StarTech.com HSB4SATSASBA Bedienungsanleitung
Manual Revision: 09/23/2014
For the most up-to-date information, please visit: www.startech.com
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
HSB4SATSASBA
4 Drive Trayless 3.5” SATA/SAS Mobile Rack
*actual product may vary from photos
Instruction Manual
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Changes or modications not expressly approved by StarTech.com could void the user’s
authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Instruction Manual
i
Table of Contents
Introduction............................................................................................1
Packaging Contents ................................................................................................................................. 1
System Requirements.............................................................................................................................. 1
Product Diagram ....................................................................................2
Front View .................................................................................................................................................... 2
Rear View...................................................................................................................................................... 2
Installation ..............................................................................................3
Hardware Installation .............................................................................................................................. 3
3.5in Hard Drive Installation.................................................................................................................. 4
3.5in Hard Drive Removal....................................................................................................................... 5
How to Use ..............................................................................................6
Connecting the Hard Drive.................................................................................................................... 6
LED Indicator .............................................................................................................................................. 7
Disconnecting the Hard Drive.............................................................................................................. 7
Initializing the Hard Drive ...................................................................................................................... 7
Technical Support ..................................................................................9
Warranty Information............................................................................9
Instruction Manual
1
Introduction
Packaging Contents
• 1x 4 Drive Trayless 3.5in SATA/SAS Mobile Rack
• 8x Installation screws
• 2x Drive bay keys
• 4x SATA cables
• 1x Instruction Manual
System Requirements
• 1x Computer System with SATA connectivity and three available 5.25” bays
• 2x Available SATA Power Connections
• Up to four 3.5” SATA/SAS Hard Drive(s)
Instruction Manual
2
Product Diagram
Front View
Rear View
1. 4x 3.5” Drive bays
2. 4x 3.5” Drive bay key hole
3. 4x 3.5in LED indicators
1. 2x SATA Drive Power Connector ports
2. 4x SATA Data Connector ports
3. Hard Drive LED Enable/Disable
4. Fan speed control switch (High/Low)
1
3
4
23
1
2
Instruction Manual
3
Installation
WARNING! Hard drives and storage docks require careful handling, especially when
being transported. If you are not careful with your hard disk, lost data may result.
Always handle your hard drive and storage device with caution. Be sure that you
are properly grounded by wearing an anti-static strap when handling computer
components or discharge yourself of any static electricity build-up by touching a large
grounded metal surface (such as the computer case) for several seconds.
Hardware Installation
1. Ensure your computer system is powered down, and the power cable has been
disconnected from the Power Supply.
2. Open your computer case (refer to the computer user manual for details), and place
the 3.5in SATA/SAS HDD Backplane into four available 5.25” slots, lining up the side
installation holes on the HSB4SATSASBA (pictured below), with installation holes on
the 5.25” slot inside the computer.
Instruction Manual
4
3. Hold the HSB4SATSASBA into place by lining up the screw holes on HSB4SATSASBA
with the corresponding mounting holes in your 5.25in bays. Next, x the
HSB4SATSASBA to your 5.25in bays by screwing 4 of the included screws into any of
the installation holes on both side of the 5.25” bay (8 screws in total).
4. Connect the 4x SATA cables (4x included) from an available SATA host port on your
motherboard to the SATA data connector ports on the back of the HSB4SATSASBA.
5. Connect 2x SATA Power connectors from your power supply to the SATA power
connector ports on the back of the HSB4SATSASBA.
Note: For optimal performance, ensure each SATA power connector is on a dierent
power rail. Failure to do so may result in power disruption while swapping drives.
3.5in Hard Drive Installation
1. Insert either of the included bay keys into the your desired 3.5in Drive bay key holes
depending on which drawer you intend to install the drive into. And Turn the key
clockwise into the unlock position.
2. Pull the drive door handle to open the drive bay
Instruction Manual
5
3. Insert your desired drive
4. Close the drive door.
3.5in Hard Drive Removal
1. Insert either of the included bay keys into the 3.5in Drive bay key holes depending
on which type of drive you intend to install. And Turn the key clockwise into the
unlock position.
2. Pull the drive door handle to open the drive bay
Instruction Manual
6
3. Remove your drive
4. Close the drive door.
Note: It is important to eject or unmount the hard drive from your computer system
before physically removing the drive. See How to Use - Disconnecting the Hard
Drive section for instructions.
How to Use
Connecting the Hard Drive
Once the drive has been installed in the drive bay, the drivers will install automatically,
and the inserted drive will be accessible as though it were installed within the system.
Note: some operating systems may require that the system be scanned for hardware
changes from within device manager, for the newly connected drive(s) to be
recognized.
Prior to using the drive, it will need to be formatted according to your operating
system requirements.
Refer to Initializing the Hard Drive.
Instruction Manual
7
LED Indicator
The HSB2535SATBK oers 3.5in LED indicators, to enable you to monitor drive activity.
The LED will ash while the hard drive is being accessed. Do not remove the enclosure
from the host computer while the LED is ashing, as it could damage the drive or the
enclosure, resulting in data loss.
Disconnecting the Hard Drive
Windows
The drive should be uninstalled from device manager, or unmounted using third party
hot swap software.
Note: Removing the connected drive while it is active in the system could result in
losing or corrupting data stored on the drive.
Mac OS X
To safely disconnect the attached drive from the host computer, close any windows
listing the contents of the removable drive. Once all windows are closed, click on the
icon for the drive on the desktop, and drag it to the Trash Can icon on the desktop.
Allow 5 seconds before physically removing the enclosure/drive from the computer.
Initializing the Hard Drive
1. If the SATA Hard Drive is blank it may need to be initialized and formatted before
use. From the main Windows desktop, right-click on “My Computer” (“Computer” in
Vista/ 7 / 8), then select Manage. In the new Computer Management window, select
Disk Management from the left window panel.
Inhaltsverzeichnis
Andere StarTech.com Rack & Stand Handbücher
StarTech.com
StarTech.com ARMPIVOTHD Bedienungsanleitung
StarTech.com
StarTech.com PROJWALLMNT Bedienungsanleitung
StarTech.com
StarTech.com WALLSTS1 Bedienungsanleitung
StarTech.com
StarTech.com SHELF-1U-12-FIXED-S Bedienungsanleitung
StarTech.com
StarTech.com FPWTLTB1 Bedienungsanleitung
StarTech.com
StarTech.com ARMSLIMDUOS Bedienungsanleitung
StarTech.com
StarTech.com DRW110SAT Bedienungsanleitung
StarTech.com
StarTech.com RKPNLTL2UV Bedienungsanleitung
StarTech.com
StarTech.com WALLMOUNTH4 Bedienungsanleitung
StarTech.com
StarTech.com ARMSLIMDUAL2USB3 Bedienungsanleitung
StarTech.com
StarTech.com HSB100SATBK Bedienungsanleitung
StarTech.com
StarTech.com LAPTOP-SIT-STAND Bedienungsanleitung
StarTech.com
StarTech.com KBTRAYADJ2 Bedienungsanleitung
StarTech.com
StarTech.com RKPNLHV2U Bedienungsanleitung
StarTech.com
StarTech.com ARMPIVOT2USB3 Bedienungsanleitung
StarTech.com
StarTech.com RK4242BK24 Bedienungsanleitung
StarTech.com
StarTech.com ARMDUALPS Bedienungsanleitung
StarTech.com
StarTech.com RACK-2U-14-BRACKET Bedienungsanleitung
StarTech.com
StarTech.com 42U Bedienungsanleitung
StarTech.com
StarTech.com VIDWALLMNT Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
