungsanleitung

Avol

Avol AS2350 Bedienungsanleitung

Datalogic

Datalogic JoyaTouch Bedienungsanleitung

Philips

Philips DC190/79 Bedienungsanleitung

Targus

Targus DOCK315EUZ Bedienungsanleitung

Akasa

Akasa DuoDockX3 AK-DK08U3-BK Bedienungsanleitung