StarTech.com 110VDSLEXT2 Bedienungsanleitung

Manual Revision: 01/07/2015

For the most up-to-date information, please visit: www.startech.com

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

IT: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

110VDSLEXT2 / 110VDSLEX2GB / 110VDSLEX2EU

10/100Mbps VDSL2 Ethernet Extender Kit over

Single Pair Wire - 1.5km

*actual product may vary from photos

Instruction Manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment o and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved by StarTech.com could void the user’s

authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of

their respective holders.

Instruction Manual

Table of Contents

Introduction............................................................................................1

Packaging Contents ................................................................................................................................. 1

System Requirements.............................................................................................................................. 1

Product Overview ..................................................................................2

Front View .................................................................................................................................................... 2

Rear View...................................................................................................................................................... 2

Side View...................................................................................................................................................... 2

LED Indicators.........................................................................................3

Installation .............................................................................................4

Hardware Installation ............................................................................................................................. 4

DIP Switch and Mode Settings.............................................................5

Technical Support ..................................................................................6

Warranty Information............................................................................6

Instruction Manual

Introduction

Packaging Contents

• 1x Ethernet VDSL2 - Transmitter

• 1x Ethernet VDSL2 - Receiver

• 2x RJ45 Cables

• 8x Rubber Feet

• 2x Power Adapters

• 1x Instruction Manual

• 2x Wall mount screws and anchors

System Requirements

• 10/100 Mbps Ethernet Network

• Available AC electrical outlets

• RJ11 cable or RJ11 lines in building infrastructure

Instruction Manual

Product Overview

The Ethernet Extender Kit consists of x2 Ethernet VDSL2 Transmitter/Receiver units.

Either unit can be used at either end of your conguration (transmitting end or

receiving end), however the DIP switch settings should be modied according to your

specic needs based on direction of trac.

By default, all DIP Switch settings on each of the two units are set to the

downward (OFF) position.

See the DIP Switch and Mode Settings section for more information.

Front View

Rear View

Side View

DC Power Input

RJ11 VDSL Port RJ11 VDSL Port

Unit 1

DIP Switch

LED Indicators

DIP Switch

Unit 2

DC Power Input

RJ45 Port RJ45 Port

Instruction Manual

LED Indicators

LED

(Green) OFF ON (Solid) FLASHING

PWR

(Power) Power O Power On NA

ETH

(Ethernet) No RJ45 Link/Connection Connected Activity

DSL (VDSL) No VDSL Link/Connection Connected

Slow - Establishing

Connection

Fast – Sync / Activity

Instruction Manual

Installation

Hardware Installation

One of the Ethernet Extender Kits units should be considered a “Transmitting Unit”,

while the other should be considered a“Receiver Unit.”

Transmitter Unit

1. Place one of the units at the local location, this unit will act as the Transmitter Unit.

2. Connect the provided power adapter from an AC electrical outlet to the DC Power

Input on the Transmitter Unit. The “PWR” LED should light up solid.

3. Set all four of the DIP switches to the downward (OFF) position. This places the

Transmitter Unit in CO mode (Central Oce Mode).

4. Connect an RJ45 Ethernet cable to the RJ45 Port on the Transmitter Unit.

5. Connect the other end of the Ethernet cable into your Ethernet network device (eg:

Ethernet switch, modem, etc). The “ETH” LED should light up solid.

6. Connect an RJ11 phone cable into the RJ11 VDSL Port on the Transmitter Unit.

7. Connect the opposite end of the RJ11 cable to the RJ11 VDSL Port on the Receiver

Unit (or to your buildings RJ11 phone line infrastructure, depending on your setup).

Optional: Congure DIP switches 2 through 4 as necessary (see the “DIP Switch and

Mode Settings” section).

Receiver Unit

1. Place the second unit at the remote location, this unit will act as the Receiver Unit.

2. Connect the provided power adapter from an AC electrical outlet to the DC Power

Input on the Receiver Unit. The “PWR” LED should light up solid.

3. Set the DIP switch setting #1 to the upward (ON) position, with the remaining 3

DIP switches set to the downward (OFF) position. This places the Receiver Unit in

CPE mode (Customer Premises Equipment Mode).

4. If previously not completed, connect the RJ11 cable that was inserted into the RJ11

VDSL Port on the Transmitter Unit directly to the RJ11 VDSL Port on the Receiver

Unit (or from your buildings existing RJ11 analog telephone wiring, depending on

the setup from step 7 above.)

5. If the Transmitter and Receiver Units are able to successfully communicate with

each other, the “DSL”LED should ash slow, then fast while establishing a

connection, and eventually light up solid. The “DSL”LED will continue to ash when

there is activity between the Transmitter and Receiver Unit.

6. Connect your Ethernet network device (eg: Ethernet switch, modem, etc) to the

RJ45 Port on the Receiver Unit. The “ETH” LED should light up solid.

Optional: Congure DIP switches 2 through 4 as necessary (see the “DIP Switch and

Mode Settings” section).

Instruction Manual

DIP Switch and Mode Settings

The Ethernet Extender Kit units have a 4-position DIP switch for conguration of CO/

CPE, Prole, Band, and SNR.

By default, all DIP switch settings for both units are set to the downward “OFF”

position.

For initial setup, DIP switch 1 is usually set to the downward (OFF) position, ensuring

the unit is set to CO mode, set the 2nd unit to CPE mode by setting DIP switch 1 to the

upward (ON) position.

When using the Ethernet Extender Kit, one end (Transmitter or Receiver) must always

be set to “CO” (Central Oce), mode, while the opposite end must always be set to

“CPE”(Customer Premises Equipment) mode.

To ensure the Ethernet Extender Kit operates as intended with no problems,

errors, or disruptions, DIP switch settings 2 through 4 should be set to the same

position on both your Transmitter and Receiver Units.

CO or CPE Mode

Setting each unit to CO or CPE mode is usually based on which direction you want

the most bandwidth delivered. “Download” bandwidth, data sent from CO to CPE, is

generally higher than “Upload” bandwidth from CPE to CO.

If you need higher bandwidth from the Transmitter Unit to the Receiver Unit, set DIP

switch 1 to the downward (OFF) position at the transmitting end and the upward (ON)

position at the receiving end.

If you need higher bandwidth from the Receiver Unit to the Transmitter Unit, set DIP

switch 1 to the upward (ON) position at the receiving end, and the downward (OFF)

DIP1 DIP2 DIP3 DIP4

Function CO/CPE Mode Prole Mode Band Mode SNR Target

ON CPE 17a Symmetric 6dB

OFF CO 30a Asymmetric 9dB

Instruction Manual

position at the transmitting end.

Prole Mode

Prole Mode is the VDSL2 prole, 17a or 30a, with 30a allowing higher bandwidth

at longer distances. Set this DIP switch to the upward (ON) position for 17a, or the

downward (OFF) position for 30a, depending on your network requirements and

preferences.

Band Mode

Band Mode places the unit in either Symmetric or Asymmetric mode. Set this DIP

switch to the upward (ON) position for Symmetric mode, with both downstream and

upstream transmissions operating on the G.997 band plan, or set to the downward

(OFF) position for or Asymmetric mode, with asymmetric short range transmissions

operating at the highest available line rate.

SNR Target

SNR Target can be set for the unit to operate with ratios up to 6 or 9 dB. Set this DIP

switch to the upward (ON) position for a SNR ratio up to 6dB, or to the downward (OFF)

position for a SNR ratio up to 9dB.

Instruction Manual

Technical Support

StarTech.com’s lifetime technical support is an integral part of our commitment to

provide industry-leading solutions. If you ever need help with your product, visit

www.startech.com/support and access our comprehensive selection of online tools,

documentation, and downloads.

For the latest drivers/software, please visit www.startech.com/downloads

Warranty Information

This product is backed by a two year warranty.

In addition, StarTech.com warrants its products against defects in materials

and workmanship for the periods noted, following the initial date of purchase.

During this period, the products may be returned for repair, or replacement with

equivalent products at our discretion. The warranty covers parts and labor costs only.

StarTech.com does not warrant its products from defects or damages arising from

misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their

ocers, directors, employees or agents) for any damages (whether direct or indirect,

special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,

or any pecuniary loss, arising out of or related to the use of the product exceed the

actual price paid for the product. Some states do not allow the exclusion or limitation

of incidental or consequential damages. If such laws apply, the limitations or exclusions

contained in this statement may not apply to you.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere StarTech.com Extender Handbücher

StarTech.com

StarTech.com ST12MHDLNHR Bedienungsanleitung

StarTech.com

StarTech.com SV565LANDUA Bedienungsanleitung

StarTech.com

StarTech.com USB110EXT2 Bedienungsanleitung

StarTech.com

StarTech.com USB110EXT2 Bedienungsanleitung

StarTech.com

StarTech.com SV565UTP Bedienungsanleitung

StarTech.com

StarTech.com USB2G4LEXT2NA Bedienungsanleitung

StarTech.com

StarTech.com ST121UTP Bedienungsanleitung

StarTech.com

StarTech.com USBthere USB204EXTFIB Bedienungsanleitung

StarTech.com

StarTech.com SV565UTP Bedienungsanleitung

StarTech.com

StarTech.com IREXT Bedienungsanleitung

StarTech.com

StarTech.com USBthere USB100EXT Bedienungsanleitung

StarTech.com

StarTech.com ST121HDT4P Bedienungsanleitung

StarTech.com

StarTech.com SV565UTPU Bedienungsanleitung

StarTech.com

StarTech.com ST12MHDLANU Bedienungsanleitung

StarTech.com

StarTech.com ST121HDBT20L Bedienungsanleitung

StarTech.com

StarTech.com STDHVHDBT Bedienungsanleitung

StarTech.com

StarTech.com STUTPRXWAL Bedienungsanleitung

StarTech.com

StarTech.com 8STST121HDBT20S Bedienungsanleitung

StarTech.com

StarTech.com ST121HDBTE Bedienungsanleitung

StarTech.com

StarTech.com SV565UTPHDU Bedienungsanleitung

StarTech.com

StarTech.com EOC110K Systemhandbuch

StarTech.com

StarTech.com SV565UTPUSA Bedienungsanleitung

StarTech.com

StarTech.com USBthere USB110EXT Bedienungsanleitung

StarTech.com

StarTech.com POEEXT1GAT Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung